Tamarack Solar TTP-A-2 User manual

Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Installation Manual
Models: TTP-A-2 / TTP-A-3 / TTP-A-4 / TTP-A-4HW / TTP-A-6 / TTP-A-6HW
TTP-A-MAN v2
Note: 2-inch horizontal steel pipes shown in the pictures above are not included. Purchase locally or from us.
TTP-A-2 2 Module Top of Pole Mount
TTP-A-3 3 Module Top of Pole Mount
TTP-A-4 4 Module Top of Pole Mount
TTP-A-4HW 4 Module Top of Pole Mount, High Wind
TTP-A-6 6 Module Top of Pole Mount
TTP-A-6HW 6 Module Top of Pole Mount, High Wind

2
Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Scan the QR Code below to see an animated video of the assembly of this mount.
Technical Support: 707-234-8107 or 800-819-7236 Ext 556
Use these torque sengs when assembling your TTP-A mount.
If you are using an-seize compound on bolts, reduce torque by 15%.
Bolt Description Bolt Size Socket Size Foot-Lbs
Cap Bolts 3/4-inch 1-1/8 inch 100
Cap Set Screws 1/2-inch 1/2-inch 8pt 40
U-Bolt on Adjuster 3/8-inch 9/16-inch 12
Hex Bolt on Adjuster 1/2-inch 3/4-inch 40
H-Frame Bolts 1/2-inch 3/4-inch 45
U-Bolts Pipe to H-Frame 3/8-inch 9/16-inch 15
U-Bolts on Pipe Mounts 5/16-inch 1/2-inch 6
Rail Splice Bolts 5/16-inch 1/2-inch 12
Pipe Mounts on rails 5/16-inch 1/2-inch 12
5050 Mid Clamps on Modules 5/16-inch 1/2-inch 12
5050 Clamps as End Clamps 5/16-inch 1/2-inch 9
TTP-A Torque Settings

Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Disclaimer
This manual describes proper installaon procedures and provides necessary standards required for product
reliability. Warranty details are available on our website. www.tamaracksolar.com
All installers must thoroughly read this manual and have a clear understanding of the installaon procedures
prior to installaon. Failure to follow these guidelines may result in property damage, bodily injury or even
death.
Structural parts of this mount are made with painted steel which will show signs of rust in areas that get
scratched during assembly. It is good pracce to repaint scratched parts aer assembly.
Installer Responsibilies
• Follow all applicable local or naonal building and re codes, including any that may supersede this
manual.
• Electrical installaon should be conducted by a licensed and bonded electrician or solar contractor.
• Module maintenance or removal must not break the bonding path of the system.
• Ensure all products used are appropriate for the installaon and array under the site’s loading condions.
• Use only Tamarack parts or parts approved by Tamarack; substung parts may void any applicable
warranty.
• Comply with all applicable re codes including, but not limited to, keeping walkways clear.
• Ensure bare copper grounding wire does not contact aluminum and zinc-plated steel components, to
prevent risk of galvanic corrosion.
• If loose components or loose fasteners are found during periodic inspecon, reghten immediately. If
corrosion is found, replace aected components immediately.
• Provide an appropriate method of direct-to-earth grounding according to the latest edion of the Naonal
Electrical Code, including NEC 250: Grounding and Bonding, NEC 690: Solar Photovoltaic Systems, and CSA
C22.1, Safety Standard for Electrical Installaons, Canadian Electrical Code, Part 1
• Disconnect AC power before servicing or removing microinverters and power opmizers.
• Review module manufacturer’s documentaon to ensure compability and compliance with warranty
terms and condions.
• Maximum Series Fuse Rang is 20 Amps.
