Talos Security DV1080VIR24 User manual

DIMENSION
Dimensions
*** Above specifications can be subject to change without previous notice***
920g
144mm (W) x 107mm (H) x 144mm(W)
Items Submenu
DV1080VIR24
CMOS
Device 1/3” 2MEGA CMOS
Total 2010 (H) x 1108(V)
Effective
1944 (H) x 1092(V)
Performance
Resolution Digital : 1080P(30p) , 720P(60P)
Max : 1,100TV lines(1080P)
Scanning system
Progressive
Minimum illumination(F1.2) Color : 0.1Lux(50IRE)
B/W : 0.08Lux(50IRE)
S/N Ratio More than 50dB (AGC off)
Functions
OSDEnglish/Japanese/German/Italian
Russian/Spanish/Chinese/Portuguese
Day&Night
Auto/Day/B&W/EXT1/EXT2
ATW
1800 ~ 10500K
High Speed Shutter 1/30(1/25) ~ 1/60Ksec
WDR
2 ~ 4
D-WDR
Off/ON
BLC Off/ON (Size, Position)
HLC Level Setting(0~20), Color
AGCLevel Setting(0~10)
D-Zoom 0~96 Steps
Camera ID
Off/On (Letters A to Z, Numerals 0 to 9, Symbols)
White Balance
AUTO / AUTOext / PUSH / MANUAL
DNR 3DNR, OFF/LOW/MIDDLE/HIGH
Motion Detection Off/ON
Privacy Mask
32 Areas (On/Off, Color, Position)
Sens-Up
x2 ~ x4
Etc. Function
Sharpness, Reverse(H,V) Etc. Function
ColorBar
Off/ON
In/OutputAlarm Output
Video Output
Visible Range
(LED On)
Hardware
ANALOGUE
NTSC, PAL CVBS(without WDR)
HD-SDI(SMA CONNECTOR)
Video Output
Power Consumption
Lens
Indoor
Outdoor
DC 12V/ 24 AC, Less than 2.2Watts
2.8~12mm DC Auto IRIS VF Lens
Built-In 24 IR Leds(20M of Viewing Distance)
Built-In 24 IR Leds(10M of Viewing Diatance)
Operating Temperature
Absolute : - 10C ~ +50C
Operating Humidity
Dimension
Weight
Less than 90%
FRONT
107
144
56
TOP
User Manual
DV1080VIR24
talossecurity.com

INSTALLATION
1
5687
234
Mount Base
Lock
Open
Camera
Insert
“L” Wrench
“L” Wrench
Wrench Screw
Fixing Screw
Camera
Gimbal
Gimbal Cap
OSD
Controller Safety
Cable
Video
test Port
Cover
Ring
Fix the mount base onto the ceiling
or wall by the fixing screw and insert
the camera like the arrow direction.
Open the bubble cap and move the camera gimbal
to left, right and up, down to set the viewing direction.
After set the viewing direction, open the gimbal cap
like the arrow diection snd adjust the viewing angle.
Set the desired OSD feature by using the OSD controller.
(Refer the SOD manual to set up the desired OSD)
in case of a installer has portable monitor, connect the
video jack to the video test port to set up the OSD.
Tighten the screw by using the “L”wrench
and complete the installation.
Close the dome cover just like above
Fig7 to tighten the screw.
After insert the camera body to the mount base
like the Fig1 and slide the camera body just like
the Fig2 to fix the camera onto the base.
Fix the screw into screw hole in the mount-
base by using the “L”wrench and tighten
the camera body onto the base.
Unscrew the cover ring screw by
using the “L”wrench and open
the cover ring.
Mount Base
Mount Base
Camera Body Camera Body
“L” Wrench
Cover
Ring