Sybaritic Dermalife RelaxWell Ocean Pod User manual

RELAXWELL OCEAN POD
OWNER’S MANUAL
206824 ROP.10.0719.1.U

Dermalife®RelaxWell Ocean Pod System
Owner’s, Installation, and Service
Manual
Voice Direct Dial: [phone]
Toll Free: [phone]
Fax: [phone]
Web Site: http://www.sybaritic.com
E-mail: [e-mail]
Before using the RelaxWell Ocean Pod System, please
read this Owner’s Manual thoroughly to ensure proper
and safe use.
SYBARITIC, INC.
9220 James Avenue South
Minneapolis, MN 55431
USA

TABLE OF CONTENTS
Page
Section 1 Introduction
1.1 Purpose of the Manual 1
1.2 Customer Service 1
1.3 Disclaimer 1
1.4 Copyright 2
Section 2 Safety
2.1 Preinstallation Technical Safety Tips 3
2.2 General and User Safety 3
2.3 Safety Precautions 4
2.4 Important Safety Instructions 5
Section 3 Shipping, Storing, and Installation Conditions
3.1 Shipping, Storing, and Installation Conditions 8
Section 4 Electrical and Plumbing Requirements
4.1 Electrical Installation Requirements 9
4.2 Plumbing Installation Requirements 10
4.3 Connecting to Oxygen System (Optional) 11
Section 5 Installation Drawings
5.1 Removing Panels 14
5.2 Removing the Hood Cover 14
5.3 Removing the Hood 15
5.4 Adjusting the Legs 16
5.5 Electrical, Water, DVD, and Audio Connection Drawings 16
Section 6 Product Introduction
6.1 RelaxWell Ocean Pod System Introduction 19
6.2 RelaxWell Ocean Pod System Features 19
6.3 RelaxWell Ocean Pod System Contraindications 20
6.4 Water Intake 20
Section 7 Operation
7.1 The Control Panel(s) 21
7.2 RelaxWell Ocean Pod Component Drawings 23
7.3 Preparation for Operation 24
7.4 How to Run Your First Warm-Up Session 24
7.5 Working with the Options 25
7.6 Working with the RelaxWell Ocean Pod System 27
7.7 How to Run Your First Bath Session 33
7.8 Working with the RelaxWell Ocean Pod Bath System 33

TABLE OF CONTENTS
(Continued)
7.9 Safety Shut Off 35
7.10 Stopping Your Session 35
7.11 Turning Off Your RelaxWell Ocean Pod System 35
7.12 Program Descriptions and Device Working Charts 35
Section 8 Service (Hood)
8.1 Removing the Hood Cover 48
8.2 Removing the Hood and Changing the Strut Nut 48
8.3 Principle Water Diagram with Valve Connections 49
8.4 Water Connection Types 50
8.5 Water Jet 50
8.6 Mist Jet 51
8.7 Radiant Heat Emitter 51
8.8 Speaker 52
8.9 Temperature Sensor 52
8.10 Opening the LCD Housing 52
8.11 Replacing Parts in the LCD Housing 54
Section 9 Service (Bottom)
9.1 Removing Panels 56
9.2 Drainage 56
9.3 Aroma System 57
9.4 Mineral/Vitamin System 57
9.5 Vibratory Bed 58
9.6 On-off Switch 59
9.7 Hood Switch 60
9.8 Supply Transformers 60
9.9 Steam Generator 61
9.10 Replacing the Heating Element 62
9.11 Replacing the Thermal Fuse 62
9.12 Replacing the MG Anode 63
9.13 Replacing the Water Level Sensor 63
Section 10 Advanced Electronics and Troubleshooting
10.1 Electrical Connections 65
10.2 Other Components on the PC Board 66
10.3 Principal Water and Electrical Diagram 67
10.4 Principal Water and Electrical Component List 68
10.5 Troubleshooting 69

TABLE OF CONTENTS
(Continued)
Section 11 Maintenance and Reinstallation
11.1 General Cleaning and Mandatory Use of Pre-Approved Solution 71
11.2 Cleaning the Shell 72
11.3 Cleaning the Underbed Area 73
11.4 Cleaning Contact Surfaces (Bed, Head Pillow, Interior of Shell) 73
11.5 Cleaning the Steam Generator 73
11.6 Cleaning the Aroma Diffusion System 74
11.7 Cleaning the System Drain 74
Section 12 Specification Information
12.1 General 75
12.2 Supplied Accessories 76
APPENDICES
Owner Record A
Owner’s Registration Form B
Standard Warranty C

