Sycamore 6000L User manual

© 2006, Sycamore SCS, LLC. - Rev. 1
PREFACE
Thank you for purchasing products from SYCAMORE SCS, LLC. We appreciate your business.
The following manual is only a guide to assist you and is not a complete or comprehensive manual of
all aspects of maintaining and repairing your generator. The equipment you have purchased is a
complex piece of machinery. We recommend that you consult with a dealer if you have doubts or
concerns as to your experience or ability to properly maintain or repair your equipment. You will
save time and avoid the inconvenience of having to go back to the store if you choose to write or call
us concerning missing parts, service questions, operating advice, and/or assembly questions. Our
gasoline generators have some of the following features:
•Lightweight construction
•Air cooled, four stroke gasoline internal combustion engine
•Recoil starter
•Large, spark arrestor muffler
•Circuit protector
•AC Outlets
•Low oil level sensor
Air-cooled gasoline generators are widely used when electrical power is scarce. Our generators
provide a portable solution in supplying power for field operations during project construction.
This manual will explain how to operate and service your generator set.
If you have any questions or suggestions about this manual, please contact your local dealer or us
directly. Consumers should notice that this manual might differ slightly from the actual
product as more improvements are made to our products. Some of the pictures in this manual
may differ slightly from the actual product as well.

6000 Watt Generator
© 2006, Sycamore SCS, LLC.
2
Table of Contents
Table of Contents.................................................................................................................................................2
Safety Guidelines – Definitions ............................................................................................................................4
Save These Important Safety Instructions! ..................................................................................................4
General Precautions ............................................................................................................................................5
Carbon Monoxide.........................................................................................................................................5
Gasoline and Oil...........................................................................................................................................5
Hot Components ..........................................................................................................................................6
Power Output ...............................................................................................................................................6
Work Area ....................................................................................................................................................6
Electrical Safety............................................................................................................................................ 7
Personal Safety............................................................................................................................................8
Generator Use and Care..............................................................................................................................9
Servicing.......................................................................................................................................................9
Heart Pacemakers........................................................................................................................................9
Installation..................................................................................................................................................10
Mechanical.................................................................................................................................................11
Chemicals...................................................................................................................................................11
Noise..........................................................................................................................................................12
Extension Cord...........................................................................................................................................12
Assembly............................................................................................................................................................13
Wheel and Handle Assembly.....................................................................................................................13
Wheel Assembly.........................................................................................................................................13
V-Leg Support Assembly............................................................................................................................13
Handle Assembly .......................................................................................................................................14
Specifications.....................................................................................................................................................15
General Parts Listing..........................................................................................................................................16
Figure A......................................................................................................................................................16
Generator Parts Listing......................................................................................................................................18
Figure B......................................................................................................................................................18

Owner's Manual
Panel Parts Listing.............................................................................................................................................19
Figure C......................................................................................................................................................19
Engine Parts Listing...........................................................................................................................................20
Figure D......................................................................................................................................................20
Figure E......................................................................................................................................................22
Figure F......................................................................................................................................................23
Figure G .....................................................................................................................................................24
Figure H......................................................................................................................................................25
Installation..........................................................................................................................................................27
General Location........................................................................................................................................27
Support and Mounting................................................................................................................................28
Grounding...................................................................................................................................................28
Operation ...........................................................................................................................................................29
Before Starting the Generator....................................................................................................................29
Starting.......................................................................................................................................................30
Powering 120 Volt AC Tools and Equipment:............................................................................................31
Inspection, Cleaning, and Maintenance.............................................................................................................32
Trouble Shooting................................................................................................................................................33
Wiring Diagram ..................................................................................................................................................34
Compliance........................................................................................................................................................35
Limited Warranty................................................................................................................................................36
_________________________________________________________________________________________
WARNING! READ AND UNDERSTAND ALL SAFETY PRECAUTIONS IN THIS MANUAL
BEFORE OPERATING. FAILURE TO COMPLY WITH INSTRUCTIONS IN THIS
MANUAL COULD RESULT IN PERSONAL INJURY, PROPERTY DAMAGE, AND/OR
VOIDING OF YOUR WARRANTY. SYCAMORE SCS WILL NOT BE LIABLE FOR ANY
DAMAGE BECAUSE OF FAILURE TO FOLLOW THESE INSTRUCTIONS.
© 2006, Sycamore SCS, LLC.
3