Tools Required
• 1 1/8-inch Socket
• 1-1/8-inch Wrench
• 3/4-inch Socket
• 9/16-inch Socket
• 1/2-inch Socket
• Ratchet to t Sockets
• Crescent Wrench
• Torque Wrenches (sengs range from 6 to
100 foot-pounds. This may require mulple
wrenches)
• Tape Measure
• Angle Finder
• Compass
• Ladder

4
Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
TTP-A Series Pole Mount Components
Part Description TTP-A-2 TTP-A-3 TTP-A-4 TTP-A-4HW TTP-A-6 TTP-A-6HW
Pole Cap, Pivot 4-inch pipe, 2.5-inch holes 1 1
Pole Cap 4-inch Backplate 1 1
Array Tilt Adjuster Arm 1 1
Pole Top Cover 4-inch 1 1
Pole Cap Bolts 3/4 -10 x 7-inch 1 1
Pole Cap Top Support Bolt 3/4-10 x 6-inch 1 1
Pole Cap FlangeNut 3/4-10 1 1
Set Bolts 1/2 -13 x 1-1/2inch 1 1
Hex Bolt 1/2-13 x 1-1/2-inch for Adjuster 1 1
Flange Nut ½ - 13 for Adjuster 1 1
Adjuster U-Bolt ⅜” x 2-1/2-inch 1 1
Pole Cap, Pivot 6-inch pipe, 2.5-inch holes 1 1 1 1
Pole Cap 6-inch Backplate 1 1 1 1
Array Tilt Adjuster Arm 1 1 1 1
Pole Top Cover 6-inch 1 1 1 1
Pole Cap Bolts 3/4 -10 x 9-inch 2 2 2 2
Pole Cap Top Support Bolt 3/4-10 x 8-inch 1 1 1 1
Pole Cap FlangeNut 3/4-10 3 3 3 3
Set Bolts 1/2 -13 x 1-1/2inch 6 6 6 6
Hex Bolt 1/2-13 x 1-1/2-inch for Adjuster 1 1 1 1
Flange Nut ½ - 13 for Adjuster 1 1 1 1
Adjuster U-Bolt ⅜” x 3-1/8-inch 1 1 1 1
Rectangular Tube 3x2 x 0.12 wall 1 1 2 2
Rectangular Tube 3x2 x 0.188 wall 2 2
Suport Pipe 2-inch Sch 40 1 1 1 1
Suport Pipe 2-inch Sch 80 1 1
Pivot Pipe 2.5-inch Sch 40 1 1
2
1
Pivot Pipe 2.5-inch Sch 80 1 1
Hex Bolt 1/2-13 x 3-1/2-inch 1 1 4 4 4 4
Flat Washer 1/2-inch 1 1 4 4 4 4
U-Bolt w/Nuts for 2-inch Pipe 1 1 8 8 8 8
3.1 Rail 85-inch
4
4
3.1 Rail 66-inch 8 8
Module Rail Splice with Bolts and Nuts 4 4
Module Mounting Clamp 68121216 16
Pipe Mount w/U-Bolt 448 8 8 8
Module Rail End Caps 448 8 8 8
Ground Lug 112 2 2 2
Module Lead Clips 669 9 9 9
Cap Assembly - 4-inchCap Assembly - 6-inchH-FrameModule Mounting Rails
2
4
2

Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Foundaon Hole and Pole Guidelines
• The suggesons below are recommendaons only. It
is the installer’s responsibility to validate foundaon
parameters prior to installaon; a local geotechnical
report may be required to assess soil condions. We
recommend consulng with a local engineer familiar
with local regulaons and build site requirements,
including soil condions, terrain, and load criteria
(wind, snow, seismic). All of these parameters may
impact foundaon requirements.
• If array angle will be seasonally adjusted, use the
foundaon and pole pipe sizing guidelines for the
planned steepest angle. This insures the pole and
foundaon are strong enough to support the array,
as well as maintaining the desired minimum ground
clearance, at all projected angles.
• Highlighted lines in the tables on the next 2 pages
require schedule 80 pipe for the main support pipe.
• Dig hole according to recommended depth and
diameter. Remove or properly compact any loose
material at the boom of the hole.
• The pole length listed in the following tables are
based on having the pole installed 2-3 inches from
the boom of the dug holes. Use a brick, concrete
block, les, or other non-organic solid material at the boom of the hole to support the pole, raising it above the
boom of the hole and allowing concrete to fully encapsulate the pipe pole. If using a thicker material, be sure to
allow for the added thickness when calculang the above-ground and total pole lengths.
• Set pole in hole and use a level to insure that it is straight and plumb in all direcons.
• Brace pole to prevent movement while pouring concrete. Pour so concrete is in direct contact with the soil. If
forming or using sonotube, properly compact backll. Allow concrete to cure for recommended length of me.
Soil Classicaons
• If in doubt about the soil type and holding strength, consult a local engineer.
