SV3C P6S User manual

-1-
P6S Wi-Fi PanTilt AI Camera
Quick Setup Guide
Please read this user's guide carefully before using the product and keep it properly
※The screen displays and illustrations in this user's guide are examples only, please
refer to the actual product

-2-
Product Description
Product Precautions
The proper environment temperature for this camera range from -10℃ to
50℃.Please avoid exposing it to too much hotter or colder environment.
Please do not use this camera in somewhere moist or highly risk of getting
water inside of it, thus to ensure this camera of precise electronics a long service
life.
For better using experience, please keep the front and both sides of the
camera lens away from objects reflective as glass, white wall etc. So that the picture
function well without overexposure.
Make sure the camera has been placed in areas of good reception of Wi-Fi
signal or at lease within the signal zone. Set it up away from somewhere might
jamming signal as metal or microwave oven.
Product Use
Turn on the Camera
Plug the power into the power of the camera and wait a few seconds for the
camera to automatically turn on.
Voice prompt at power-on ”The system is starting up, please wait”. If there is
no voice reminder, please restore the factory settings and try again.
Note: Do not twist the head of the camera to force it to rotate after turning it
on. If you need to adjust the monitoring orientation, you can adjust it through the
PT function of the mobile APP.

-3-
Restore the Factory Settings
Insert the reset pin* into the reset hole and press for 5 seconds to restore the
factory settings. (When connecting or reconfiguring the camera for the first time,
make sure that the camera is in the factory reset state).
Download APP
Download and install “P6slite” from IOS app store or Android app store or scan
the QR code below to get APP information.
(Android / ISO scan code adaptive)
Download more product information at：http://www.ipcam.xin
Users can register and log in via email (please use real email to retrieve
password later).

-4-
Note: Please be sure to use your account to log in the APP, otherwise some
camera functions may not work properly.
Add Camera
Open the P6SLite APP, click “+” in the upper right corner of the home page,
select “Add Wi-Fi Device”, click “Next” to add WiFi camera.

-5-
Method 1：add camera by scan QR Code
1. Select “Please use the scan code distribution network to connect the router”.
2. Choose your wireless network and enter the password, click "Next".
3. Please face the QR code on the camera lens and keep it at distance of about
15 cm, then if you hear”WiFi connection, please wait” click "Next".

-6-
4. Wait for the camera to connect to WIFI,
If the camera is successfully connected to WIFI, you will hear "WiFi is
connecting, please wait ....network connection successful" and see the camera in
the device list.
Method 2：add camera by AP Hotspot
1. Select “Please use the AP hotspot distribution network”.
2. Click the button to jump to the WiFi setting page (Android system not have
this page, please skip this step).
3. Select the camera's AP hotspot, it's an AP hotspot beginning with
"ZWAP_NG...", enter password: 01234567 to connect AP hotspot (If you do not find
the AP hotspot, please try to reset the camera).

-7-
4. Return to APP, select your wireless network in the available wireless list to
connect. (WiFi signal strength must be greater than 3 cells).
5. Enter your WiFi password, click "Confirm".
6. Wait for the camera to connect to WiFi.

-8-
View in Real Time
Open the P6SLite APP, click the connected camera on the home page, and you
can browse in real time. Through the camera's control interface, you can adjust the
camera's sharpness, horizontal and vertical angles, as well as screen capture and
recording, and remote calls operation, etc.
View in Real Time Video Playback
Video Playback
The camera can only use the historical video playback function after installing a
MicroSD memory card. After the MicroSD memory card is installed and turned on,
the camera will automatically start recording video.
In the camera control interface, click the button ‘Playback’ to enter the
historical video playback interface. You can drag the timeline to select the time
period to be played back, or you can use the button ‘Date’ to select historical
videos on different dates.

-9-
Alarm and AI Human Tracking
Click “Arm/Disarm” to open or closed the alarm push (image send to mailbox
+ mobile phone), at the same time you must set the correct alarm parameters, such
as open email and push notification in "Humanoid Tracking".
Turn on the humanoid tracking. when human beings appear on the screen, the
camera can detect human figures, you can open the Humanoid Tracking, or select
the required trigger actions, such as SD Card Snapshot, SD Card Record, Push
Notification, Alarm Sound, etc., you can set up ‘Armed all day’ or ‘Custom arming’,
you can set Sensitivity, Detection area, etc.
Video Share
Open the P6SLite APP, click the ‘···’ button on the top right corner of the PT AI
camera device preview on the homepage, and select ‘Sharing management’ to
enter the sharing settings and invite others to watch. The person being shared
needs to download the P6SLite APP, register an account and log in to view.

- 10 -
Camera Setting
Open the P6SLite APP, enter the ‘Settings’ function page of the camera on the
homepage, here you can configure all camera settings.