SwimLife SwimFit Dual Stream User manual

EFFECTIVE DATE: January 1, 2018 (supersedes all others)
CAUTION: THIS GUIDE IS FOR REFERENCE ONLY! All installations must follow local electrical
and building codes. Please consult your local business and planning division for your codes in your area.
SWIMLIFE SWIMSPAS WILL NOT BE RESPONSIBLE FOR ANY ERRORS IN INSTALLATIONS OR CODE INFRACTIONS.
2018 MODEL
SWIMSTREAM
SERIESSwimFit / SwimExpert
INSTALLATION
GUIDE

1. Types of installs
1.1 Free Standing with Cabinet above ground
1.2 Free Standing in Deck with or without cabinet
1.3 Below Grade Indoor
1.4 Below Grade Outdoor
2. Model, Specifications and Electrical
2.1 Model and Series
Shell Dimensions and Weights
2.2 Electrical Specifications
2.3 Wiring Size
2.4 North American GFCI Installation
2.5 European GFCI Installations
3. Delivery and Handling Considerations
3.1 Retailer Delivery
3.2 Direct Deliveries
3.3 Crane Deliveries
3.4 Fork Lift Deliveries
3.5 Roller Deliveries
3.6 Warnings
4. Above Grade
4.1 Preparation
4.2 Concrete
4.3 Rooftop / Balcony Install
Cross Section Side View of
2018 14ft. SwimFit /SwimExpert Swimspa
Install Inground
Cross Section Topside View of
2018 14ft. SwimFit /SwimExpert Swimspa
Install Inground
5. Below Grade or Partial In Grade Installations
5.1 Backfilling Exclusion
5.2 Excavation
5.3 Vault/Bunker Specs
5.4 Base of Support
5.5 Crawl Space
5.6 Ground Water
Cross Section Top View of
2018 14ft. SwimFit /SwimExpert Swimspa
Inground...
Cross Section End View of 2018 14ft. SwimFit/
SwimExpert Swimspa Full & Partial
Inground Installation
Cross Section Side View of
2018 14ft. SwimFit /SwimExpert
Swimspa Install Inground
5.7 Service Access
5.8 Water Test
5.9 Overall Support
5.10 Insulation
5.11 Set Up and Assembly
5.12 Equipment Protection
6. Serviceability, Accessibility
and Protection
6.1 Equipment Protection
6.2 Serviceability
6.3 Rodent Protection
7. Filling and Draining
7.1 General Considerations
7.2 Indoor Installations
7.3 Outdoor Installations
8. Auxiliary Heating Options
8.1 Gas Heaters
8.2 Other Methods
8.3 Auxiliary By Pass
9. Ventilation, Humidity Control,
Other Indoor Considerations
9.1 Humidity Control
9.2 Ventilation
9.3 Hardcover
9.4 Floor Drainage
10. Hardcover Storage
10.1 Hardcover
10.2 Cover Lifters
10.3 Pool Shed
11. By Laws and Disclaimer
11.1 Building Code
11.2 Excavation
11.3 Recommendations
11.4 Professionals
11.5 Sunlight
14ft. SwimFit / Expert
SWIMSTREAM
Installation Manual
Page 1
Page 1
Page 1
Page 1
Page 1
Page 2
Page 2
Page 3
Page 3
Page 4
Page 5
Page 6
Page 6
Page 6
Page 6
Page 6
Page 6
Page 6
Page 7
Page 7
Page 7
Page 7
Page 8
Page 9
Page 10
Page 10
Page 10
Page 10
Page 10
Page 10
Page 10
Page 11
Page 12
Page 13-14
Page 15
Page 15
Page 15
Page 15
Page 15
Page 16
Page 17
Page 17
Page 17
Page 17
Page 18
Page 18
Page 18
Page 18
Page 18
Page 18
Page 18
Page 18
Page 19
Page 19
Page 19
Page 19
Page 19
Page 20
Page 20
Page 20
Page 20
Page 20
Page 20
Page 20
Page 20
Page 20
Page 20

