Surpass AUDIO SOURCE Series User manual

DIGITAL TUNER
With Usb/Bt/Aux In

※ Be sure to read the instructions in this section carefully before use.
※ Make sure to observe the instructions in this manual as the conventions of safety symbols
and messages regarded as very important precautions are included.
※ We also recommend you keep this instruction manual handy for future reference.
When Installing the Unit
※ Do not expose the unit to rain or an environment where it may be splashed by water or other
liquids,as doing so may result in fire or electric shock.
※ Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is
specified may result in fire or electric shock.
※ Do not cut, kink, otherwise damage nor modify the power supply cord. In addition, avoid using the
power cord in close proximity to heaters, and never place heavy objects -- including the unit itself -- on
the power cord, as doing so may result in fire or electric shock.
※ Be sure to replace the unit's terminal cover after connection completion. Because high voltage is
applied to the speaker terminals, never touch these terminals to avoid electric shock.
※ Be sure to ground to the safety ground (earth) terminal to avoid electric shock. Never ground to a
gas pipe as a catastrophic disaster may result.
※ Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted
surface. Doing so may result in the unit falling down, causing personal injury and/or property damage.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Page 1
SAFETY PRECAUTIONS
WARNING
AUDIO SOURCE SERIES
DIGITAL TUNER

Page 2
When the Unit is in Use
※ Should the following irregularity be found during use,immediately switch off the power,disconnect
the power supply plug from the AC outlet and contact your nearest dealer.Make no further attempt to
operate the unit in this condition as this may cause fire or electric shock.
·If you detect smoke or a strange smell coming from the unit.
·If water or any metallic object gets into the unit.
·If the unit falls, or the unit case breaks.
·If the power supply cord is damaged (exposure of the core, disconnection, etc.)
·If it is malfunctioning (no tone sounds.)
※ To prevent a fire or electric shock, never open nor remove the unit case as there are high voltage
components inside the unit. Refer all servicing to your nearest dealer.
※ Do not place cups, bowls, or other containers of liquid or metallic objects on top of the unit. If they
accidentally spill into the unit, this may cause a fire or electric shock.
※ Do not insert nor drop metallic objects or flammable materials in the ventilation slots of the
unit's cover, as this may result in fire or electric shock.
When Installing the Unit
※ Never plug in nor remove the power supply plug with wet hands, as doing so may cause electric
shock.
※ When unplugging the power supply cord, be sure to grasp the power supply plug; never pull on the
cord itself. Operating the unit with a damaged power supply cord may cause a fire or electric shock.
※ When moving the unit, be sure to remove its power supply cord from the wall outlet.
Moving the unit with the power cord connected to the outlet may cause damage to the power cord,
resulting in fire or electric shock. When removing the power cord, be sure to hold its plug to pull.
※ Do not block the ventilation slots in the unit's cover.
Doing so may cause heat to build up inside the unit and result in fire.
※ Avoid installing the unit in humid or dusty locations,in locations exposed to the direct sunlight,
near the heaters,or in locations generating sooty smoke or steam as doing otherwise may result
in fire or electric shock.
CAUTION
AUDIO SOURCE SERIES DIGITAL TUNER

When the Unit is in Use
※ Do not place heavy objects on the unit as this may cause it to fall or break which may result in
personal injury and/or property damage.In addition,the object itself may fall off and cause injury and/or
damage.
※ Make sure that the volume control is set to minimum position before power is switched on.
Loud noise produced at high volume when power is switched on can impair hearing.
※ Do not operate the unit for an extended period of time with the sound distorting.
This is an indication of a malfunction, which in turn can cause heat to generate and result in a fire.
※ Contact your dealer as to the cleaning. If dust is allowed to accumulate in the unit
over a long period of time, a fire or damage to the unit may result.
※ If dust accumulates on the power supply plug or in the wall AC outlet, a fire may result.
Clean it periodically. In addition, insert the plug in the wall outlet securely.
※ Switch off the power, and unplug the power supply plug from the AC outlet for safety purposes when
cleaning or leaving the unit unused for 10 days or more.
Doing otherwise may cause a fire or electric shock.
We warrant that the hardware products it manufactures will be free from defects in materials and
workmanship.
The warranty term,beginning on the date of invoice,is one year for Parts replacement,two years for parts
repair and six months on accessories.
This warranty does not cover damage or failure caused by alterations, mishandling, abuse, misuse,
neglect, accident or resulting from any cause other than a product defect.
In case of defects in material and workmanship under normal use and conditions,we will replace or repair
products covered under this limited warranty that are returned to our facility.
To request warranty service, you must contact our international sales team within the warranty period,
ship the products back to us in their original or equivalent packaging (freight prepaid). If we repair or
replace a product, its warranty term is not extended.
Information contained in this manual is subject to change without prior notice and does not represent a
commitment on the part of the vendor. We shall not be liable for any loss or damages whatsoever arising
from the use of information or any error contained in this manual.
It is recommended that all services and repairs on this product be carried out by us or its authorized
dealer.
This product must only be used for the purpose it was intended by the manufacturer and in conjunction
with this operating manual.
We cannot accept any liability whatsoever for any loss or damages caused by service,maintenance or
repair by unauthorized personnel,or by use other than that intended by the manufacturer.
Page 3
LIMITED WARRANTY
DISCLAIMER
AUDIO SOURCE SERIES
DIGITAL TUNER