• Class 3 - Sandy Gravel and/or Gravel - Lateral Bearing Pressure - 200 lbs/sq  below natural grade
• Class 4 - Sand; silty sand, clayey sand, silty gravel, and clayey gravel - Lateral Bearing Pressure - 150 lbs/sq  below
natural grade
• Class 5 - Clay, sandy clay, silty clay, silt and sandy silt - Lateral Bearing Pressure - 100 lbs/sq  below natural grade

6
Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
ArrayTilt
Angle↓
Wind
Speed
(mph)↓
Pipe
Above
Ground
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
100 2.5 6.4 2.1 6.0 2.8 6.7 2.4 6.3 3.3 7.2 2.8 6.7
120 2.9 6.8 2.4 6.3 3.2 7.1 2.7 6.6 3.8 7.7 3.2 7.1
140 3.2 7.1 2.8 6.7 3.6 7.5 3.1 7.0 4.3 8.2 3.6 7.5
100 2.9 7.3 2.5 6.9 3.3 7.7 2.8 7.2 3.8 8.2 3.3 7.7
120 3.4 7.8 2.9 7.3 3.8 8.2 3.2 7.6 4.4 8.8 3.8 8.2
140 3.8 8.2 3.2 7.6 4.3 8.7 3.6 8.0 5.0 9.4 4.3 8.7
100 3.3 8.2 2.8 7.7 3.7 8.6 3.2 8.1 4.3 9.2 3.7 8.6
120 3.8 8.7 3.2 8.1 4.3 9.2 3.6 8.5 5.0 9.9 4.3 9.2
140 4.3 9.2 3.7 8.6 4.8 9.7 4.1 9.0 5.7 10.6 4.8 9.7
100 3.6 8.9 3.1 8.4 4.0 9.3 3.4 8.7 4.7 10.0 4.0 9.3
120 4.1 9.4 3.5 8.8 4.6 9.9 4.0 9.3 5.5 10.8 4.6 9.9
140 4.7 10.0 4.0 9.3 5.2 10.5 4.5 9.8 6.2 11.5 5.2 10.5
100 3.8 9.4 3.3 8.9 4.3 9.9 3.7 9.3 5.0 10.6 4.3 9.9
120 4.4 10.0 3.8 9.4 4.9 10.5 4.2 9.8 5.8 11.4 4.9 10.5
140 5.0 10.6 4.2 9.8 5.6 11.2 4.7 10.3 6.6 12.2 5.6 11.2
ArrayTilt
Angle↓
Wind
Speed
(mph)↓
Pipe
Above
Ground
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
100 2.9 9.8 2.5 9.4 3.3 10.2 2.8 9.7 3.8 10.7 3.3 10.2
120 3.3 10.2 2.9 9.8 3.7 10.6 3.2 10.1 4.4 11.3 3.7 10.6
140 3.8 10.7 3.2 10.1 4.2 11.1 3.6 10.5 4.9 11.8 4.2 11.1
100 3.4 10.8 2.9 10.3 3.8 11.2 3.2 10.6 4.4 11.8 3.8 11.2
120 3.9 11.3 3.3 10.7 4.3 11.7 3.7 11.1 5.1 12.5 4.3 11.7
140 4.4 11.8 3.8 11.2 4.9 12.3 4.2 11.6 5.7 13.1 4.9 12.3
100 3.8 11.7 3.3 11.2 4.2 12.1 3.6 11.5 4.9 12.8 4.2 12.1
120 4.4 12.3 3.7 11.6 4.9 12.8 4.2 12.1 5.7 13.6 4.9 12.8
140 4.9 12.8 4.2 12.1 5.5 13.4 4.7 12.5 6.4 14.3 5.5 13.4
100 4.1 12.3 3.5 11.8 4.6 12.9 3.9 12.2 5.3 13.6 4.6 12.9
120 4.7 13.0 4.0 12.3 5.3 13.6 4.5 12.8 6.1 14.4 5.3 13.6
140 5.3 13.6 4.5 12.8 5.9 14.2 5.1 13.4 6.9 15.2 5.9 14.2
100 4.3 12.9 3.7 12.3 4.8 13.4 4.1 12.7 5.6 14.2 4.8 13.4
120 5.0 13.6 4.3 12.9 5.6 14.2 4.8 13.4 6.5 15.1 5.6 14.2
140 5.6 14.2 4.8 13.4 6.3 14.9 5.4 14.0 7.3 15.9 6.3 14.9
60° 5.9
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 6 Feet at
Lowest Part of the Array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is
4-inch Schedule 40. Highlighted sections in the table below require 4-inch Schedule 80 Pipe.