1. Types of installations:
1.1 Free Standing with cabinet above ground
This installation refers to a Swimspa that is placed
on a concrete pad, above ground and with a SwimLife
Cabinet. Can be adjacent to a deck or butted up to a deck.
1.2 Free Standing in Deck
This installation refers to a Swimspa that is placed
on a concrete pad, above ground and with or without
a SwimLife cabinet and with or without a frame.
This Swimspa is surrounded on 1 or 2 sides by deck.
1.3 Below Grade Outdoor
This installation refers to a Swimspa that is
placed on a concrete pad, below grade and
without a SwimLife Cabinet. Can be partially
or fully recessed in the ground.
1.4 Below Grade Indoor
Indoor installations of a Swimspa must be
placed on a concrete pad. Swimspas can be
partially or fully recessed in the oor.
1
1.1 Free Standing with
cabinet above ground
1.2 Free Standing in Deck
1.3 Below Grade Outdoor
1.4 Below Grade Indoor

2. Model Series, Specification and Electrical
2.1
14ft.
SwimFit
SWIMSTREAM
SWIMSPA
2.1
14ft.
SwimExpert
SWIMSTREAM
SWIMSPA
2
2,532 lbs /
1,149 Kg
18,445 lbs /
8,369 Kg
1,900 US gallons /
7,220 Litres
L
52.75” / 133.99 cm
174” x 93” /
441.96 cm x 236.22 cm
2,532 lbs /
1,149 Kg
18,445 lbs /
8,369 Kg
1,900 US gallons /
7,220 Litres
L
52.75” / 133.99 cm
174” x 93” /
441.96 cm x 236.22 cm

3
2.2 Electrical Specifications
SAFETY COMES FIRST. WHEN INSTALLING & USING ELECTRICAL
EQUIPMENT, BASIC SAFETY PRECAUTIONS MUST ALWAYS BE FOLLOWED!
1. READ AND FOLLOW ALL INSTRUCTIONS
2. Electrical installation must be completed by a qualied electrician in accordance with all National, Regional
and Local Codes and Regulations in effect at the time of installation.
3. Connect only to a dedicated circuit protected by a class ‘A’ two-pole ground fault circuit interrupter (GFCI)
4. Use copper conductors only!
5. The Swimspa equipment and all electrical plugs, outlets and lights within 1.5m (5ft) of the unit must be
G.F.C.I protected. Consult your electrician or local electrical authority for further details.
6. A green colored terminal or a terminal marked “G”, “GR”, “Ground”, or “Grounding” is located inside the
supply terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected
to the grounding by means provided in the electric supply service panel with a continuous copper wire
equivalent in size to the circuit conductors supplying the equipment.
7. At least two lugs marked “BONDING LUGS” are provided on the external surface or on the inside of the
supply terminal box or compartment. To reduce the risk of electric shock, connect the local common
bonding grid in the area of the Swimspa to these terminals with an insulated or bare copper conductor not
smaller than No.6 AWG (Canada/Europe) / No.8 AWG (USA).
8. All eld installed metal components such as rails, ladders, drains or other similar hardware within 3 m (10 ft)
of the hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than
No.6 AWG.
2.3 Wiring Size
NORTH AMERICA / EUROPE WIRE SIZE
Please consult your applicable electrical codes related
to the size of the breakers and the wire. Take into
consideration the length of the cable and increase
as required.

2.4 North American GFCI Installation
Installation of the GFCI - Circuit Breaker, including ampere sizing and selection of conductor
size and type, must be performed by a qualied electrician in accordance with the National
Electrical Code, or the Canadian Electrical Code, and all Federal, State / Provincial and local
codes and regulations in effect at the time of installation.
SwimLife highly recommends the use of a new GFCI breaker for
all of its products. Older GFCI’s may have tripping issues.
NORTH AMERICA
SwimFit 240 V / 60 HZ / 50A
SwimExpert 240 V / 60 HZ / 60A
4
240 VOLT
SINGLE GFCI WIRING
240 VOLT
TWO PACK WIRING

230 VOLT DUAL
PHASE RCD WIRING
5
2.5 European R.C.D. Installation
Important Note:
Installation of the R.C.D. - Circuit Breaker, including ampere sizing, GFCI Security Breaker and
selection of conductor size and type, must be performed by a qualied electrician in
accordance with National, Regional and Local Codes and Regulations in effect
at the time
of installation.
EUROPE (single phase)
SwimFit 230 V / 50 HZ / 40A
SwimExpert 230 V / 50 HZ / 40A
230 VOLT
SINGLE PHASE RCD WIRING

