Symmons ActivSense S6350B User manual

Dia ActivSense™
S6350B & S6350E
Sensor Lavatory Faucet
Operations and Maintenance Manual
Location:
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty
Installation Instructions
NUT
WASHER
GASKET NUT
WASHER
GASKET
NUT
WASHER
GASKET
Step 1 - Preperation for Mounting the Faucet
1. Shut o the water
supply
2. Remove the hex-
agonal nut, the disk,
and the gasket. Do
not remove the o-ring
from the base of the
faucet
Step 2 - Installing the Faucet
1. Optional: Place deck
plate through the holes
on the deck and secure
deck plate prior to fau-
cet installation
2. Place the faucet with o-ring into the hole in deck
lavatory. Make sure the o-ring is located between the
deck or lavatory and the bottom of the faucet.
3. Slide the gasket, disk, and hexagonal nut over the
flexible hose and secure the faucet into place.
4. Your faucet was supplied with a 0.5 GPM aerator
installed. Also, supplied is a 0.35 GPM and 1.0 GPM
aerators. If an alternate flow rate is required replace
the aerator and the housing. Please note the housing
is marked the the flow rate of the supplied aerator.

Installation Instructions
Step 3 - Connecting the Water Supply
1. Connect the flexible pipe to the water supply.
For models with temperature control connect the
red felxible pipe to the hot water supply and the
blue flexible to the cold water supply.
2. Turn on the central water supply and the shut-
o valves (angles vlave) and check for leaks)
Make sure that the filter(s) is/are install be-
tween the flexible pipe and the shut o valve
(angle valve) (not supplied).
Step 4 - Connecting the Power Source
Battery Version
Install the battery box underneath the sink with
the cable connection pointing down. The box can
be secured by inserting a screw into the wall and
hanging the box on it.
Transformer Version
Plug the transformer into an electrical outlet
and connect to the faucet.

DETECTION
RANGE
DELAY IN TIME
SECURIT Y TIME
COMFORT FLUSH
DELAY OUT TIME
TEMPORARY OFF
FUNCTION
RESET
HYGIENE FLUSH
Settings Adjustment
Adjusting the Setting with the Remote Control
If necessary, the sensor setting can be adjusted as following:
Shut o the water supply. in order to adjust the sensor with the remote control, hold the rre-
mote control straight in front of the sensor in a distance of about 6-8" (15-20cm). Choose the
function you want to adjust by pressing once on one of the function buttons. After pressing
once on a specific function button, a quick flashing of the LED at the front of the sensor will
occur. At this tage, you can change the setting by pressing the (+) or the (-) buttons, every push
will increase or decrease one level. After finishing the adjustment, turn the water supply back
on.
DETECTION RANGE: Only if necessary, use the remote control to adjust the
sensor range as follows:
Press the (RANGE) button Wait until a quick flashing of the LED in the sen-
sor eye is perceived. Then, press + to increase the one level and – to reduce
it every push will increase or decrease one level.
NOTE: Once you have changed the detection range with the remote con-
trol, this distance will be remembered by the sensor, even if the power
source is disconnected.

DELAY IN TIME: If required, the delay in time can also be modified as follows: Press the
IN button. Wait until a quick flashing of the LED in the sensor eye is perceived. Then,
press (+) to increase the delay in time and (–) to reduce it.
Settings Adjustment
DELAY OUT TIME: This button allows modifying the flushing start time after the user
moves away from the product. A delay out time close to 0 will save more water. An
increased delay out time will make the user experience more comfortable.
If required, the delay out time can be modified as follows:
Press the OUT button. Wait until a quick flashing of the LED in the sensor eye is per-
ceived. Then, press + to increase the delay out time and – to reduce it.
TEMPORARY OFF FUNCTION: This function is ideal to perform any kind of activity in
front of the sensor without operating the system (for example, cleaning).
The product will remain shut for minute when this button is pressed once. To cancel
this function and to return to normal operation press the (On/O) button again or wait
1 minute.
RESET BUTTON: This function restores all the factory settings except for the sensor
range. If required, press the Reset button and without releasing it, press the (+) button
once.
SECURITY TIME: The Security time, prevents continuous flushing of water due to
reflections or vandalism. By default, if the sensor is covered for more than 90 seconds
the water flow will shut automatically. To resume regular operation any obstruction
must be removed.
Press the (SEC) button. Wait until a quick flashing of the LED of the sensor eye is per-
ceived. Then, press (+) to increase the security time and (-) to reduce it.
24 HOUR HYGIENE FLUSH: This model includes a 24 hour hygiene flush which is dis-
abled. To activate the hygiene flush, press the (clock) button. Wait until a quick flash-
ing of the LED in the sensor eye is perceived. Then press (+) to activate the hygiene
flush. To disable it again, press (-) to deactivate it.
COMFORT FLUSH: If your model includes a comfort flush setting, it can be activated
by pressing the flush button.
When the button is pressed, one blink of the LED in the sensor eye is perceived. The
pre-programmed flush cycle will take place then. The comfort flush cannot be inter-
rupted or deactivated by pressing any button until it is over.
Maintenance
Filter cleaning instructions
This faucet is provided with one/two stainless steel filter(s) preventing forgein articles to enter the lines. If the water
flow has decreased, this can be because the filter(s) is/are clogged. The filter(s) can be cleaned as follows:
1. Shut-o the water shut o valve (angle valve).
2. Disconnect the flexible pipe/s.
3. Remove the filter(s) and wash it/them under running water.
4. Reassemble the parts.
5. Make sure that there is no water leakage.
Care and cleaning of chrome and special finishes
DO NOT use steel wool or cleansing agents containing alcohol, acid, abraisives, or the like. Use of any prohibited
cleaning or maintenance products or substances could damage the surface of the faucet. For surface cleaning of
faucet use ONLY soap and water, then wipe dry with clean cloth or towel. When cleaning bathroom tile, the faucets
should be protected from any splattering of harsh cleansers.