Section 1 Introduction
RelaxWell Ocean Pod 1
SECTION 1: INTRODUCTION
1.1 Purpose of the Manual
This manual explains how to correctly install, operate, and get the best performance
from your RelaxWell Ocean Pod System. It may be used as a guide, suitable for all
levels of technical expertise, in determining and servicing mechanical and electrical
difficulties. This owner’s manual is organized as a quick reference guide. Any
additional updated or supplemental information for this reference guide may be
distributed to you as needed. Please read this owner's manual carefully before
installing your machine. Keep your manual near your machine for quick reference.
1.2 Customer Service
We welcome and appreciate your comments, questions, and suggestions in order to
continually offer the highest quality products, accessories, and services to our
customers. Our qualified professional teams are ready to assist you with a prompt
response to any question communicated to us by telephone, computer, and/or fax.
1.3 Disclaimer
While every attempt is made to ensure the accuracy and completeness of the
information in this document, some errors may exist. Sybaritic, Inc. does not accept
responsibility of any kind for customer loss due to use of or reliance upon this
document.
Sybaritic, Inc. reserves the right to make changes without notice in the product
described or contained herein in order to improve design and/or performance. Sybaritic,
Inc. assumes no responsibility or liability for the use of the product, conveys no license
or title under any patent, copyright or trademark right to this product or processes and
makes no representation or warranty that this product is free from patent, copyright or
trademark right infringement, unless otherwise specified. Applications that are
described herein for the product are for illustrative purposes only. Sybaritic, Inc. makes
no representation or warranty that such applications are suitable for the specified use
without further testing or modification.

Section 1 Introduction
RelaxWell Ocean Pod 2
1.4 Copyright
This manual is protected by copyrights. All rights are reserved. No part of this
publication may be reproduced, stored in a retrieval system or transmitted in any form or
by any means: electronic, mechanical, photocopying, recording or otherwise without the
prior written permission from the author and publisher. All inquiries should be
addressed to RelaxWell Ocean Pod System Owner’s, Installation, and Service Manual,
Sybaritic, Inc., at the headquarters address listed inside the front cover of this manual,
along with a date from a copy of the original purchase receipt of the RelaxWell Ocean
Pod System. No attempt has been made to designate as trademarks or service marks
all words or terms in which proprietary rights might exist. The inclusion, exclusion, or
definition of a word or term is not intended to affect, or to express a judgment on, the
validity or legal status of the word or term as a trademark, service mark, or other
proprietary term.

Section 2 Safety
RelaxWell Ocean Pod 3
SECTION 2: SAFETY
2.1 Preinstallation Technical Safety Tips
ATTENTION: WHEN RECEIVING A PACKED RELAXWELL OCEAN POD
SHIPMENT TRANSPORTED IN WINTER CONDITIONS (transportation temperature
below 32°F [0°C]), THE UNIT MUST BE STORED AT A ROOM TEMPERATURE
(conditions +59 to +86°F or +15 to +30°C, relative humidity max. 95%) FOR TWENTY-
FOUR HOURS TO BE WARMED UP BEFORE INSTALLATION AND OPERATION.
INSTALLING THE UNIT AND STARTING THE UNIT PREMATURELY (WITHOUT
PRIOR SLOW WARMING PERIOD) MAY RESULT IN SERIOUS DAMAGE TO THE
ELECTRONICS AND LCD PANEL OF THE UNIT.
ONLY A QUALIFIED/CERTIFIED/LICENSED ELECTRICIAN IS AUTHORIZED TO
MAKE THE ELECTRICAL CONNECTIONS STRICTLY ACCORDING TO ALL LOCAL
ELECTRICAL INSTALLATION REQUIREMENTS. ANY UNAUTHORIZED AND/OR
IMPROPER ELECTRICAL INSTALLATION IS STRICTLY FORBIDDEN. IN CASE OF
UNAUTHORIZED AND/OR IMPROPER INSTALLATION THIS UNIT MUST NOT BE
USED AND IT WILL RESULT IN WAIVE OF ANY TYPE OF MANUFACTURER’S
WARRANTY.
Only a qualified/certified/licensed plumber is authorized to make the plumbing
installation strictly according to all local plumbing installation requirements. ANY
UNAUTHORIZED AND/OR IMPROPER PLUMBING INSTALLATION IS STRICTLY
FORBIDDEN. IN CASE OF UNAUTHORIZED AND/OR IMPROPER INSTALLATION
THIS UNIT MUST NOT BE USED AND IT WILL RESULT IN WAIVE OF ANY TYPE OF
MANUFACTURERS’ WARRANTY.
THE USE AND OPERATION OF THE UNIT MUST BE CEASED IMMEDIATELY IF,
AFTER INSTALLATION, THE UNIT DOES NOT OPERATE PROPERLY.
BEFORE EVERY USE OF THE UNIT THE OPERATOR MUST BE SURE THAT
THE UNIT IS COMPLETE AND ALL PANELS AND/OR OTHER SUBPARTS ARE IN
PLACE.
2.2 General and User Safety
IN ORDER TO GUARANTEE FULL USER SAFETY THIS UNIT MUST BE
INSTALLED ACCORDING TO THE REQUIREMENTS OF THIS INSTALLATION
MANUAL AND IN COMPLIANCE WITH ALL LOCAL ELECTRICAL AND PLUMBING
REQUIREMENTS AND WITH OTHER APPLICABLE STANDARDS. (See the Electrical
Installation Requirements and Plumbing Installation Requirements in Section 4.)

