SWIT S-2040 User manual

Congratulations on your purchase of this product. Please read this user manual carefully.
Features
 New generation chip-array LED technology, outputs bright but soft & glareless light;
 S-2040 23W power consumption, equivalent to a 80W halogen bulb;
 S-2050 48W power consumption, equivalent to a 150W halogen bulb;
 10%-100% dimmerable
 5000K output, 5600K/3200K filter;
 Lightweight; cool-touch design.
Product view
Fig 1 Fig 2
Caution
1. Never attempt to open the device. Refer all servicing to
qualified personnel.
2. Never insert anything into the cooling vent to avoid damage
or short circuit.
3. Keep the light away from rain or moisture.
4. Please do not stare at the turned on LED light.
5. Keep the filters clean.
6. When powering through DC-IN socket by S-7104 D-tap
cable, please make sure the power supply's voltage and
power meet the light input requirements.
7. Working temperature -10 ~40 ℃ ℃
8. Keep the cooling vent clear to avoid damage.
Clean
Use a soft, dry cloth to clean the LED light. If you clean the
light with soft cloth slightly moistened with neutral detergent,
please dry the surface of the light with a soft, dry cloth. Do
not use a damp cloth or alcohol, gasoline and other solvents
of any kind.
Specifications
Model S-2040 S-20 0
Input DC 6V-17V DC11V-17V
Power Approx. 23W Approx. 48W
Beam angle Approx. 50° Approx. 50°
Illuminance 900 lx @ 1 meter
2200 lx @ 1 meter
Color temp. 5000K itself, with 5600K&3200K filter
Mass Approx. 500g
Dimension 103×157×84mm
Working temp. -10 ℃ ~+40 ℃
Storage temp. -20 ℃ ~+55 ℃
Package
LED light
×
1
Cold shoe slot
×
1
Power adaptor S
-
7104
×
1
User manual
×
1
LED Camera Light S-2040/S-20 0
USER MANUAL
SWIT Electronics Co., Ltd.
Tel [phone]
Fax [phone]
http //www.swit.cc
E-mail [email protected]
1. 5600K filter
2. Barn door
3. 3200K filter
4. Barn door
5. Cooling vent
6. Switch on/off
7. Knob
8. Cold shoe mount
9. Dimmer
10. DV mount slot (only S-2040)
11. DC-IN socket
12. Protection cover

Usage
1. Power supplies
S-2040
S-2040 is 6-17V voltage input and offers various power supply methods.
● By S-8040 battery
① Make sure there’s no power lead connected into DC-IN socket and the light is
switched off (turn the switch to “ 〇 ”).
② Press and slip off the protection cover. See Fig 3
③ Align a fully charged S-8040 battery to the DV mount slot to same side, and
press tightly in. Slide the battery downward to snap together. See Fig 4
● By DV battery
① Press and slip off the protection cover. See Fig 3
② Align the mount S-7004 to the DV mount slot to same side, and press tightly
in. Then slide the S-7004 mount downward to snap together. See Fig 5- ①
③ Fix the DV mount with two screws.
④ Make sure the light is switched off (turn the switch to “ 〇 ”). Mount a fully
charged battery to the S-7004 mount. Fig 5- ②
Remark After use, please fix on the protection cover.
There’re the following types of S-7004 for choice (Optional Purchase)
Model Compatible battery type Recommended SWIT battery
S
-
7004F
SONY NP
-
F770/970
S
-
8972, S
-
8970, S
-
8770
S
-
7004P
Panasonic
CGA
-
D54S/D28S
S
-
8D62, S
-
8D54, S
-
8D28
S
-
7004J
JVC BN
-
V4
28U
S
-
8428
S
-
7004C
Canon BP
-
930/945
S
-
8945, S
-
8845
S
-
7004U
SONY
BP
-
U60/30
S
-
8U62
S
-
7004E
Canon DSLR LP
-
E6
S
-
8PE6
S
-
7004B
Panasonic VW
-
VBG6
S
-
8BG6
S
-
7004V
JVC BN
-
VF823
S
-
8823
● By DC adaptor S-7104
① Make sure the light is switched off (turn the switch to “ 〇 ”). Plug the pole end
of S-7104 into the DC-IN socket.
② Plug the D-tap end of S-7104 to the camera auxiliary power tap or the
battery’s D-tap output socket. See Fig 6.
S-20 0
S-2050 is 11-17V voltage input and only accepts D-tap power supply.
By DC adaptor S-7104
① Make sure the light is switched off (turn the switch to “ 〇 ”). Plug the pole end
of S-7104 into the DC-IN socket.
② Plug the D-tap end of S-7104 to the camera auxiliary power tap or the
battery’s D-tap output socket. See Fig 6.
2. Fix the LED light to the camera
● By cold shoe
Anticlockwise screw the knob to draw the bolt back, slide the cold shoe mount into
camera, and then clockwise adjust the knob to fasten. See Fig 7.
● By screw mount
Fix the cold shoe slot to the screw mount by the screw. Fix the light to the cold
show as the above Instructions. See Fig 8.
3. Adjust the angle of the light
Hold the light, and adjust the light upward or downward. See Fig 9.
4. Open barn doors and filters
Open the barn doors and filters to about 45°.
. Switch on:
Turn the switch to “ I ”.
6. Adjust the illuminance
Adjust the illuminance from 10% to 100% by the dimmer.
7. Adjust color temperature
Output 5600K light by using 5600K filter; Output 3200K light by using 3200K filter
Fig 4
Release button
Screw hole
Battery
release
Fig 6
Pole plug
Fig 7
Fig 9
Adjust upward
or downward
Fig 5
Fig 8
Press and slip
to release
Fig 3
ONLY S-2040
ONLY S-2040
ONLY S-2040