Tahtisaunat Moderni User manual

Installation manual: Tähtisaunat Moderni/Elegance/Original Opposite-Facing Benches.
Thank you for ordering a Tähtisaunat bench package! This manual contains installation instructions for the
opposite-facing benches of the Moderni, Elegance and Original models. In addition to the manual, Tähtisaunat
includes photos of the bench you are going to install. This will make your bench installation easier, because our
products are always custom-made. Below are some sample photos of the bench featured in this installation
manual. This manual is about the opposite-facing Moderni bench, but this manual is also suitable to use with
the Elegance and the Original models. It is recommended to oil the bench sections before installation, but only
when the final cleaning has been done. This manual includes photos of a few different benches, so that you
could have an overview of the most common set-ups within the same manual. We will never be able to provide
an entirely comprehensive manual, because every bench is custom-made, designed to be the perfect fit for every
customer's sauna.
For the installation, you will need at least a cordless drill or a screwdriver, TX20 Torx Power Bit, TX25 Torx
Power Bit, a spirit level, a 17 mm ring spanner, a tape measure, and a few hours of your time.
Finished photo:
Frame photo:
Installation stages:
1. The bench package includes two kinds of feet of different lengths, the longer of which support the upper bench, and
the shorter of which support the lower bench. First, attach the longer feet securely to the lower frame. The feet are usually

packaged to the front edge board of the lower bench, and your task is to position the feet according to the markings. On
the frame image included in the delivery, all feet have been marked as J1, J2, J3 etc. which helps to position the frames on
the correct locations. The frames can also be delivered assembled, depending on the delivery method. Connect the
elements of the lower frame to each other, and place the bench frame to the correct position in your sauna. Also place the
bench skirts in their correct positions, but do not screw them tight yet. The feet have markings for the bench skirt
attachment points.
2. Connect the solid frame parts of the lower bench to the lower bench frames. (On the sample frame image,
R4, R3 etc.) The screws will be tightened behind the lower bench frame. Do not screw the structure to the wall
yet. If your sauna has bench skirts like in the sample image, assemble and also install the end pieces to the front
foot frames. The attachment method largely depends on the measurements of the sauna, and can differ greatly
from what is seen on the image.

3. Lift the upper bench frames to their places. The upper bench is fitted to the metal pins on the feet by its lower
edges. We always leave a small installation allowance for the benches, which is usually 15 –20 mm. Install one
removable spacer to the lower bench. This helps you achieve the right gap to the front of the bench as well.
Centre the bench, and attach the upper bench frames to the walls (90 mm screws, included in the delivery!),
straight through the frame, screwed to the same bar that the panel is attached to. If it looks like there is going to
be a large gap behind the structure, stuff the gaps next to/on top of the screw with plywood patches, which are
included in the delivery. The nailing board can usually be located by checking where the panel has been nailed
to the wall. If no nails are visible, use your hand to try where the trim is located beneath the panel. Use the spirit
level to help you install the benches straight. When the frame has been fastened to the wall, screw the bench
skirts properly in position, and lift the tops of the upper bench to their position. The bench tops are not fastened
to the frames. Also check the straightness depth-wise.
4. Place the backrests in position. The installation height is usually 400 mm –450 mm, depending on the model
and the material. This height can be raised or lowered according to your own preference. Also consider the
windows! Use the window to check the installation height, if the window is positioned low in the sauna! Check
the straightness with a spirit level. (Screws 55 mm long, included in the delivery!)

5. Place the spacers of the lower bench in position. If the spacer is on top of the joist hanger, it does not have to
be fastened with screws. The joist hanger solution makes sauna cleaning easier, when you can simply lift the
frames out of the way during cleaning. PLEASE NOTE! If the solid frames by the walls are long (more than
600 mm), screw them also to the walls, in the same way as the upper benches. Check the straightness with a
spirit level and adjust with the levelling feet.
6. Lift the bench tops to their places. The bench tops are not fastened to the frames. If the sauna stove is
integrated through the lower bench, centre it in its correct position during this stage. If the sauna is designed to
have a sauna stove railing that rests on the lower bench, place that in position too. The tops of the lower bench
have holes for the metal pins in the railing feet, and the railing is installed according to these.

7. Put the footstool in its place; the installation is now complete. Levelling feet on the feet of the footstool in the
Moderni and Elegance model. Also remember to put anti-slip guards on the front levelling feet (included in the
delivery).
In case of any problems, you can contact our production department on [e-mail]