Section 2 Safety
RelaxWell Ocean Pod 4
IN ORDER TO GUARANTEE FULL USER SAFETY AND REDUCE ANY TYPE OF
RISK FOR INJURY, THIS UNIT MUST AT ALL TIMES BE OPERATED UNDER THE
FULL SUPERVISION AND ASSISTANCE OF A TRAINED QUALIFIED ASSISTANT;
CHILDREN ARE PROHIBITED TO USE THIS UNIT WITHOUT A TRAINED,
QUALIFIED ASSISTANT.
PREGNANT WOMEN AND/OR PERSON HAVING A MEDICAL CONDITION
AND/OR USING MEDICATION, AND/OR HAVING ADVERSE MEDICAL HISTORY
SHOULD NOT USE THIS UNIT UNLESS RECOMMENDED BY A PHYSICIAN.
IN ORDER TO GUARANTEE USER SAFETY AND COMFORT, THIS UNIT MUST
BE TECHNICALLY INSPECTED DAILY AND THOROUGHLY CLEANED AND
DISINFECTED BEFORE EVERY USE. ALL UNIT OPERATIONS, TECHNICAL
INSPECTION, AND CLEANING MUST BE DONE BY TRAINED QUALIFIED
PERSONNEL.
2.3 Safety Precautions
Check the unit’s operating voltage before operation. It must be identical with that of
your local power supply.
When using any setting of Radiant Heat with the RelaxWell Ocean Pod System, be
sure to refrain from touching the upper portion of the inside of the cabinet. The
radiant emitters are located in this area and become very hot when the Radiant Heat
feature is in use.
Do not disassemble or modify the unit.
Prevent flammables and metallic objects from entering the unit.
Do not use the unit when there is lightning in the vicinity. Disconnect the power
cable of connected equipment.
Avoid using the unit under the following conditions:
Places subject to excessive shock or vibration.
Extremely hot places.
Use carefully. May cause burns.
Do not sit on top of the cover.
Do not sit on the unit when cover is only half open or closed.
Read this manual carefully before using the the RelaxWell Ocean Pod System.
NOTE: The rating plate (serial number plate) and safety caution of the main unit are
located at the base of the machine on the lower right leg.