SD017
4-1/2 Foot Extension
SD019*
4 Inches
SD019*
4 Inches
SD017
4-1/2 Foot Extension
SD019*
4 Inches
SD019*
4 Inches
SD017
4-1/2 Foot Extension
SF277
9 Feet
(Sold separately)
SF278
120V Cable 4.5 feet long
Hard wired 15 Amp circuit.
(QTY:10) 12 Volt Outputs , 4.2A
Any combination of devices
10 devices maximum
(SF277 not inlcuded)
X10X10X10
SD017
(Optional Extension)
4-1/2 Foot Extension
SD019*
4 Inches
SD021*
AC Power Adapter
2 Devices - 1 Power Supply
*SD019 is required when powering a faucet from the SD021 power supply.
*SD019 is required when powering a faucet from the SD021 power supply.
6 Devices - 2 Power Suppply
10 Devices - 1 Power Supply
SD018
4 Inch male to male connector
required for S6350 faucet only
18”
One SD019 Splitter
included with power supply
One SD019 Splitter
included with power supply
One SD019 Splitter
included with power supply
6”
SD017
(Optional Extension)
4-1/2 Foot Extension
SF-281
AC Power Adapter
1 Devices - 1 Power Supply
39”
16 Feet
2-3/8”
SD021*
AC Power Adapter
SD021*
AC Power Adapter
Power Layout

Troubleshooting
SOLUTIONCAUSEINDICATORPROBLEM
Replace batteryLow battery
. Sensor flashes
continuously
when user’s
hands are within
the sensor’s
range
No water
coming out
of the faucet:
Increase the range by using the
remote
. Range is too short
. LED in the
sensor does not
flash once when
user’s hands
are within the
sensor’s range
Decrease the range by using the
remote
. Range is too long
The battery must be replaced
. Battery is completely used up
. Unit is in “Security Mode”*
Eliminate cause of reflection or
adjust sensor range
. Sensor is picking up reflections from the
washbasin or another object
Connect the electronic unit
connectors to the solenoid
. Connectors between the electronic unit and
solenoid are disconnecte
. LED in the
sensor flashes
once when
user’s hands
are within the
sensor’s range
Unscrew solenoid, pull out the
plunger and the spring from
the solenoid and clean them.
Use scale remover material if
needed. When replacing the
plunger, please make sure that
the spring is in vertical position.
. Debris or scale in solenoid
or the diaphragm is torn
Reduce the supply water
pressure
. The water supply pressure is higher than
PSI
and unscrew the inlet to the
solenoid to relieve the pressure
. The water supply pressure is under 8 bars and
yet the pressure in the faucet’s body is higher.
This situation could be caused by a sudden
increase in the water supply pressure that the
water supply pressure drops under 8 bars.
diaphragm
Debris or scale in diaphragm
. Sensor flashes
once when
user’s hands
are within the
sensor’s range
Water flow
from spout
does not
stop:
Clean or eliminate case of
interference
. Sensor is dirty or covered**
. LED in the
sensor does not
flash once when
user’s hands
are within the
sensor’s range
Decrease the range or eliminate
cause of reflection
. Sensor is picking up reflections from the
washbasin or another object
Remove, clean, re-installFilter or aerator is clogged
Water flow
diminished
Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2023 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3438 REV C ■ 100623