6000 Watt Generator
Safety Guidelines – Definitions
This manual contains important information that you need to know and understand in order to
ENSURE YOUR SAFETY and to PREVENT EQUIPMENT PROBLEMS. The following symbols help
you recognize this information. Please read the manual and pay attention to the notifications that
follow these symbols.
WARNING! WARNINGS INDICATE CERTAIN OR STRONG POSSIBILITY OF PERSONAL
INJURY OR DEATH IF INSTRUCTIONS ARE NOT FOLLOWED.
CAUTION: CAUTIONS INDICATE A POSSIBILITY OF EQUIPMENT DAMAGE IF
INSTRUCTIONS ARE NOT FOLLOWED.
Note: Notes give helpful information.
WARNING! IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD
RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND
ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.
WHEN USING POWER TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY.
Save These Important Safety Instructions!
Read and understand all of these safety instructions. Be sure to retain them for
future use.
© 2006, Sycamore SCS, LLC.
4

Owner's Manual
General Precautions
WARNING! FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE
INJURY OR DEATH.
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN ALSO RESULT IN
DAMAGE TO THE TOOL AND/OR THE ITEM YOU ARE WORKING ON.
Carbon Monoxide
When this tool is running, ensure that the area is well ventilated. Never run the
engine in an enclosed area without an exhaust evacuation system.
WARNING! THE EXHAUST CONTAINS POISONOUS CARBON MONOXIDE GAS THAT
CAN CAUSE LOSS OF CONSCIOUSNESS AND MAY LEAD TO DEATH. CARBON
MONOXIDE IS KNOWN TO CAUSE CANCER, BIRTH DEFECTS, AND OTHER
REPRODUCTIVE HARM.
Gasoline and Oil
This product requires oil and fuel. Attempting to start the engine without oil will ruin
the engine and void the warranty. Work in well ventilated areas. Keep cigarettes,
flames, or sparks away from the work area or where gasoline is stored.
WARNING! GASOLINE IS EXTREMELY FLAMMABLE AND IS EXPLOSIVE UNDER
CERTAIN CONDITIONS. KEEP OUT OF REACH OF CHILDREN.
•Gasoline fuel and fumes are flammable and potentially explosive. Use proper fuel storage and
handling procedures. Always have multiple ABC class fire extinguishers nearby.
•Keep the generator and surrounding area clean at all times.
•Fuel or oil spills must be cleaned up immediately. Dispose of fluids and cleaning materials as
per any local, state, or federal codes and regulations. Store oily rags in a covered metal
container.
•Never store fuel or other flammable materials near the generator.
•Do not smoke or allow sparks, flames, or other sources of ignition around the engine or fuel tank.
Fuel vapors are explosive.
•Keep grounded conductive objects such as tools away from exposed or live electrical parts and
connections to avoid sparking or arcing. These objects could ignite fumes or vapors.
•Do not refill the fuel tank while the engine is running or while the engine is still hot. Do not
operate a generator with known leaks in the fuel system.
•Use only the engine manufacturer’s recommended fuel and oil.
© 2006, Sycamore SCS, LLC.
5

6000 Watt Generator
General Precautions (cont'd)
Gasoline and Oil (cont'd)
•Excessive buildup of unburned fuel gases in the exhaust system can create a potentially
explosive condition. This buildup can occur after repeated failed start attempts, valve testing,
or hot engine shutdown. If this occurs, open exhaust system drain plugs and allow the gases to
dissipate before attempting to restart the generator.
Hot Components
WARNING! ENGINE AND EXHAUST SYSTEM PARTS BECOME VERY HOT AND
REMAIN HOT FOR SOME TIME AFTER ENGINE SHUT OFF. WEAR INSULATED
GLOVES OR WAIT UNTIL THE ENGINE AND EXHAUST SYSTEM HAVE COOLED
BEFORE HANDLING THESE PARTS.
Power Output
This generator is not designed to power sensitive electronic equipment (including computers and
medical devices) without the addition of an approved line conditioner, which is sold separately.
CAUTION: ATTEMPTING TO POWER SENSITIVE ELECTRONIC EQUIPMENT WITHOUT
THE USE OF AN APPROVED LINE CONDITIONER MAY CAUSE DAMAGE TO THE
EQUIPMENT. SYCAMORE SCS IS NOT RESPONSIBLE FOR ANY DIRECT OR
INDIRECT DAMAGE CAUSED BY FAILURE TO USE AN APPROVED LINE
CONDITIONER.
Work Area
•Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.
•Do not operate power tools in explosive environments such as in the presence of flammable
liquids, gases, or dust. Generators create sparks which may ignite dust or fumes.
•Keep bystanders, children, and visitors away while operating a generator. Provide barriers or
shields as needed.
© 2006, Sycamore SCS, LLC.
6

