Taicom V1103D User manual

Load Balance Broadband Router
User’s Manual
V1103D

2
Table of Contents
CHAPTER 1. INTRODUCTIONS
1.1 About Load Balance Router. ………………………….5
1.2 Interface. ………………………………….……………5
1.3 Package. …………………………………………………5
CHAPTER 2. ROUTER INTRODUCTION
2.1. 4* WAN Ports Broadband Router
2.1.1. Front Panel View………..………………..……...6
2.1.2. Real Panel View……………………………………….6
2.1.3. LED Indicator…………………………….…….……..7
2.2. 2 *WAN Ports Broadband Router
2.2.1. Front Panel View…………………………….…...…..8
2.2.2. Real Panel View………………………………….……8.
2.2.3. LED Indicator…………………………………….…..9
2.3. Broadband Router Features
2.3.1. Software Feature…………………………………..…9
2.3.2 Factory Default Value……………………………..…11
2.3.3. How to configure router…………………………….12
.
CHAPTER 3. CONNECT ROUTER
3.1. Connection Diagram………………………………….……13
3.2. Connection Procedure………………………………...….14
CHAPTER 4. PREPRE COMPUTER TCP/IP
ENVIRONMENT
4.1 Windows 95/98/ME……………………………………….15
4.2 Windows 2000/XP.…………………………..……….….24
CHAPTER 5. CONFIGURE ROUTER
5.1 Administration

3
5.1.1 Log on……………………………………….…...33
5.1.2 Change Password……………………………....33
5.1.3 Load Factory Default……………………………34
5.2 Work Mode……………………………………………. 35
5.3 System Status
5.3.1 Link Status…………………………………….….37
5.3.2 Data Monitor……………………………….…...38
5.4 WAN Configuration
Configure WAN1/WAN2/WAN3/WAN4
5.4.1 Dynamic IP/CABLE Type………………….…..43
5.4.2 PPPoE /Dial Up DSL Type………………….…43
(Gateway, Basic NAT Mode only).
5.4.3 Static IP /Leased DSL Type……………………44
5.5 Bandwidth Usage Control……….…………………..46
5.6 Configure LAN&DHCP………………..………....48
5.7 Routing Table
5.7.1 Configure………………………………….….…51
- Static Routing
- Dynamic Routing
5.7.2 Current Routing Table………….………….…53
5.8 Access Control
5.8.1 Local IP Filtering (Gateway Mode only)…….54
5.8.2 Remote IP Filtering (Gateway Mode only)..…57
5.8.3 DoS Defense
(Gateway Mode only)…………...57
5.9 Advance
5.9.1 Virtual Server (Gateway, Basic NAT Mode only)..…...61
5.9.2 DMZ Host
(Gateway, Basic NAT Mode only )………..63
5.9.3 Multi-NAT
(Gateway, Basic NAT Mode only) ….….…65
5.9.4 Load Balance (Gateway, Basic NAT Mode only)…....66
5.9.5 IP Binding
(Gateway, Basic NAT Mode only)…….….69
5.9.6 DDNS (Gateway, Basic NAT Mode only)……………..71
5.9.7 Configure Proxy
(Gateway, Basic NAT Mode only)....72
5.9.8 Mail Alert (Gateway, Basic NAT Mode only)..…..…. 73
5.9.9 Time Zone (All Mode)……………………….….…...75.
5.9.10 System Log
(All Mode)…………………….………..76
5.9.11 Mac Address Clone
(All Mode)………….……..….77
5.10 Firmware Update………………………………..…..……..81
5.11 Save &Reset……………………………….……….……….87

4
CHAPTER 6. HARDWARE LOAD DEFAULT …88
CHAPTER 7. ROUTER SPECIFICATION...….…89
CHAPTER 8. APPENDIX
8.1 TCP/IP Protocol Port Number List………………....93
8.2 Configuration Examples
EXAMPLE 1. LOAD BALANCE……………………….….…94
EXAMPLE 2. LOAD BALANCE...…………………….…....95