SoilType→ Class3 Class4 Class5
TTP‐A-2ForArrayGroundClearanceof6Feet
60°
7.1
7.7
8.1
8.6
8.9
50°
24" 36"
20°
30°
40°
FoundationDiameter→ 24" 36" 24" 36"
36"
20°
30°
40°
50° 5.6
5.1
4.7
FoundationDiameter→ 24" 36" 24" 36" 24"
4.1
TTP‐A-2ForArrayGroundClearanceof3Feet
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 3 Feet at
Lowest Part of the Array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is
4-inch Schedule 40. Highlighted sections in the table below require 4-inch Schedule 80 Pipe.
SoilType→ Class3 Class4 Class5

Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Array
Tilt
Angle↓
Wind
Speed
(mph)↓
Pipe
Above
Ground
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
100 3.0 7.5 2.5 7.0 3.3 7.8 2.8 7.3 3.9 8.4 3.3 7.8
120 3.5 7.9 2.9 7.4 3.8 8.3 3.3 7.8 4.5 9.0 3.8 8.3
140 4.0 8.4 3.3 7.8 4.3 8.8 3.7 8.2 5.1 9.6 4.3 8.8
100 3.6 8.9 3.1 8.4 4.0 9.3 3.4 8.7 4.7 10.0 4.0 9.3
120 4.2 9.5 3.6 8.9 4.6 9.9 3.9 9.2 5.4 10.7 4.6 9.9
140 4.7 10.0 4.0 9.3 5.2 10.5 4.4 9.7 6.1 11.4 5.2 10.5
100 4.1 10.1 3.5 9.5 4.5 10.5 3.9 9.9 5.3 11.3 4.5 10.5
120 4.7 10.7 4.0 10.0 5.3 11.2 4.5 10.5 6.2 12.2 5.2 11.2
140 5.3 11.3 4.5 10.5 5.9 11.9 5.0 11.0 7.0 13.0 5.9 11.9
100 4.4 11.0 3.8 10.4 4.9 11.5 4.2 10.8 5.8 12.4 4.9 11.5
120 5.1 11.7 4.4 11.0 5.7 12.3 4.8 11.4 6.6 13.3 5.6 12.1
140 5.7 12.3 4.9 11.5 6.4 13.0 5.4 12.0 7.5 14.1 6.2 13.0
100 4.7 11.8 4.0 11.1 5.2 12.3 4.5 11.6 6.1 13.2 5.2 12.3
120 5.4 12.4 4.6 11.7 6.0 13.1 5.2 12.3 7.1 14.3 6.0 13.1
140 6.1 13.0 5.2 12.3 6.8 13.9 5.8 12.9 8.0 15.1 6.8 13.9
Array
Tilt
Angle↓
Wind
Speed
(mph)↓
Pipe
Above
Ground
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
Hole
Depth
(ft)
Total
Pipe
Length
(ft)
100 3.4 10.9 3.0 10.5 3.8 11.3 3.3 10.8 4.5 12.0 3.8 11.3
120 3.9 11.4 3.4 10.9 4.4 11.9 3.8 11.3 5.2 12.7 4.4 11.9
140 4.4 11.9 3.8 11.3 5.0 12.5 4.3 11.8 5.8 13.3 5.0 12.5
100 4.1 12.4 3.5 11.8 4.5 12.8 3.9 12.2 5.3 13.6 4.5 12.8
120 4.7 13.0 4.0 12.3 5.2 13.5 4.5 12.8 6.1 14.4 5.2 13.5
140 5.3 13.6 4.5 12.8 5.9 14.2 5.0 13.3 6.9 15.2 5.9 14.2
100 4.5 13.5 3.8 12.8 5.0 14.0 4.3 13.3 5.8 14.8 5.0 14.0
120 5.2 14.2 4.4 13.4 5.8 14.8 4.9 13.9 6.7 15.7 5.8 14.8
140 5.8 14.8 5.0 14.0 6.5 15.5 5.5 14.5 7.6 16.6 6.5 15.5
100 4.9 14.5 4.2 13.8 5.5 15.1 4.7 14.3 6.4 16.0 5.5 15.1
120 5.7 15.3 4.8 14.4 6.3 15.9 5.4 15.0 7.4 17.0 6.3 15.9
140 6.4 16.0 5.4 15.0 7.1 16.7 6.1 15.7 8.3 17.9 7.1 16.7
100 5.2 15.3 4.5 14.6 5.8 15.9 5.0 15.1 6.8 16.9 5.8 15.9
120 6.0 16.1 5.2 15.3 6.7 16.8 5.7 15.8 7.8 17.9 6.7 16.8
140 6.7 16.8 5.8 15.9 7.5 17.6 6.4 16.5 8.8 18.9 7.5 17.6
7.7
8.5
9.2
9.8
10.3
36"
SoilType→ Class3 Class4 Class5
FoundationDiameter→ 24" 36" 24" 36" 24"
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 4 Feet at Lowest
Part of the Array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is 4-inch
Schedule 40. Highlighted sections in the table below require 4-inch Schedule 80 Pipe.