Owner's Manual
General Precautions (cont'd)
Electrical Safety
•Grounded tools must be plugged into an outlet, properly installed, and grounded in
accordance with all codes and ordinances. Never remove the grounding prong or
modify the plug in any way. Do not use any adapter plugs.
•Grounding provides a low-resistance path to carry electricity away from the user in the event of
an electrical malfunction.
•Double insulated tools are equipped with a polarized plug where one blade is wider than the
other. This plug fits into a polarized outlet in one way, only. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way. Double insulation eliminates the need
for a three-wire grounded power cord and a grounded power supply system.
•Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators.
There is an increased risk of electric shock if your body is grounded.
•Do not expose generator to rain or wet conditions. Water entering a generator will increase the
risk of electric shock.
•Do not abuse the power cord. Keep power cords away from heat, oil, sharp edges, or moving
parts. Replace damaged power cords immediately. Damaged power cords increase the risk
of electric shock.
•When operating a power tool outside, use outdoor extensions cords marked "W-A" or "W".
These extension cords are rated for outdoor use, and reduce the risk of electric shock.
•All connections and conduits from the generator to the load must be installed by trained and
licensed electricians, only. Installations must be in compliance with all relevant local, state,
and federal electrical codes and standards, and other regulations where applicable.
•For fixed installations, the generator must be earth-grounded before operation in accordance with
all relevant electrical codes and standards.
•Do not attempt to connect or disconnect wires to the load while standing in water or on wet or
soggy ground.
•Do not touch electrically energized parts of the generator and interconnecting cables or
conductors with any part of the body or with any non-insulated conductive object.
© 2006, Sycamore SCS, LLC.
7

6000 Watt Generator
General Precautions (cont'd)
Electrical Safety (cont'd)
•Before servicing equipment powered by the generator, disconnect the equipment from its power
input.
•Keep all electrical equipment clean and dry. Replace any wiring where the insulation is
cracked, cut, abraded, or otherwise degraded. Replace terminals that are worn, discolored, or
corroded. Keep terminals clean and tight.
•Insulate all connections and disconnected wires.
•Guard against electric shock. Prevent body contact with grounded surfaces such as pipes,
radiators, ranges, and refrigerators.
Personal Safety
•Stay alert. Watch what you are doing and use common sense when operating a
generator. Do not use a generator while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating generators may
result in serious personal injury.
•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
•Avoid accidental starting. Make sure the power switch is in its "STOP" position and disconnect
the spark plug wire when not in use.
•Remove adjusting keys or wrenches before turning on the generator. A wrench or a key that is
left attached to a rotating part of the generator may result in personal injury.
•Do not overreach. Keep proper footing and maintain balance at all times.
•Use safety equipment. Always wear eye protection. Wear ANSI approved safety impact eye
goggles. Dust masks, non-skid safety shoes, hard hats, or hearing protection must be used for
appropriate conditions.
•Do not overload the generator. Use the appropriate generator for your application. The
correct generator working at the rate for which it is designed, will do the job better and safer.
•Do not use the generator if the power switch does not turn the generator on or off. Any
generator that cannot be controlled by the power switch is dangerous and must be fixed or
replaced.
© 2006, Sycamore SCS, LLC.
8