Page 4
Installing Rack Ears
Thank you for purchasing the Digital Tuner.
To ensure long and trouble-free use of the equipment,please read all instructional
materials provided with the unit.
Package Contents
A pair of rack ears are included that allow the user to mount the player in a standard 19"
audio/electronics rack. To install the rack ears, refer to the diagram and follow these steps:
1. Remove three screws from the side panel of the player toward the front.
2. Place one rack ear in proper position,
paying attention to correct alignment.
3. Reattach the three screws.
4. Repeat procedure for second rack ear,
located on the other side of the unit.
AC Power Cord
.....................................................................................
1
User Manual
.................................................................................. 1
AM Antenna
Audio Cable (RCA)
......................................................................................
......................................................................
1
1
Tuner
..............................................................................................
1
Remote Control
.................................................................................
1
Rack Ear
DAB+/FM(RDS) Antenna
.........................................................................................
2
............................................................................
1
..............................................................................
1
Bluetooth Antenna
AUDIO SOURCE SERIES DIGITAL TUNER

Page 5
1. STANDBY:
Push this button to activate and deactivate this unit.
2. USB port:
Allows to play USB disk.
3. AUX IN jack:
This 3.5mm jack is an audio line input jack. Can connect a portable digital player or other external
audio device here.
4. Screen:
This shows various types of information for the media.
5. VOL+ / VOL-:
To turn up or down the output volume of the media.
6. NEXT / PREV:
When in the USB and Bluetooth mode: Press these buttons to skip to next or previous track.
When in the FM(RDS) and DAB+ mode:
Press these buttons to skip the frequency by +0.05 or -0.05 MHZ.
Press and hold these buttons to scan through the frequencies in a semi-automatic way.
7. PRESET CHOICE (1,2,3,4,5):
Keep pressing for several minutes to store the favorite stations. And press them to choose to play the
stored stations (1 to 5). Through Remote Control that total 9 favorite stations can be stored.
8. MODE:
Press this button to choose audio source among USB,DAB+,FM,AM,Bluetooth and Aux in.
9. ENTER:
Press this button to confirm a selection.
10. MENU (works with buttons of ‘PREV’, ‘NEXT’ and ‘ENTER’):
When in the FM mode(including RDS):
〈Scan setting〉: To select scan way of All stations or Strong stations.
〈System setting〉:
Language selection: English,Portugués,Español,Française,Italiano,Deutsch.
SW version: Shows the software version.
Factory reset: Clears the memory completely and scans again for the available stations.
〈Audio setting〉: Allows to select Stereo or Mono mode.
When in the DAB+ mode:
〈Full scan〉: Allows to scan through all stations.
〈System setting〉:
Language selection: English,Portugués,Español,Française,Italiano,Deutsch.
SW version: Shows the software version.
Factory reset: Clears the memory completely and scans again for the available stations.
〈Prune〉: Deletes (or not) stations that are either no longer transmitting or have moved frequency.
(2) (3)
(1)
(4) (5) (6) (7) (8)
(9) (10) (11) (12) (13) (14)
AUDIO SOURCE SERIES
Front Panel
DIGITAL TUNER

Page 6
〈DRC〉: Dynamic Range Compression provides a feature that reduces the volume of louder sounds
and boosts the volume of quieter sounds. It can be a handy feature when listening to audio at
lower volumes.
〈Manual tune〉: Allows to scan through the frequencies manually.
11. PRESET:
Press this button to review the 60 stored stations,press ‘NEXT’ or ‘PREV’ to choose a desired station
then press ‘ENTER’ to play this station.
12. MUTE:
To press this button to mute the audio of this unit,press it again to activate audio.
13. INFO:
Allows to show the related information for the FM(RDS) and DAB+ mode.
14. AUTO SCAN:
Press this to scan through and store the stations automatically. The stored stations can be review in
the PRESET list. Press it again to stop scanning.
(1) (2) (3) (4) (5) (6) (7) (8)
(9) (10)
1. Antenna DAB+/FM connector:
Connect the included DAB+/FM antenna here.
2. Antenna AM connector:
Connect the included AM antenna here.
3. RCA Out jacks:
These (unbalanced) outputs send audio signal to the external mixer,amplifier,etc.
4.XLR Out jacks:
These (balanced) outputs send audio signal to the external mixer,amplifier,etc.
5. BT ANT:
Connect the included bluetooth antenna here.
6. Indication of XLR jack:
1:GND, 2:Hot, 3:Cold.
7.Power switch:
This turns the unit on and off.
8. AC IN connector:
Connect the included power cord here.
9. IR JACK:
Connect additional IR receiver and attach to other surface where it provides the best reception from
the remote control.
10. RS232 interface:
Serial control through the RS232 connector can be used to operate this unit from a computer or other
external device.
AUDIO SOURCE SERIES
Names & Functions of Front Panel
Rear Panel
DIGITAL TUNER

