Surtek MD8422 User manual

Parts
G2:M4x12(x8)
30mm
G1:M4x30 (x8) H1:(x8) H2:(x8)
12mm
F:Φ4x12(x8)
d
d
a
gi
e:VESA plate (x2)
a:pole (x1) c:Grommet/
clamp support (x1)
d:Main mount (x2)
i:S3/S4/S5 wrench (x1)
m:M10 (x1) o:Grommet Base Plate (x1)
k:M10 Washer (x1) l:Spring (x1)j:Abutment
Plate (x1)
g:wire clip (x1)
b:Clamp (x1)
Step 1 Install the Clamp and Pole on a Desk Step 2 Install the pole and the main mount
Option A: Clamp installation
Option B: Grommet installation
1. Place wire clip (g) on pole (a).
2. Place swivel arm (d) on pole (a). Tighten screw with wrench (i) at
proper position.
Make sure there is a plane desk hole whose diameter is over 100mm.
1. Connect grommet support (o)with 3 pieces of
M5x18 (f) and tighten it with wrench(i) (figure 3).
1. Connect clamp support (c) and pole (a)
with 3 pieces of M5x18 (f) and tighten it with
wrench(i) (figure 1) 2.
Connect clamp (b) and clamp support (c)
with pre-positioned screws M8X12 and
tighten it with wrench(i)(figure 2) connect
the pole on the desk,adjust the distance
according to the thickness of desk.
2. Connect pole(a) and Abutment
Plate(j), M10 Washer(k),Spring
Washer(l),screw M10(m) with Big
wrench(n).Tighten the screw M10(M)
n:Big wrench(x1)
a
o
g
figure 1
figure 3
figure 2
a
c
f
i
b
plastic knob
j
figure 4
f:M5x18 (x3)
MD8422
Hold monitors: 17”-27“
Weight capacity: 2.2-13.2 lbs (1-6kg)
Compatible VESA patterns: 75x75mm/100x100mm
INSTALLATION MANUAL
WARNING!
Incorrect installation may cause loss of life, personal injury and
damage of property. Please read the following information before
installation.
If you do not understand the manual or meet any problem, please
contact your local qualified installation person.
If any of the parts are damaged or lost, do not install it. If you need to
exchange parts, please contact retailer.
This item holds 17” - 27” LCD monitors less than 13.2lbs weight.
This item is simple and easy to install on a desk or disassemble.
To ensure security, the capacity of the desk need to be over 3 times of
the weight of all loading (include mount, monitor and its accessories).
Do not use this item for any purpose or in any configuration not
explicitly specified in this instruction.
For safety, be careful with the slideable parts of the item.
Be careful with the wires when installation of the monitor.
We are not responsible for: reformed or incorrect installation, beyond
the capacity, damage during usage.
l
m
n
k

4.1 4.2
4.3
5.1 5.2
please make sure the weight of the
monitor in under the load capacity.
Step 5 Adjustment of torque force
Step 4 Cable management
unscrew the
pre-positioned screw
tighten the
screw
pinch and pull out
pinch and push in
tie the wires
open and pull out
Step 3 Install monitor,VESA plate and main mount.
H1or H2
F
G1 or G2
unscrew the pre-positioned screw
Drive screw
WARNING:
Make sure the screws
are tightened.
WARNING:
Make sure the screws
are tightened.
3.1
3.3
3.4 3.5
3.2
+: Increase torque force
- : Decrease torque force
1. The monitor could stop at any height after hung on the
mount. No adjustment needed.
2. The monitor bounces itself after hung on the mount. Press
down the monitor with one hand and make sure the arm is
horizontal. Use S5 wrench and turn the screw in “-” direction
with the other hand (little by little) until the monitor can stop at
any height.
3. The monitor falls itself after hung on the mount. Raise the
monitor with one hand and make sure the arm is horizontal. Use
S5 wrench and turn the screw in “+” direction with the other
hand (little by little) until the monitor can stop at any height.
Adjustment of torque force
after installation
Adjust torque force
WARNING
WARNING
Decrease Increase
1. Make sure the monitor is hung on the mount before adjustment.
2. Make sure the weight of monitor is within the capacity.