Owner's Manual
General Precautions (cont'd)
Generator Use and Care
•Make sure the power switch is in its "STOP" position and disconnect the spark plug wire before
making any adjustments, changing any accessories, or storing the generator. Such preventive
safety measures reduce the risk of starting the generator accidentally.
•Store idle generators out of reach of children and other untrained persons. Generators are
dangerous in the hands of untrained users.
•Maintain generators with care. Do not use a damaged generator. Tag damaged generators
"DO NOT USE" until repaired.
•Check for misalignment or binding of moving parts, broken parts, and any other condition that
may affect the generator's operation. If damaged, have the generator serviced before using.
Many accidents are caused by poorly maintained generators.
•Use only accessories that are recommended by the manufacturer for your model. Accessories
that may be suitable for one generator may become hazardous when used on another.
Servicing
•Maintain labels and name plates on the generator and engine. These carry important
information. If unreadable or missing, contact SYCAMORE SCS immediately for a replacement.
•Generator servicing must be performed by qualified repair personnel only. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
•When servicing a generator, use only identical replacement parts and follow all appropriate
instructions in this manual. Use of unauthorized parts or failure to follow maintenance
instructions may create a risk of electric shock or injury.
Heart Pacemakers
WARNING! PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S)
BEFORE USING THIS PRODUCT. ELECTROMAGNETIC FIELDS IN CLOSE
PROXIMITY TO A HEART PACEMAKER COULD CAUSE INTERFERENCE TO OR
FAILURE OF THE PACEMAKER.
© 2006, Sycamore SCS, LLC.
9

6000 Watt Generator
© 2006, Sycamore SCS, LLC.
10
General Precautions (cont’d)
Installation
•Ensure installation meets all applicable local and national safety and electrical codes. Have
installation performed by a qualified licensed electrician or building contractor.
•All electrical work, including the earth-ground connection, should be completed by a licensed
electrician.
•Any separate fuel storage or generator supply facility must be built or installed in full compliance
with all relevant local, state, and federal regulations.
•It is recommended to use the generator only in well ventilated outdoor areas. A running
gasoline engine will generate carbon monoxide. This colorless and odorless gas can cause
serious injury or death if inhaled.
•If the generator is installed indoors, exhaust fumes must be piped out of the building using
leak-free and heat resistant piping. Pipes and soundproofing insulation should not use any
flammable materials nor should they be installed near any flammable objects. Generator
exhaust fumes must be within legal limits and installation must always meet local building codes.
•If the generator is installed outdoors, it must be weatherproofed and should be soundproofed.
It should not be run outdoors without adequate protection to the generator and wiring conduit.
•The generator weighs approximately 225 lbs. Without mechanical aid, lifting the generator off
the ground will require two or more people. Never lift the generator using any part of the
engine or alternator.
•Connect lifting equipment to the frame of the generator, only. Before lifting the generator with
equipment, ensure that the equipment and supporting structure are in good condition and are
rated to lift the intended load.
•Keep all personnel away from the suspended generator during relocation.
•The supporting floor or ground surface should be level and strong enough to safely hold the
weight of the generator. If the surface is not level, strong cross members should be placed
underneath the lower side of the generator frame. Ensure that cross members run the full
length of the generator frame.
•For trailer installation, the generator should be mounted in the middle of the trailer and over the
wheels. The trailer must be capable of supporting the weight of the generator, accessories,
and all contents (tools, etc.).
•Install weatherproofing and sound insulation only when it is not raining nor snowing to avoid
trapping moisture within the generator or within surrounding insulation.

Owner's Manual
© 2006, Sycamore SCS, LLC.
11
General Precautions (cont'd)
Mechanical
•Always make sure the power switch is in its "STOP" position. Disconnect the spark plug wire
and allow the engine to completely cool before carrying out maintenance.
•Check for damaged parts. Before using the generator, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for alignment and binding of moving parts, any broken parts or cracked mounting fixtures,
and any other condition that may affect proper operation.
•The generator is designed with safety guards for protection against contact with moving parts.
In any case, care must still be taken to protect personnel and equipment from other mechanical
hazards when working in the vicinity of the generator.
•Do not operate the generator without safety guards. While the generator is running, do not
attempt to reach around the safety guard for maintenance or any other reason.
•Keep hands, arms, long hair, loose clothing, and jewelry away from moving parts. Be aware
that when engine parts are moving fast they cannot be seen clearly.
•Keep access doors closed and locked when access to the generator is not required.
•When working on or in the vicinity the generator, always wear protective clothing including ANSI
approved safety gloves, safety eye goggles, and safety hats.
•Do not alter or adjust any part of the generator that is assembled and supplied by the
manufacturer.
•Always follow and complete scheduled engine and generator maintenance.
Chemicals
•Avoid contact with hot fuel, oil, exhaust fumes, and hot solid surfaces.
•Avoid body contact with fuels, oils, and lubricants used in the generator. If swallowed, seek
medical treatment immediately. If fuel is swallowed, do not induce vomiting. For skin contact
with fuel, immediately wash with soap and water. For eye contact with fuel, immediately flush
eyes with clean water and seek medical attention.