Section 2 Safety
RelaxWell Ocean Pod 5
2.4 IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING –To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
DANGER –Risk of injury.
a) Replace damaged cord immediately;
b) Do not bury cord;
c) Connect to a grounded, grounding type receptacle only.
WARNING –For indoor use only. This unit is not intended for outdoor use.
WARNING –This product is provided with a ground-fault circuit-interrupter ( see
page 24). The GFCI must be tested before each use. With the product operating,
open the service door. Next push the reset button and close the service door. The
product should not operate. Now open the service door, push the reset button on the
GFCI and close the service door. The product should now operate normally. When
the product fails to operate in this manner, there is a ground current flowing
indicating the possibility of an electric shock. Disconnect the power until the fault has
been identified and corrected.
DANGER –Risk of Accidental Drowning. Extreme caution must be exercised to
prevent unauthorized access by children. To avoid accidents, ensure that children
cannot use this capsule unless they are supervised at all times.
DANGER –Risk of injury. The suction fittings in this capsule are sized to match the
specific water flow created by the pump. Should the need arise to replace the
suction fittings or the pump, be sure that the flow rates are compatible.
Never operate the capsule if the suction fittings are broken or missing. Never replace
the suction fitting with one rated less than the flow rate marked on the original
suction fitting.
DANGER –Risk of electric shock. Install at least 1,5 m (5 feet) from all metal
surfaces. As an alternative, a capsule may be installed within 1,5 m of metal
surfaces if each metal surface is permanently connected by a minimum 8,4 mm2 (8
AWG) solid copper conductor to the wire connector on the terminal box that is
provided for this purpose.
DANGER –Risk of electric shock. Do not permit any electric appliance, such as a
light, telephone, radio or television within 1,5 m (5 feet) of capsule.

Section 2 Safety
RelaxWell Ocean Pod 6
CAUTION –Test the ground fault circuit interrupter before each use of the spa
CAUTION –Adequate drainage must be provided if the equipment is to be installed
in a pit
CAUTION –Connect only to a circuit protected by a class a ground fault circuit
interrupter
WARNING –People with infectious diseases should not use a capsule.
WARNING –To avoid injury exercise care when entering or exiting the capsule.
WARNING –To not use a capsule immediately following strenuous exercise.
WARNING –Prolonged immersion in a capsule may be injurious to your health.
WARNING –Maintain water chemistry in accordance with manufacturer’s
instruction.
WARNING –To reduce the risk of injury:
a) The water in a capsule should never exceed 40˚C (104˚F). Water
temperatures between 38˚C (100˚F) and 40˚C are considered for a healthy
adult. Lower water temperatures are recommended for young children and
when capsule use exceeds 10 minutes.
b) Since excessive water temperatures have high potential for causing fetal
damage during the early months of pregnancy, pregnant of possibly
pregnant women should limit capsule water temperatures to 38˚C (100˚F).
c) Before entering a capsule, the user should measure the water temperature
with an accurate thermometer since the tolerance of water temperature-
regulating devices varies.
d) The use of alcohol, drugs or medication before or during capsule use may
lead to unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high
blood pressure, circulatory system problems or diabetes should consult a
physician before using the capsule.
f) Persons using medication should consult a physician before using capsule
since some medication may induce drowsiness while other medication may
affect heart rate, blood pressure and circulation.

Section 2 Safety
RelaxWell Ocean Pod 7
CAUTION –Risk of electric shock. Replace audio/video components only with
identical components.
Do not operate the audio/video controls while inside the capsule.
WARNING –Prevent electrocution. Do not connect any auxiliary components (for
example cable, additional speakers, headphones, additional audio/video
components etc.) to the system.
These units are not provided with an outdoor antenna; when provided it should be
installed in accordance with Article 810 of the National Electrical Code, ANSI/NFPA
70.
Do not service this product yourself as opening or removing covers may expose you
to dangerous voltage risk of injury. Refer all servicing to qualified service personnel.
When the power supply connections or power supply cord are damaged; if water is
entering the audio/video compartments or any electrical equipment component area;
if the protective shields of barriers are showing signs of deterioration; or if there are
signs of other potential damage to the unit, turn off the unit and refer servicing to a
qualified service personnel.
SAVE THESE INSTRUCTIONS