6
3.3 Crane Deliveries
3.4 Fork Lift Deliveries
3.5 Roller Deliveries
3.1 Retailer Delivery
3 Delivery and Handling
Considerations
3.1 Retailer Delivery
All SwimLife Swimspas are shipped with a layer of protective
foam wrap, plastic lm and cardboard for added protection.
Each Swimspa is shipped from the factory strapped onto a
wood skid. If your Swimspa is to be delivered by your local
SwimLife retailer, it will generally arrive on a at bed truck
or low prole trailer. Typically, the dealer will arrive with the
necessary equipment to maneuver the Swimspa from the
truck. The Swimspa can then be lifted by a crane into place.
3.2 Direct Deliveries
Like the retailer delivery, your Swimspa will come wrapped
and skidded the exact same way, however, your Swimspa
may arrive on a 48 ft. or 53 ft. common carrier closed box trailer.
You can arrange the exchange at a local cross docking facility
to a atbed truck. The Swimspa can then be lifted by a crane
into place.
3.3 Crane Deliveries
Most installations require the use of a crane. When a crane is
used for lifting, place the straps under the Swimspa, ensuring
that the plumbing lines and ttings are not stressed and / or
damaged and a spreader is used. The straps should be secured so
that they will not slip in any direction and strap spreaders utilized
to prevent undue structural side load on the Swimspa shell.
3.4 Fork Lift Deliveries
If you are removing the Swimspa using a forklift, please make
sure to use 8 – 10’ / 2.5-3 m extended forks and pick up swim
spa at the equipment end.
3.5 Roller Deliveries
Although it is recommended to install your Swimspa by crane,
it may be pushed along rollers by 10 to 12 able-bodied adults
(see image).
If rollers are to be utilized, we recommend that at least
six 4”/ 10 cm diameter pipes, 8’ / 2.5 m long, be placed under
the shell to move it across a soft lawn, down a path, etc.
3.6 Warnings!
• Do not move or place the Swimspa on its side
• Never lift or handle the Swimspa by its plumbing
• the Swimspas dry weight is in excess of 2302 lbs. / 1044 kgs.
• Please ensure lifting equipment is sufcent for the job.
Manually lifting of the Swimspa should be done with the
proper manpower.
• We strongly recommend the installation to be done by a
SwimLife Retailer.

4 Base Of Support – Load Specications
4.1 Preparation
Installation of a level concrete pad is mandatory.
Dig out and level the ground 20 - 30 cm (8 -12 in.) below your desired base level. Install 20 -25 cm (8-10 in.) of crushed
stone. If there is a possibility that the pad could shift by freezing / thawing ground movement (such as in clay regions,
and / or areas with high water tables) concrete footings extending below the frost line are recommended.
4.2 Concrete
Install 10-15 cm (4 - 6 in.) of poured concrete. The concrete support slab must be at and level in-order to properly level
the Swimspa during installation. The concrete pad should be slightly larger than the dimensions for the Swimspa, but
it may be expanded even further for esthetic purposes or to allow more space for walking around the Swimspa. En-
sure that your concrete pad is capable of supporting 1500 kg/m2(250 lbs. / ft2). If the Swimspa is purchased with
steps your concrete pad should be made large enough to accommodate the size of the step.
4.3 Second Level / Balcony Installation
You must know the load tolerance and compare it to the weight of the Swimspa lled with water and people. When
in doubt, a load distribution assessment carried out by an engineer should be consulted, who can guarantee the best
location choice. Ensure that your second level balcony is capable of supporting 1500 kg/m2(250 lbs. / ft2). While
swimming, the motors and water ow in all Swimspas generate vibrations that are directly transferred to the base on
which the Swimspa is installed. These can therefore be felt in lower levels. In this case, the support area must
be properly engineered. Install a oor drain in the event there are any problems with the plumbing to sure that this
water has a place to drain.
7