6000 Watt Generator
© 2006, Sycamore SCS, LLC.
12
General Precautions (cont'd)
Noise
Prolonged exposure to noise levels above 85 dB is hazardous to hearing. Always wear ANSI
approved ear protection when operating or working around the generator while it is running.
Extension Cord
If an extension cord (not included) is required, make sure to use only UL approved cords. Cords
should have the correct gauge and length according to the following table:
Cord Lengths
Nameplate Amps (@ full load) 0'·50' 50'·100' 100'·150' 150'·200'
0-5 16 16 12 12
5.1 - 8 16 14 10 -
8.1 - 12 14 12 - -
12.1 -15 12 10 - -
15 - 20 10 10 - -

Owner's Manual
© 2006, Sycamore SCS, LLC.
13
Assembly
Wheel and Handle Assembly
Confirm that the following sub-assembly components are included:
•1 Wheel Axle
•2 Heavy Duty Wheels
•4 Large Washers
•2 Cotter Pins
•1 Front Stand-off Support V-Leg
•2 Support V-Leg Mounting Screws
•1 Handle
•1 Handle Mounting Bracket
•1 Back Plate (Mounting Bracket)
•3 Hinge Bolt Mounting Nuts
•3 Three Inch Mounting Bolts
Wheel Assembly
Perform the following tasks to install the heavy duty wheels onto the generator assembly:
1. Insert axle through brackets located on the bottom cross bar of the frame.
2. Center axle in frame and place each wheel over each end of the axle, then insert axle end into the
hole located in the center of the wheel hub.
3. Place each large washer over the axle ends and insert axle through center of washer until washer
is flush against wheel hub.
4. Insert straight side of cotter pin into one of the holes located at both ends of the axle rod and
thread the cotter pin through the hole until pin snaps into place.
5. Repeat using the second cotter pin on the opposite end of the axle to secure the opposite wheel
to the axle assembly.
V-Leg Support Assembly
Perform the following tasks to install the V-leg support bracket:
1. Align V-leg support mounting holes with the mounting holes on the bottom of the frame.
2. Insert one mounting bolt completely through each mounting hole.
3. Twist mounting screws to catch the threads in the frame mounting holes and weld nuts and tighten
until support leg is secure.

6000 Watt Generator
© 2006, Sycamore SCS, LLC.
14
Assembly (cont'd)
Handle Assembly
Perform the following tasks to install the handle onto the generator frame:
1. On the side of frame with mounting holes, place back plate in the middle of handle bracket and
frame. Handle bracket should have handle mounting holes facing downward.
2. Align frame, back plate and handle bracket mounting holes.
3. Insert one mounting bolt through handle bracket, back plate, frame, and into mounting nut.
Twist mounting nut lightly.
4. Insert the second mounting bolt through the second mounting hole. Twist mounting nut until nut,
frame, back plate, and handle bracket surfaces are flush.
5. Return to first nut and tighten.
6. Align handle mounting holes with mounting holes on handle bracket.
7. Insert mounting bolt completely through handle and bracket.
8. Install a mounting nut onto bolt and tighten. Make sure handle can swivel.

Owner's Manual
© 2006, Sycamore SCS, LLC.
15
Specifications
Electrical
Current Output
120-240VAC @ 41.6/20.8A, 60Hz 12V DC
Continuous/Rated Wattage
5,000
Peak Wattage
6,000
Outlets four 120V 20A outlets
one 120V 30A twist lock outlet
one 120V/240V 30A twist lock outlet
one 12V DC outlet
Gasoline Engine
Horsepower
11HP
Type
4-cycle OHV air-cooled recoil start
Displacement
337cc
Oil Capacity
1.16 quart (1.1 liter)
EPA Approved
yes
Fuel
Type
unleaded gasoline
Capacity
5.5 gallons (21 liters)
Running Time
8 hours (approx.)
Fuel Gauge
included
Weight
Approximate Weight
224.4 lbs
Noise Level
Operating Noise Level
76 dB (approx.)