Section 3 Shipping, Storing, and Installation Conditions
RelaxWell Ocean Pod 8
SECTION 3: SHIPPING, STORING, AND
INSTALLATION CONDITIONS
3.1 Shipping, Storing, and Installation Conditions
This unit is designed for permanent indoor installation with the following conditions:
a. Temperature of the room: +59 to +86°F (+15 to +30°C). Relative humidity max.
85%.
b. Shipping conditions: temperature -4 to 104°F (–20 to + 40°C).
c. Storing conditions: temperature -4 to 104°F (–20 to +40°C). Relative humidity
max. 95%.
ATTENTION: WHEN RECEIVING A SHIPMENT TRANSPORTED IN WINTER
CONDITIONS (transportation temperature below 32°F [0°C]), THE UNIT MUST BE
STORED AT A ROOM TEMPERATURE (conditions +59 to +86°F [+15 to +30°C],
relative humidity max. 95%), FOR TWENTY-FOUR HOURS TO BE WARMED UP
BEFORE INSTALLATION AND OPERATION. INSTALLING THE UNIT AND
STARTING UP THE UNIT PREMATURELY (WITHOUT PRIOR SLOW WARMING
PERIOD) MAY RESULT IN SERIOUS DAMAGE TO THE ELECTRONICS AND
LCD PANEL OF THE UNIT.
The unit must be installed on an even, dry, solid floor surface and levelled.
The floor must have a central floor drain for the drainage connection and emergency
draining in order to avoid flooding (in case of plumbing failure).
It is best if the room has a separate ventilation system guaranteeing the sufficient
fresh air supply to the room.

Section 4 Electrical and Plumbing Requirements
RelaxWell Ocean Pod 9
SECTION 4: ELECTRICAL AND PLUMBING REQUIREMENTS
4.1 Electrical Installation Requirements
NOTE: Only a qualified/certified/licensed electrician is authorized to make the electrical
connections/installation of this unit strictly according to all local electrical installation
requirements. All local electrical installation requirements and loading value for one
phase must be observed when carrying out electrical installation/connections.
The unit’s power supply must be shut off prior to installation and/or any work on the
unit.
The RelaxWell Ocean Pod System should be used with AC 220-240, 50/60 Hz.
CAUTION: To prevent electric shocks and fire hazards, do NOT use any other
power source.
Because of the special nature of this device, an entire circuit needs to be dedicated
to the operation of the RelaxWell Ocean Pod System. Each individual RelaxWell
Ocean Pod System should have its own dedicated circuit breaker. The current draw
depends on the voltage and is rated at 13.41 amps for 220 volts when Radiant Heat
and Steam are running.
The unit is designed for use in current circuits where either a neutral conductor or a
stationary protective conductor with equivalent potential is available —system TN-S.
It is strictly prohibited to use the unit in alternating current circuits TT and IT.
Unit electrical specifications: 25A, 220V, 50/60Hz.
For electrical installation, the right hand side panel of the unit must be removed.
Place the unit on a level surface.
Make sure the cover can be opened without hitting the ceiling. Check the
SPECIFICATIONS SECTION for more details of the dimensions.
Do not install the unit near heat sources such as radiators, or in places subject to
excessive dust, mechanical vibration, shock, or heat.
Do not block the air inlet of the face fan located on top of the unit (hood).
If the unit is located in a cold location, the supporting hood strut may decrease
pressure in the strut chambers, which may cause the hood to drop sharply. The
operating temperature range for the struts is from 50 to 180°F or 15 to 80°C.
The unit must be connected to the electricity system stationary according to the
following:

Section 4 Electrical and Plumbing Requirements
RelaxWell Ocean Pod 10
4.2 Plumbing Installation Requirements
NOTE: Only a qualified/certified/licensed plumber is authorized to make the plumbing
installation strictly according to all local plumbing installation requirements.
The unit’s power supply must be shut off prior to installation and/or any work on the
unit.
For plumbing installation, the
right hand side panel of the unit
must be carefully removed.
After installation, the side panel
must be reinstalled before
operating the unit.
Minimum allowed water
pressure is 1.5 bars (21.75 psi) and maximum allowed water pressure is 4 bars (58
psi).
Pressure difference between cold and hot water supply must not exceed 2 bars (29
psi).
For normal over-body jet operation, the cold water must be between +50 to +59°F
(+10 to +15°C) and the hot water between +122 to +140°F (+50 to +60°C).
Cold water supplying the steam generator must have measured water hardness
below 71ppm USA (<4 PH German); if the water supply is harder, a water softener
must be installed for the steam generator.
The water supply for this unit must be mechanically cleaned/filtered. In order to
avoid damage to the unit subparts, nonsoluble, solid elements in the water supply
must be less than 50 microns. In order to guarantee that, it is necessary to install
mechanical water filters (50 micron filtering). Filters must have a flow rate of 2.5
gallons (9.5 liters) per minute.
All other water supply characteristics must meet the local drinking water
requirements.
Water supply connections in capsule are for ½” water inlets and the drain is 40mm.
BOTH THE COLD AND HOT WATER SUPPLY MUST HAVE SHUTOFF
(OPEN/CLOSE) VALVES THAT WOULD ENABLE REGULAR, EASY OPENING
AND CLOSING OF THE VALVES.
IN ORDER TO AVOID WATER SUPPLY PIPE BURSTS AND/OR FLOODING, THIS
UNIT MUST BE PROTECTED WITH COLD AND HOT WATER SHUTOFF
VALVES. SHUTOFF VALVES ENABLE THE OPERATOR TO CUT OFF THE
WATER SUPPLY WHEN THE UNIT IS NOT BEING OPERATED. THIS UNIT MUST
NOT BE CONNECTED TO THE WATER PRESSURE CONTINUOUSLY; THE
WATER SUPPLY MUST BE CUT OFF AT ALL TIMES WHEN NOT IN USE.
½” hot and cold lines should come from the floor or wall to the area where the unit is
to be placed. Connect them to the ½” male connections on the thermostatic mixing
valve on the right side of the unit.
Ensure that the water lines are purged of sand and grit prior to final connection to
the unit.