174”/ 441.96 cm*
Length of 14ft. SwimFit AquaStream Swimspa
*
SwimLife Swimspas., can not be held liable for the accuracy of this drawing, it is purely provided as a guide only. As each
Swim Spa installation has it own set of challenges and variations due to materials used and location of the install.
Exploded Side View of 2018 14ft SwimFit AQUASTREAM
Swimspa Install Above Ground
Sono Tube** with re-bar and poured concrete in cavity space
Sono Tube** with
re-bar and
poured concrete
in cavity space
Minimum 4”* thick concrete slab
with reinforced wire mesh
Minimum 8-10”* of crushed stone (.75 to1” stone size)
Ground level
Ground level
**
Sono Tubes only required in installtions that are in regions that experience freezing and thawing.
46 1/4in
±
3/4in (117.48cm
±
1.91cm)
Height of Swim Spa Acrylic Lip
48.75in ±1/2in (123.83 cm
±1.27 cm
)*
Height of Swim Spa
Exploded Side View of 2018 14ft SwimFit SWIMSTREAM
Swimspa Install Above Ground
**
Sono Tubes only required in installtions that are in regions that experience freezing and thawing.
174”/ 441.96 cm
*
Length of 14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
52 3/4 in
±1/2 in
(133.99 cm
±1.27 cm)
Height of Swimspa
50in
±
3/4 in (127.00 cm
±
1.91cm)
Height of Swimspa Acrylic Lip
Cross Section Side View of 2018 14ft. SwimFit / SwimExpert
SWIMSTREAM Install Above Ground
8
* SwimLife Swimspas., can not be held liable for the accuracy of this drawing, it is purely provided as a guide only. As each Swim Spa installation has it own set of challenges and variations due to materials used and location of the install.

174”/ 441.96 cm*
Length of 14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
93”(236.22cm)*
Width of 14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
9* SwimLife Swimspas., can not be held liable for the accuracy of this drawing, it is purely provided as a guide only.
As each Swim Spa installation has it own set of challenges and variations due to materials used and location of the install.
Cross Section Topside View of the 2018
14ft. SwimFit / SwimExpert Swimspa Install Above Ground

10
Cross Section Topside View of the 2018
14ft. SwimFit / SwimExpert Swimspa Install Above Ground
5 Below Grade or Partial In Grade Installations
Cabinet with Solid State Frame
5.1 Backfilling Exclusion
SwimLife Swispas will void any warranty of swim spas that are back-lled.
5.2 Excavation
Call before you dig! Please make sure you have any permits in place that are required from your municipality.
5.3 Vault/Bunker Specifications
When recessing the swim spa all or part way below ground level, a concrete base along with a concrete retaining wall
to hold back the earth is required. This forms a Vault or ’bunker‘, in which the swim spa is placed.
5.4 Base of Support
It is necessary that a concrete base be poured level and reinforced in order to support the swim spa. In addition,
if you are in an area that experiences freezing and thawing concrete footings should be added as outlined in sec-
tion 4 of this guide.
5.5 Crawl Space
It is recommended leaving a 24 in. (61 cm) wide crawl-space around the entire unit to ensure adequate
accessibility on the all sides for service access. At the Equipment end it is recommended to have a 3 ft. / 90 cm
crawl space for work space.
5.6 Ground Water
The Vault will be the lowest part of your backyard and therefore good drainage is essential. A properly designed drain
system and sump pump complete with a oat switch should be constructed as part of the crib and should be located
at the equipment end of the Swim Spa. This should prevent ood damage from ground water that may enter the crib.

93”(236.22cm)
*
Width of 14ft. SwimFit / SwimExpert
SWIMSTREAM Swimspa
174”/ 441.96 cm
*
Length of 14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
11
Cross Section Top View of 2018 14ft.SwimFit / SwimExpert
SWIMSTREAM Swimspa Inground...

93”(236.22cm)*
Width of 14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
93”(236.22cm)*
Width of 14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
52 3/4 in ±1/2 in
(133.99 cm ±1.27 cm)
Height of Swimspa
50in ±3/4 in (127.00 cm ±1.91cm)
Height of Swimspa Acrylic Lip
52 3/4 in ±1/2 in
(133.99 cm ±1.27 cm)
Height of Swimspa
50in ±3/4 in (127.00 cm ±1.91cm)
Height of Swimspa Acrylic Lip
12
Cross Section End View of 2018 14ft. SwimFit / SwimExpert
SWIMSTREAM Swimspa Full Inground Installation...
Cross Section End View of 2018 14ft. SwimFit / SwimExpert
SWIMSTREAM Swimspa Partial Inground Installation...
* SwimLife Swimspas., can not be held liable for the accuracy of this drawing, it is purely provided as a guide only.
As each Swim Spa installation has it own set of challenges and variations due to materials used and location of the install.