6000 Watt Generator
General Parts Listing
Figure A
This list is provided for reference purposes only. All repairs and part replacement should be
performed by a qualified technician. Some parts may not be available as single replacements.
© 2006, Sycamore SCS, LLC.
16

Owner's Manual
© 2006, Sycamore SCS, LLC.
17
General Parts Listing (cont’d)
Figure A (cont’d)
ITEM
NO. DESCRIPTION PSYCG # QTY.
ITEM
NO. DESCRIPTION PSYCG # QTY.
A01 ENGINE PSYCG6000LA01 1
A34 FRAME PSYCG6000LA34 1
A02 FLANGE PSYCG6000LA02 1
A35 RIGHT COVER PSYCG6000LA35 1
A03 SOCKET HEAD BOLT M10x25 PSYCG7000EA03 4
A36 SOCKET BOLT M8x55 PSYCG7000EA36 1
A04 HEX NUT M8 PSYCG7000EA04 4
A37 HANDLE PSYCG7000EA37 1
A05 SPRING WASHER Ø8.2xØ16 PSYCG7000EA05 4
A38 ACORN NUT M8 PSYCG7000EA38 3
A06 SOCKET HEAD BOLT M8x30 PSYCG7000EA06 4
A39 HANDLE BRACKET PSYCG6000LA39 1
A07 HEX BOLT M8x248 PSYCG6000LA07 1
A40 HEX SOCKET BOLT M8x50 PSYCG6000LA40 2
A08 BOWL WASHER Ø9 x Ø17.5 PSYCG7000EA08 1
A41 BACK PLATE PSYCG6000LA41 1
A09 SPRING WASHER Ø8.2 x Ø13 PSYCG7000EA16 1
A42 FLATE WASHER Ø8.2 x Ø13 PSYCG7000EA42 2
A10 ALTERNATOR PSYCG6000LA10 1
A43 TOP COVER PSYCG6000LA43 2
A11 FLANGED NUT M6 PSYCG7000EA11 3
A44 NUT FLANGED M6 PSYCG7000EA11 4
A12 FLANGED BOLT M6x12 PSYCG7000EA12 3
A45 BUSHING PSYCG7000EA45 4
A13 MUFFLER PSYCG6000LA13 1
A46 RUBBER GASKET PSYCG7000EA46 4
A14 DOUBLE SIDED M8x25 SCREW PSYCG7000EA14 2
A47 WASHER Ø6.6xØ22 PSYCG7000EA47 4
A15 HEX HUT M8x13 PSYCG7000EA15 2
A48 FLANGED BOLT M6x20 PSYCG7000EA48 4
A16 FLAT WASHER Ø8.2 x Ø813 PSYCG7000EA42 8
A49 FUEL TANK PSYCG7000EA49 1
A17 MUFFLER GASKET PSYCG7000EA17 2
A50 FILTER NET PSYCG7000EA50 1
A18 MUFFLER CONNECT PIPE PSYCG7000EA18 1
A51 FUEL TANK CAP GASKET PSYCG7000EA51 1
A19 RUBBER PAD PSYCG7000EA19 2
A52 FUEL TANK CAP PSYCG7000EA52 1
A20 FLANGED BOLT M8x14 PSYCG7000EA20 2
A53 FUEL GAUGE PSYCG7000EA53 1
A21 BOTTOM FOOT PSYCG6000LA21 1
A54 FUEL COCK PSYCG7000EA54 1
A22 FLANGED NUT M8 PSYCG7000EA22 2
A55 BACK COVER PSYCG6000LA55 1
A23 FRONT COVER PSYCG6000LA23 1
A56 LEFT COVER PSYCG6000LA56 1
A24 FLANGED BOLT M5x8 PSYCG7000EA24 24
A57 WHEEL PSYCG6000LA57 2
A25 HANDLE GRIP PSYCG7000EA71 1
A58 WASHER Ø16xØ30 PSYCG6000LA58 4
A26 MUFFLER INSULATION BOARD PSYCG7000EA69 1
A59 SPLIT PIN Ø3x25 PSYCG6000LA59 2
A27 HEX BOLT M10x40 PSYCG7000EA67 2
A60 AXLE PSYCG6000LA60 1
A28 ACORN NUT M610 PSYCG7000EA68 2
A61 FUEL TUBE PSYCG6000LA61 1
A29 ISOLATOR(RUBBER MOUNT) PSYCG7000EA29 4
A62 CLAMP PSYCG7000EA62 2
A30 HEX BOLT M10x25 PSYCG7000EA30 4
A63 SMALL FLANGED BOLT M6x8 PSYCG7000EA03 6
A31 WASHER Ø10.2 x Ø20 PSYCG7000EA31 12
A64 MUFFLER COVER PSYCG7000EA66 1
A32 SPRING WASHER Ø10.2 x Ø16 PSYCG7000EA32 8
A65 FLAT SCREW M6x10 PSYCG7000EA72 2
A33 HEX NUT M10 PSYCG7000EA03 8