30°
20° 4.7
5.5
60°
50°
40°
30°
20°
24" 36"
60°
50°
40°
FoundationDiameter→ 24" 36" 24" 36"
6.2
6.8
7.3
TTP‐A-3ForArrayGroundClearanceof6Feet
SoilType→ Class3 Class4 Class5
TTP‐A-3ForArrayGroundClearanceof3Feet
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 3 Feet at Lowest
Part of the Array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is 4-inch
Schedule 40. Highlighted sections in the table below require 4-inch Schedule 80 Pipe.

8
Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Array
Tilt
Angle
↓
Wind
Speed
(mph)↓
PipeAbove
Ground(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
100 3.3 7.2 2.8 6.7 3.6 7.5 3.1 7.0 4.3 8.2 3.6 7.5
120 3.8 7.7 3.2 7.1 4.2 8.1 3.6 7.5 5.0 8.9 4.2 8.1
140 4.3 8.2 3.6 7.5 4.8 8.7 4.1 8.0 5.6 9.5 4.8 8.7
100 3.8 8.2 3.2 7.6 4.2 8.6 3.6 8.0 5.0 9.4 4.2 8.6
120 4.4 8.8 3.7 8.1 4.9 9.3 4.2 8.6 5.8 10.2 4.9 9.3
140 5.0 9.4 4.2 8.6 5.6 10.0 4.7 9.1 6.6 11.0 5.6 10.0
100 4.3 9.2 3.6 8.5 4.8 9.7 4.1 9.0 5.6 10.5 4.8 9.7
120 4.9 9.8 4.2 9.1 5.5 10.4 4.7 9.6 6.5 11.4 5.5 10.4
140 5.6 10.5 4.8 9.7 6.3 11.2 5.3 10.2 7.4 12.3 6.3 11.2
100 4.7 10.0 4.0 9.3 5.2 10.5 4.4 9.7 6.1 11.4 5.2 10.5
120 5.4 10.7 4.6 9.9 6.0 11.3 5.1 10.4 7.1 12.4 6.0 11.3
140 6.1 11.4 5.2 10.5 6.9 12.2 5.8 11.1 8.1 13.4 6.9 12.2
100 5.0 10.6 4.2 9.8 5.6 11.2 4.7 10.3 6.5 12.1 5.6 11.2
120 5.7 11.3 4.9 10.5 6.4 12.0 5.5 11.1 7.6 13.2 6.4 12.0
140 6.5 12.1 5.5 11.1 7.3 12.9 6.2 11.8 8.6 14.2 7.3 12.9
Array
Tilt
Angle
↓
Wind
Speed
(mph)↓
PipeAbove
Ground(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
100 3.80 10.68 3.30 10.18 4.20 11.08 3.60 10.48 4.90 11.78 4.20 11.08
120 4.40 11.28 3.70 10.58 4.90 11.78 4.20 11.08 5.70 12.58 4.90 11.78
140 4.90 11.78 4.30 11.08 5.50 12.38 4.70 11.58 6.40 13.28 5.50 12.38
100 4.40 11.80 3.70 11.10 4.90 12.30 4.20 11.60 5.70 13.10 4.90 12.30
120 5.00 12.40 4.30 11.70 5.60 13.00 5.80 12.20 6.60 14.00 5.60 13.00
140 5.70 13.10 4.80 12.20 6.30 13.70 5.40 12.80 7.40 14.80 6.30 13.70
100 4.90 12.77 4.20 12.07 5.40 13.27 4.70 12.57 6.40 14.27 5.40 13.27
120 5.60 13.47 4.80 12.67 6.30 14.17 5.40 13.27 7.40 15.27 6.30 14.17
140 6.30 14.17 5.40 13.27 7.10 14.97 6.00 13.87 8.30 16.17 7.10 14.97
100 5.30 13.58 4.50 12.78 5.90 14.18 5.00 13.28 6.90 15.18 5.90 14.18
120 6.10 14.38 5.20 13.48 6.80 15.08 5.80 14.08 8.00 16.28 6.80 15.08
140 6.80 15.08 5.80 14.08 7.70 15.98 6.50 14.78 9.00 17.28 7.70 15.98
100 5.60 14.21 4.80 13.41 6.20 14.81 5.30 13.91 7.30 15.91 6.20 14.81
120 6.40 15.01 5.50 14.11 7.20 15.81 6.10 14.71 8.40 17.01 7.20 15.81
140 7.20 15.81 6.20 14.81 8.10 16.71 6.90 15.51 9.50 18.11 8.10 16.71
TTP‐A-4andTTP‐A-4HWforArrayGroundClearanceof3Feet
4.7
5.1
20°
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 3 Feet at Lowest Part of