13
174”/ 441.96 cm*
Length of14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
52 3/4 in ±1/2 in
(133.99 cm ±1.27 cm)
Height of Swimspa
50in ±3/4 in (127.00 cm ±1.91cm)
Height of Swimspa Acrylic Lip
Cross Section Side View of 2018 14ft. SwimFit / Swim Expert
SWIM STREAM Swimspa Install Inground...
Notes:

14
174”/ 441.96 cm*
Length of14ft. SwimFit / SwimExpert SWIMSTREAM Swimspa
52 3/4 in ±1/2 in
(133.99 cm ±1.27 cm)
Height of Swimspa
50in ±3/4 in (127.00 cm ±1.91cm)
Height of Swimspa Acrylic Lip
Notes:
* SwimLife Swimspas., can not be held liable for the accuracy of this drawing, it is purely provided as a guide only.
As each Swim Spa installation has it own set of challenges and variations due to materials used and location of the install.

5 Below Grade or Partial In Grade Installations
Cabinet with Solid State Frame (Cont’d...)
5.7 Service Access
Future service must be considered at the time of design and installation. You must be able to access all sides and
areas of your Swimspa. Difcult access will result in supplemental service labour charges not covered by the factory
warranty. Consider easily removable deck materials.
5.8 Water Test
During shipping and handling some of the components may have shifted. Please ensure the Swimspa is tested for 48
hours before you prepare the installation of the surrounding/nish deck around your Swimspa. Even though all units
are tested in our plant, some transport/site handling damage may occur and we suggest you make sure the Swimspa
is perfectly waterproof before nalizing your installation.
5.9 Overall Support
Your SwimLife Swimspa is equipped with a factory installed load support substructure, which distributes the weight of
the water over the entire foot print area of the Swimspa. The supporting oor must be even and level. Although the lip
of the Swimspa must be supported to ensure it remains level, NEVER SUSPEND a Swimspa from a deck or oor by
the outer acrylic edge, as this will lead to product damage and/or serious personal injury.
5.10 Insulation
It is important to create a well-insulated vault when installing a Swimspa in ground. This can be done a couple of ways:
1) Use insulated concrete forms when pouring the walls of the vault. This will accomplish two things, one it will
provide the wall support needed to build a deck and two it will give the insulation required to keep the running
costs to a minimum
2) After installing the concrete block for the walls of the vault, add Styrofoam Blue insulation
or Thermal Shield blanket to the interior walls to create well insulated area
3) Finally purchasing a Polartec Insulated Mat or a thermal shield blanket, which can be placed on the concrete pad
before the Swimspa is placed. This will allow you to create a fully insulated vault area. Installing styrofoam
insulation for the Swimspa to sit on will void warranty!
5.11 Set Up and Assembly
Set-up of your Swimspa will vary depending on whether you have purchased an SwimFit or SwimExpert model.
Once your Swimspa is set into place, you are ready to install the steel support legs and connect the equipment package.
5.12 Equipment Protection
The equipment must be located in an area where it will remain dry and will not be exposed to rain, snow or ground
water. When your Swimspa is to be installed above ground, the factory cabinet is designed for both protection,
insulation and accessibility. When your Swimspa is to be installed fully or partially in the ground, or if you have ordered
a Swimspa without a cabinet: it is necessary that the equipment be installed in an area that is dry, protected from the
elements, has proper ventilation, and is easily accessible for service.
15

16

6.3 Serviceability
6 Serviceability, Accessibility
and Protection
6.1 Equipment Protection
The equipment must be located in an area where it will remain dry
and will not be exposed to rain, snow or ground water. When your
Swimspa is to be installed above ground, the factory cabinet is
designed for both protection, insulation and accessibility.
When your Swimspa is to be installed fully or partially in the ground,
or if you have ordered a Swimspa without a cabinet, it is necessary
that the equipment be installed in an area that is dry, protected from
the elements, has proper ventilation, and is easily accessible
for service.
6.2 Serviceability
Ensure that access to the equipment, and the working area around
the equipment, is large enough to accommodate a service person.
6.3 Rodent Protection
For any installation, protection from rodent infestation is imperative. If
the Swimspa is being installed with a cabinet, as long as your concrete
pad is level there should be no need for any further protection against
rodents. However, if the Swimspa is being installed in ground without
a cabinet it is important to take the precautions required to make sure
rodents don’t make a home in your vault area. Protect access points
and repair if needed.
1717