6000 Watt Generator
Generator Parts Listing
Figure B
ITEM
NO. DESCRIPTION PSYCG # QTY.
ITEM
NO. DESCRIPTION PSYCG # QTY.
B01 COOLING FAN PSYCG7000EB01 1
B13 CAPACITOR SHELF PSYCG7000EB13 1
B02 ROTOR PSYCG6000LB02 1
B14 OVAL HEAD BOLT M5x8 PSYCG7000EB14 1
B03 DIODE PSYCG7000EB03 4
B15 CAPACITOR PSYCG6000LB15 1
B04 Ø32 WASHER PSYCG7000EB04 1
B16 CAPACITOR FASTENER PSYCG7000EB16 2
B05 Ø32 CLAMP PSYCG7000EB05 1
B17 ALTENATOR COVER PSYCG7000EB17 1
B06 BEARING PSYCG7000EB06 1
B18 OVAL HEAD BOLT M5x12 PSYCG7000EB18 4
B07 DRIVE END BRACKET PSYCG7000EB07 1
B19 RUBBER PAD PSYCG7000EB29 2
B08 ENCLOSING BAND PSYCG6000LB08 1
B20 GROUND PLATE PSYCG7000EB30 1
B09 STATOR PSYCG6000LB09 1
B21 OVAL HEAD BOLT M5x6 PSYCG7000EB31 1
B10 ALTERNATOR BACK COVER PSYCG7000EB10 1
B22 SPRING WASHER Ø8.2 PSYCG7000EA05 4
B11 HEX BOLT M8x210 PSYCG6000LB11 4
B23 DIODE FRAME PSYCG7000EB28 1
B12 WASHER Ø8.2 x Ø16 PSYCG7000EB12 4
© 2006, Sycamore SCS, LLC.
18

Owner's Manual
Panel Parts Listing
Figure C
ITEM
NO. DESCRIPTION PSYCG # QTY.
ITEM
NO. DESCRIPTION PSYCG # QTY.
C01 CIRCUIT BREAKER 20A WITH NUT PSYCG7000EC01 3
C13 GROUND BOLT M8x20 PSYCG7000EC18 4
C02 BREAKER 20A NUT PSYCG7000EC02 3
C14 4 PRONG SOCKET NEMA L14-30 PSYCG7000EC26 1
C03 OVAL HEAD BOLT ST4x10 PSYCG7000EC05 2
C15 WASHER Ø4.2 x Ø10 PSYCG7000EC24 8
C04 CIRCUIT BREAKER 25A WITH NUT PSYCG7000EC03 2
C16 SPRING WASHER Ø4.2 x Ø6 PSYCG7000EC23 8
C05 BREAKER 25A NUT PSYCG7000EC04 2
C17 HEX NUT M4 PSYCG7000EC22 8
C06 FLANGED BOLT M6x18 PSYCG7000EC10 4
C18 OVAL HEAD SCREW M4x12 PSYCG7000EC25 8
C07 FIBER WASHER Ø6.2 x Ø12 PSYCG7000EC32 4
C19 DUPLEX SOCKET NEMA 5-20 GFCI PSYCG2500LC10 2
C08 CONTROL PANEL PSYCG6000LC08 1
C20 3 PRONG SOCKET NEMA L5-30 PSYCG7000EC27 1
C09 STOP SWITCH PSYCG6000LC09 1
C21 CONTROL PANEL BOX PSYCG7000EC29 1
C10 DECORATIVE CUPREW NUT M8 PSYCG7000EC35 1
C22 OUTLET TRAP PSYCG7000EC30 1
C11 CUPREW WASHER Ø8.2 x Ø16 PSYCG7000EC37 3
C23 WIRING HARNESS PSYCG7000EC31 1
C12 HEX CUPREW NUT M8 PSYCG7000EC36 1
© 2006, Sycamore SCS, LLC.
19