the Array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is 6-inch Schedule 40
(Highlighted sections require 6-inch Schedule 80 Pipe)
SoilType→ Class3 Class4 Class5
FoundationDiameter→ 36"
4.1
24" 36" 24" 36"
60°
30°
40°
50°
60°
20°
30°
40°
50°
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 6 Feet at Lowest Part of
the Array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is 6-inch Schedule 40
(Highlighted sections require 6-inch Schedule 80 Pipe)
SoilType→
FoundationDiameter→
5.5
5.9
36" 24"
7.13
7.65
8.12
8.53
8.86
24"
36" 24" 36"
Class3 Class5Class4
24"
TTP‐A-4andTTP‐A-4HWforArrayGroundClearanceof6Feet

Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Array
Tilt
Angle↓
Wind
Speed
(mph)↓
PipeAbove
Ground(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
100 3.9 8.4 3.3 7.8 4.3 8.8 3.7 8.2 5.1 9.6 4.3 8.8
120 4.5 9.0 3.8 8.3 5.0 9.5 4.2 8.7 5.9 10.4 5.0 9.5
140 5.0 9.5 4.3 8.8 5.7 10.2 4.8 9.3 6.7 11.2 5.7 10.2
100 4.6 9.9 4.0 9.3 5.2 10.5 4.4 9.7 6.1 11.4 5.2 10.5
120 5.4 10.7 4.6 9.9 6.0 11.3 5.1 10.4 7.1 12.4 6.0 11.3
140 6.1 11.4 5.2 10.5 6.8 12.1 5.8 11.1 8.1 13.4 6.8 12.1
100 5.3 11.3 4.5 10.5 5.9 11.9 5.0 11.0 6.9 12.9 5.9 11.9
120 6.2 12.1 5.2 11.2 6.8 12.8 5.8 11.8 8.0 14.0 6.8 12.8
140 6.9 12.9 5.8 11.8 7.7 13.7 6.6 12.6 9.1 15.1 7.7 13.7
100 5.7 12.3 4.8 11.4 6.4 13.0 5.4 12.0 7.5 14.1 6.4 13.0
120 6.6 13.2 5.6 12.2 7.4 14.0 6.3 12.9 8.7 15.3 7.4 14.0
140 7.4 14.0 6.3 12.9 8.3 14.9 7.1 13.7 9.9 16.5 8.3 14.9
100 6.1 13.2 5.2 12.3 6.8 13.9 5.8 12.9 8.0 15.1 6.8 13.9
120 7.0 14.1 6.0 13.1 7.8 14.9 6.7 13.8 9.2 16.3 7.8 14.9
140 7.9 15.0 6.7 13.8 8.9 16.0 7.5 14.6 10.5 17.6 8.9 16.0
Array
Tilt
Angle↓
Wind
Speed
(mph)↓
PipeAbove
Ground(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
Hole
Depth
(ft)
TotalPipe
Length(ft)
100 4.4 11.9 3.8 11.3 4.9 12.4 4.2 11.7 5.8 13.3 4.9 12.4
120 5.1 12.6 4.4 11.9 5.7 13.2 4.9 12.4 6.7 14.2 5.7 13.2
140 5.7 13.2 4.9 12.4 6.4 13.9 5.5 13.0 7.5 15.0 6.4 13.9
100 5.3 13.6 4.5 12.8 5.9 14.2 5.0 13.3 6.9 15.2 5.9 14.2
120 6.0 14.3 5.2 13.5 6.8 15.1 5.8 14.1 7.9 16.2 6.8 15.1
140 6.8 15.1 5.8 14.1 7.6 15.9 6.5 14.8 9.0 17.3 7.6 15.9
100 5.8 14.8 4.9 13.9 6.4 15.4 5.5 14.5 7.5 16.5 6.4 15.4
120 6.6 15.6 5.7 14.7 7.4 16.4 6.3 15.3 8.7 17.7 7.4 16.4
140 7.5 16.5 6.4 15.4 8.4 17.4 7.1 16.1 9.8 18.8 8.4 17.4
100 6.3 15.9 5.4 15.0 7.1 16.7 6.1 15.7 8.3 17.9 7.1 16.7
120 7.3 16.9 6.2 15.8 8.2 17.8 7.0 16.6 9.6 19.2 8.2 17.8
140 8.2 17.8 7.0 16.6 9.2 18.8 7.8 17.4 10.8 20.4 9.2 18.8
100 6.7 16.8 5.8 15.9 7.5 17.6 6.4 16.5 8.8 18.9 7.5 17.6
120 7.7 17.8 6.6 16.7 8.7 18.8 7.4 17.5 10.2 20.3 8.7 18.8
140 8.7 18.8 7.4 17.5 9.8 19.9 8.3 18.4 11.5 21.6 9.8 19.9
TTP‐A-6andTTP‐A-6HWforArrayGroundClearanceof3Feet
