SweTrack MaxiTracker User manual

Instruction Manual
MaxiTracker
Issued by SweTrack Electronics AB
Version 2.1 2021-10-22

www.swetrack.com 2
Introduction
Thank you for choosing a MaxiTracker from SweTrack.
This manual describes how to get started with the product and allows you to get
acquainted with the product’s exterior. Read the manual carefully before you start using
the product. You can nd more information, as well as contact information, in our support
center www.swetrack.com/support.

www.swetrack.com 3
LED indicators and buttons
The mobile signal indicator ashes quickly when the device is searching for a signal, and
ashes more slowly when the device is connected to the mobile network. The power
indicator ashes quickly when the battery is running low, and ashes more slowly when
the battery is charged and has normal voltage. When charging, the indicator lights up
steadily until charging is complete. The GPS indicator ashes when positioning is in
progress, and is off when no positioning is in progress.

www.swetrack.com 4
Charging and start-up
Before using the product, charge the battery for at least 3 hours. Connect the magnetic
end of the USB cable to the charging socket of the product as illustrated below, and the
other end of the cable to a wall charger with USB socket. The power indicator will be
solid when the product is charging. When the product is fully charged, the indicator will
start ashing instead. When the product is charged, disconnect the charger and start
the product by holding down the power button for about 3 seconds until the LEDs start
ashing. To turn off the product, hold down the power button until the LEDs go out. You
can now place the track transmitter on the intended tracking object and proceed to the
next page of this manual.

www.swetrack.com 5
Create an account in the mobile app
The MaxiTracker is controlled through the SweTrack Live app. In the SweTrack Live app,
you can see the device’s current location, enable geofences, request location history, and
more.
Visit the App Store (iOS) or Google Play (Android) and search for SweTrack Live. The app is free.
Once you’ve started the app, select Sign up found at the bottom of the login screen. Then ll in your
name, your email address and choose a password. Finally, you need to enter the device’s IMEI number.
The easiest way to do this is to click the Scanner button and hold the phone’s camera against the IMEI
barcode on the back of the product. You can also select Text and enter the IMEI number manually.
Once you have lled in all elds, click the button Create Account. You then log in with your email
address and the password you chose.
SweTrack Live can also be used from the browser on a PC or Mac. To visit SweTrack Live from your
computer, go to www.swetrack.com/live in your browser. You use the same login information on the
computer version as in the mobile app.
1
2
3
Download the app
Create an account
Use SweTrack Live from a computer

www.swetrack.com 6
Activating a data plan
Once you have charged and powered on your MaxiTracker, you will need to sign up for
a data plan in order to use the product. The data plan includes unlimited tracking across
Europe. Without mobile data, the product can not communicate with the Internet and
transfer its position data to you.
1. Go to the web app www.swetrack.com/live and log in to your account. If you do not have an account,
click on “Sign up”, follow the instructions and then log in.
2. Go to the “Data Plans” page and click on “My Cards”.
3. Click on “Add card” and then ll in your card details. Then click on the blue “Save” button.
4. Then click on the “Devices without data plan” tab.
5. Select the device or devices for which you want to create a data plan and then click on “Create a
data plan”.
1. Go to the web app www.swetrack.com/live and log in to your account.
2. Go to the “Data Plans” page and click on “Devices with data plan”
3. Select the devices you want to cancel a data plan, and then click “Cancel data plan”
The data plan / data plans will now be cancelled and not renewed until you choose to reactivate them
by going to the tab “Devices without data plan” and clicking “Activate data plan”.
1
2
How do I start a data plan?
Cancel a data plan
Never perform unauthorized modications to the device, such as replacing the built-in SIM-card with another
SIM-card. The device only works with the factory installed SIM-card. Also, do not install the built-in SIM-card
into other equipment, the SIM-card will be permanently blocked and rendered unusable, even if it is reinstalled in
the SweTrack device. Unauthorized modications can damage the product and will cause the one-year factory
warranty to be permanently invalidated.

www.swetrack.com 7
Using the Mobile App
Once you have created an account and activated a subscription, the product will start to work within
about 20 minutes. You will then be able to see it on the map in the SweTrack Live app or via a
computer by going to www.swetrack.com/live.
The product’s position is automatically updated every 2 minutes when the product is in motion.
Keep in mind that the product is, by default, only active when the built-in vibration sensor notes
movements. lf you do not see the product on the map in the app, you may therefore need to shake
it a little so that it starts up.
In the app, in addition to displaying the current position, you can also change te device settings and
activate different types of alarms.

www.swetrack.com 8
Power saving mode
By default, the product is registered to only search and report position data to the app when it is in motion.
However, other functions, such as mobile antennas, are turned on. This setting is called Normal power saving
mode. With this mode, you can change settings at any time as the product is always connected to the
network, but it only searches for new positions as it moves. You can also activate an aggressive power saving
mode, which means that all functions are switched off when the product is stationary.
This saves a lot of power, but it also means that any settings you change do not take effect until the product
wakes up. It is also possible to deactivate all energy saving functions. This means that the product also
reports position data when it is stationary. This suits you who need continuous updating about the product’s
position even when the object is stationary, but this consumes more battery.
Start by rst navigating to My Devices that you reach by tapping the icon on the far left in the lower
navigation menu.
Here you get a list of all the devices that you have added to your account. Select device by tapping the
arrow icon to the right of the device name. This will open the device settings.
By pressing Power Saving Mode, you open a pop-up with different options for Power Saving modes.
The switch that is activated will be marked blue.
Select an option by tapping the corresponding switch and then save by clicking on Save.
1Changing the power saving mode

www.swetrack.com 9
Warranty & Service Information
This page contains information about our warranty and service terms.
You’ll nd answers to the most common questions about our products and services in our Support
Center, located at www.swetrack.com/support.
lf you can not nd the answer to your question in this manual or in the support center, contact our
customer service at support@swetrack.com.
We at SweTrack take the integrity of our customers seriously, and we never share personal data or
information about how the product is used with any third party. You can nd our full privacy policy by
going to the page privacy policy.
SweTrack provides a one year hardware warranty on all products to all customers. The warranty
covers original hardware defects and does not cover software failures or errors resulting from externaI
damage and / or improper handling of the product.
1
2
3
Support & Service
Privacy Policy
Hardware Warranty
Contact information
If you can not nd the answer to your question in this manual or in the support center, contact our customer
Table of contents
Other SweTrack GPS manuals