Section 4 Electrical and Plumbing Requirements
RelaxWell Ocean Pod 11
The capsule’s 1 ½” (40mm) O.D. drain should be spilled directly or indirectly into the
drain/floor sink.
RelaxWell Ocean Pod has a steam/shower system that utilizes approximately 64
gallons (240 liters) of water per 30-minute shower session.
Assume 40 gallons (150 liters) of this to be hot water.
Based upon the expected number of sessions daily, an appropriate hot water supply
needs to be installed.
The tub has a working capacity of approximately 60 gallons (220 liters) assuming a
50/50 mix of hot and cold water, this equates to approximately 30 gallons (110 liters)
of hot water per tub session.
The steam/shower system and the tub are used as separate sessions.
NOTE: Only a qualified/certified/licensed plumber is authorized to make the plumbing
installation strictly according to all local plumbing installation requirements.
4.3 Connecting To Oxygen System (Optional)
The Oxygen System can be used with any spa capsule to provide filtered, humidified
and/or oxygen-enriched air. To use in this manner, follow these simple installation and
operation instructions:
1. Place the Oxygen System upright on the floor within three to four feet of the foot
end of the capsule.
2. Connect oxygen administration tubing to air outlet on Oxygen System.
3. Locate the 02-IN tubing in right side under the foot area of the capsule as shown
on the images below.

Section 4 Electrical and Plumbing Requirements
RelaxWell Ocean Pod 12
4. Release the tube from the frame by removing the plastic strip. Locate the end of
the 02-IN tube and connect it with the Oxygen System.
5. Air Spray Brush tube can be connected to the hose connector located in the
head end of the unit (beneath the head rest area) as shown on the photo below.

Section 4 Electrical and Plumbing Requirements
RelaxWell Ocean Pod 13
6. 02 will flow into the capsule through the 02 nozzle on the hood in the foot area as
shown in the picture below.

Section 5 Installation Drawings
____________________________________________________________________________________
RelaxWell Ocean Pod 14
SECTION 5: INSTALLATION DRAWINGS
5.1 Removing Panels
BEFORE ANY REPAIR AND/OR INSPECTION OF THE UNIT, THE ELECTRICAL
SUPPLY MUST BE SHUT OFF.
BEFORE REMOVING THE SIDE PANEL OF THE UNIT, SHUT OFF THE
ELECTRICAL SUPPLY TO THE UNIT.
To remove the right side panel, remove screws S1, S2, S3, S5, S6, S7, S8 and S4
(S3 and S4 have two [2] screws on the opposite side panel).
5.2 Removing the Hood Cover
Remove two (2) screws and pull the cover in the direction of the arrow.

Section 5 Installation Drawings
____________________________________________________________________________________
RelaxWell Ocean Pod 15
5.3 Removing the Hood
To remove the hood, disconnect the wires from the valves in the hood.
Disconnect all cables and wires.
Disconnect water quick connections by pressing the opening ring, while at the same
time pulling the male end in the direction of the arrow.
To reconnect the quick connections, press the male portion of the fitting into the
female portion of the fitting.
Open capsule and unscrew strut nuts while keeping the capsule open.
Remove strut nuts and close capsule.
Remove hinge pins using a punch and hammer.