SoilType→
4.71
60°
20°
30°
40°
50°
20°
30°
40°
50°
60°
24" 36"
Class3 Class4 Class5
8.5
9.21
36" 24" 36"
24" 36"
Class3 Class4 Class5
FoundationDiameter→
TTP‐A-6andTTP‐A-6HWforArrayGroundClearanceof6Feet
9.83
10.33
24"
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 3 Feet at lowest part of the
array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameter. Vertical Pipe is 6-inch Schedule 40 (Highlighted
sections require 6-inch Schedule 80 Pipe)
Foundation Hole Depth, Height of Pole Above Ground and Total Pole Length for Ground Clearance of 6 Feet at lowest part of the
array & Exposure Catgory B For Various Soil Class and Foundation Hole Diameters. Vertical Pipe is 6-inch Schedule 40 (Highlighted
sections require 6-inch Schedule 80 Pipe)
SoilType→
FoundationDiameter→
7.71
36" 24" 36"
5.50
6.21
6.83
7.33
24"

10
Installaon Manual Pole Mount
TTP-A Series
[e-mail] 1-800-819-7236 Ext 556 PAGE
Step One - Pole Cap Assembly
• Place Pole Cover on top of mounng pole.
• Put 3/4 x 8-inch Cap Support Bolt through the two top holes in rear half of the Pole Cap,
install nut and ghten rmly. It is not necessary to torque this bolt and nut. This bolt keeps
the Pole Cap from sliding down the post.
• Put the two 3/4 x 9-inch bolts into back half of Pole Cap, then through front
(larger) half, and put nut loosely on the bolt. These large nuts and bolts may
be dicult to thread together by hand. Start nuts on bolts by hand and use
wrenches as needed. Booms of cap will hook together.
• Slide assembled Pole Cap over 6-inch vercal pole. Front and back of cap
assembly should be aligned so the two 9-inch bolts are approximately
horizontal and top edge of the front (larger) part of cap is against the vercal
pole. Rotate Pole Cap on post so front (larger) half of Pole Cap is on side of
pole that array will be facing.
• Loosely install the four 1/2-inch set screws in threaded holes on rear half of
Pole Cap. Do not ghten at this me.
• Securely ghten the two 3/4” bolts in Pole Cap assembly, keeping them
horizontal. Tighten enough that front of cap will not slide down the pipe.
Do not fully torque to specicaon unl nal assembly is complete.
Step Two - Assemble H-Frame
• Slide 2-1/2-inch Pivot Pipe (2-7/8” O.D.) through holes on side of front half of
Top Cap and center in front half of Top Cap.
• Bolt a 2 x 3-inch Tube to each side of Pivot Pipe with a 1/2 x 3-inch bolt, at
washer and split lock washer. Use hole in the center of the 2” x 3” Tube.
• Bolt 2-inch Adjuster Pipe (2-3/8-inch O.D.) between the two 2 x 3-inch Tubes
with a 1/2 x 3-inch bolt, at washer, and split lock washer on each side.
Assembly should look like picture below. Tighten the 4 bolts to 45 -lbs.