5
Table of Contents
CHAPTER 1. INTRODUCTIONS
1.1 About Load Balance Router
Load Balance Router also called Multi-Homing SOHO Gateway or
Multi-Homing Ethernet Router and so forth. It provides 2/4 10/100 Mbps
Ethernet ports (WAN port) and one 10/100 Mbps Ethernet port (LAN port).
WAN port is using to connect to broadband transmission equipments such as
ADSL modem or CABLE modem for user and far end to download or upload
data in high speed. Broadband Router provides one LAN port to connect to
computer via cable. You can also connect LAN port with HUB/SWITCH device
to extend the amount of connection device/user if necessary. Families with
multiple PCs could share one ISP account and play exciting games against
each other through Broadband Router. The switch function could also reduce
the traffic in internal LAN.
Load Balance Broadband Router allows multi-user to use with single user
account at the same time. And it is easy to configure and easy to use. In
addition, it also provides you some special applications, such as FTP, HTTP,
Mail and Telnet exclusive server on your LAN. DMZ (Demilitarized Zone)
function (see this manual for details), IP filtering and SPI (Stateful Packet
Inspection) can ensure the security of your Host and data. With its built-in
Internet gateway capability, resource sharing is now faster and easier.
With Load Balance function, Broadband Router not only provide rich
software feature as describe above, via built in 2 WAN/4 WAN port in this
equipment, user can enjoy traffic load sharing & load balance of Multiple
ADSL/Cable link, In order to avoid single link failure risk.
1.2 Interface
 2 * 10/100Mbps WAN ports, RJ45, auto sensing (2 WAN Router)
 4 * 10/100Mbps WAN ports, RJ45, auto sensing (4 WAN Router)
 1 * 10/100Mbps LAN port, RJ45, auto sensing
 DC input 5V/2A
 Default Switch (load factory default)
 FG (Frame Ground)
1.3 Package
 1 * Broadband Router (2 WAN or 4 WAN)
 1 * CD-ROM containing Broadband Router user’s manual
 1 * AC Adapter suitable for your electric service
 1 * Network cable with RJ-45 connectors for LAN connection
When you open your package, make sure all of the above items are
included and not damaged. If you see that any components are damaged,
please notify your dealer immediately.

6
CHAPTER 2 ROUTER INTRODUCTION
2.1. 4 *WAN Ports Broadband Router
2.1.1 Front Panel View
2.1.2 Real Panel View
DefaultLAN
DC INPUTFG
DC 5V/2A
WAN
4
2
1
3
LAN
WAN 1
WAN 2
WAN 3
WAN 4
B
roadband Route
r

7
FG: Ground connection.
DC 5V: Connecting to AC adapter.
WAN: Broadband Router provides four RJ45 type WAN port connecting to
broadband transmission equipments such as ADSL or CABLE Modem via
RJ45 cable.
LAN: Broadband Router provides one RJ45 type LAN port connecting to your
network devices such as Hub/Switch via RJ45 cable. Using a HUB/Switch will
allow more PC connecting to Broadband Router.
Default: If Broadband Router occurs any system crash, you may press this
button to reload factory default value.
2.1.3 LED Indicator
LEDs Indication
Off Disconnected or undetected
Green Linked
Green Flash Data Transmission
WAN1~4
Red Collision
Green Link 100M
Green Flash 100Mbps Data Transmission
Off Disconnected or undetected
Orange Link 10M
LAN
Orange Flash 10M Data Transmission

8
2.2. 2 *WAN Ports Broadband Router
2.2.1 Front Panel View
2.2.2 Real Panel View
DefaultLAN
DC INPUTFG
DC 5V/2A
WAN 2
1
LAN
WAN 1
WAN 2
POWE
R
ALARM
B
roadband Route
r

9
FG: Ground connection.
DC 5V: Connecting to AC adapter.
WAN: Broadband Router provides two RJ45 type WAN port connecting to
broadband transmission equipments such as ADSL or CABLE Modem via
RJ45 cable.
LAN: Broadband Router provides one RJ45 type LAN port connecting to your
network devices such as Hub/Switch via RJ45 cable. Using a HUB/Switch will
allow more PC connecting to Broadband Router.
Default: If Broadband Router occurs any system crash, you may press this
button to reload factory default value.
2.2.3 LED Indicator
LEDs Indication
Off Disconnected or undetected
Green Linked
Green Flash Data Transmission
WAN1~2
Red Collision
Green Link 100M
Green Flash 100Mbps Data Transmission
Off Disconnected or undetected
Orange Link 10M
LAN
Orange Flash 10M Data Transmission
POWER Green Power on
ALARM Red Router crash
2.3 Broadband Router Features
2.3.1 Software Feature
In order to meet different application usage, you can configure this router
to be 3 different working model.
.Gateway mode
. Router mode
. Basic NAT mode

10
Each working mode include different features
Function
Mode
LAN to WAN
Through put NAT
Function DMZ, Dos
Virtual Ser
IP Filtering
IP
Domain PPPoe Dial up
Gateway
Mode Good
DoS on: 31 M
DoS off: 38 M
Yes Yes Legal
To
Illegal
Yes
Router
Mode Best
~90M bps No No.... (1) Legal To
Legal (4)
No
Basic NAT
Mode (2) Good
~48M bps Yes Yes…(3) Legal To
Illegal
Yes
(1) All NAT related function will be disable
(2) The purpose for this mode is to have high through-put and NAT function
both
(3) Simple NAT function available
(4) Act like a multi-LAN port router
Working Mode / Function List
Mode
Function Gateway Router Basic NAT
PPPoE/
Dial Up DSL Type V V
Local IP Filtering V
Remote IP Filtering V
Dos Defense V
Virtual Server V V
DMZ Host V V
Multi-NAT V V
Load Balance V V
Dynamic DNS V V
Mail Alert V V
Time Zone V V V
System Log V V V
Mac Address Clone V V V
Configure Proxy V V
Routing protocol V V V
DOD (PPPoE) V V
IP Binding V V
Bandwidth Usage
Control V V