Page 7
The shipment does not contain the batteries.
Please get and insert the suitable batteries - AAA/1.5V before use.
(1) (2)
(3)
(4)
(7)
(8)
(10)
(11)
(14)
(6)
(9)
(18)
(12)
(13)
(16)
(17)
(19) (20)
(21)
(22)
(23)
(22)
(21)
(24) (25)
(26)
(27) (28)
(30)
(29)
(5)
(15)
AUDIO SOURCE SERIES
Remote Panel
DIGITAL TUNER

Page 8
1. STANDBY:
Press this button to activate and deactivate this unit.
2. MUTE:
Press this button to mute this unit’s audio.
Buttons of 3 - 7: These buttons are used for other models.
8.DAB+ :
Press this to switch the input source to “DAB+ Mode”.
9. FM(containing RDS)：
Press this to switch to the input of source to “FM Mode”.
10. AM:
Press this to switch to the input of source to “AM Mode”.
11. BT:
Press this to switch the input source to “Blueetooth Mode”.
12. USB:
Press this to switch the input source to “USB Mode”.
13. AUX:
Press this to switch the input source to “AUX IN” by connecting additional audio player.
14. MENU:
Please refer to the operations of front panel “MENU”.
15. INFO:
Allows to show the related information for the FM(RDS) and DAB+ mode.
16: SCAN:
Press this to scan through and store the stations automatically.
17. PRESET:
Press this button to review the 60 stored stations,press ‘NEXT’ or ‘PREV’ to choose a desired station
then press ‘ENTER’ to play this station.
18. CD/TUNER:
Press this button to switch between controlling left and right side media when use additional function
buttons (19 - 29) for another model of 2CH Media Player.
19. PLAY/PAUSE:
Press this to start,resume,or pause the playback.
20. STOP:
Press this to stop playback.
21. SKIP (PREV. & NEXT) button:
When in the USB and Bluetooth mode: Press these buttons to skip to previous or next track.
22. Fast-reverse & Fast-forward button:
Press and hold these buttons to scan at fast reverse or fast forward playback for other models.
23. OK button:
Press this to confirm a selection.
24. REPEAT:
Press this turn the repeat playback function on/off.
25. PROGRAM: This button is used for other models.
26. EQ selection:
Press this to select the EQ mode among Classic,Rock,Pop,Jazz and Flat.
27. VOL +/- button:
Press this to adjust the output audio level.
28. FOLDER:
Press this to select the folder when use USB media.
29. Number buttons:
Use these number buttons to select tracks or preset stations.
30. DISPLAY:
Push this button to make the screen light on/off.
AUDIO SOURCE SERIES
Names & Functions of Remote Control
DIGITAL TUNER

Page 9
Carefully read the operation manuals of the devices to be connected and them connect them correctly.
Before making connections,turn this unit and all equipment to be connected off (standby).
USB Flash Disk
Portable audio player
AM Antenna
DAB+/FM(RDS)
Antenna Bluetooth
Antenna
Computer
Mixer,Amplifier,recorder, etc.
AC power cord
AC100-240V
• System Tuner
• Compatible media USB,Bluetooth,FM(RDS),DAB+(DAB),AM,Aux in
• Playable formats USB: MP3,WAV
• Bluetooth 5.0 versionversion
• Frequency range FM(RDS): 87.50 - 108.00 MHz
DAB+(DAB): 87.50 - 108.00 MHz
AM: 522 - 1620 Khz
• Frequency response 20 Hz - 20 Khz (±0.5 dB)
S/N ratio More than 105 dB•
• . . . %T H D Less than 0 005
• Unbalanced out L/R RCA terminal
Load impedance: Over 10 kΩ/kohms
Output level: 2 Vrms (Max. 10 dBu) at 10 kΩ/kohms load
• Balanced out L/R XLR terminal (1:GND, 2:Hot, 3:Cold)
Load impedance: Over 600Ω/ohms
Output level: 8.23 dBu (Max. 24 dBu) at 600Ω/ohms load
• Power supply AC 100-240V 50/60 Hz
• Power consumption 30W (0.5W standby)
• Product size 330x267x49mm
372x267x49mm (with rack ears)
• Carton size 520x355x117mm
• .Net weight 2 80kg
Gross weight kg• 3.50
AUDIO SOURCE SERIES
Connection Illustration
Specifications
R-BLUETOOTH
DIGITAL TUNER

NOTE:
Page 10
AUDIO SOURCE SERIES DIGITAL TUNER

The products are constantly improving,subject to change without prior notice.
CAUTION: Do not open the equipment cover arbitrarily,
so as not to electric shock. Please contact the professionals
to maintian if necessary.