11
2.3.2 Factory Default Value
Value
Function Default Enable Disable
Gateway V
Router
Work Mode
Basic NAT
Link Status VSystem
Status Data Monitor V
Connect to Internet
Health Check V
WAN Type Dynamic IP
WAN
Configure
Schedule V
Bandwidth
Usage
Control V
Configure
LAN & DHCP DHCP server V
Static Route VRouting
Table Dynamic
Route V
Local IP
Filtering V
Remote IP
Filtering V
Access
Control
DoS Defense V
(Some items)
Virtual Server V
DMZ Host V
Multi-NAT V
Load Balance Session
IP Binding V
DDNS V
Proxy V
Mail Alert V
Advance
Time Zone V
AdministrationLoad default V
Save & Reset V

12
2.3.3 How to configure router
This equipment provide 3 working mode for different usage, in order to
set proper parameter in each function/mode, you can follow this flow chart
before you start to configure router.
START poweronROUTER
Iconnect LAN cable to PC
IsettingPCenvironment
I (Chapter3,4)
I
LOG ON .UN=admin,PW=admin
I (Chapter5-1,5-2)
I
Click select working mode
WORK MODE default is Gateway mode
I (Chapter5-3)
I
I
SELECT MODE ROUTER will reboot after
Iselect
I
_______________________________________________
Gateway Basic NAT Router
________I________________ _ I_ _I_
IIIII
Access Bandwidth Advance Advance Advance
Control Control
---- ---- ---- ----
LocalIPFiltering Virtualserver Virtualserver
RemoteIPFiltering DMZHost DMZHost
DosDefense Multi-NAT Multi-NAT
Load Balance Load Balance
DDNS DDNS
Proxy Proxy
MailAlert MailAlert
Time Time Time
System Log System Log System Log
Mac address Mac address .Mac address
Clone Clone Clone
IPBinding IPBinding
I
I
_____________________________________________________________________
System Configure WAN Administration F/WUpdate
Status LAN & DHCP Configuration
I
I
I
SAVE & RESET

13
CHAPTER 3. CONNECT ROUTER
3.1 Connection Diagram
Broadband Router provides one LAN port connecting to your network
devices such as PC, HUB and SWITCH via RJ45 cable. Using a
HUB/SWITCH will allow more PC connecting to Broadband Router. WAN
ports are using to connect your ADSL or CABLE Modem to the broadband
ISP.
For RJ45 cable type, both WAN/LAN port support auto MDI/MDIX
Function, you can choose cross over type or straight type RJ-45 cable
Defaul
t
LAN
DC INPUT
FG
D
C
5V/
2A
WAN
HUB/SWIT
ADSL/CABL
ADSL/CABL
ISP
INTERNET

14
3.2 Connection Procedure
1. Plug in DC power adapter to Router.
2. Connect the Router WAN port RJ45 modular jack to ADSL/CABLE
Modem Ethernet port with the RJ45 cable.
3. Connect the Router LAN port RJ45 modular jack to HUB/SWITCH
LAN port with the RJ45 cable.
4. Connect PC LAN card port to HUB/SWITCH LAN port.
5. Connect FG to ground
6. Plug in AC power cord to power source
7. Go to Chapter 2. section, 2.3.3 How to configure router.

15
CHAPTER 4. PREPARE COMPUTER TCP/IP
ENVIRONMENT
4 .1 Windows 95/98/ME
1. Select Control Panel from StartSettings.
2. Double click Network icon.

16
3. Select TCP/IP->xxxx, where xxxx is the name of network adapter you are
using and then click Properties.
4. Verify your IP Address option is at Obtain an IP address automatically.

17
5. Let your Gateway setting remain empty.

18
6. Verify your DNS Configuration option is at Disable DNS, The Broadband
Router will assign it automatically, then click OK. But also you may select
Enable DNS, then key in the value manually if you preferred.
7. Select Run item from Start menu. Type in winipcfg and then click OK.

19
8. Select the network adapter you are using from pull-down list. Click Release
All and then Renew All to get the information about IP Address, Subnet
Mask, and default Gateway that Broadband Router gained. Then click OK.
9. You must uncheck the Proxy server function before login the web
configuration. The way of uncheck the Proxy server in Internet Explorer and
Netscape is described as follow.

20
Internet Explorer
• Highlight Internet Explorer on desktop and then right-click your
mouse to select Properties.
• Select LAN Settings in Connections tab.