T&S B-2730 Series User manual

Installationand
Maintenance
Instructions
B-2730&B-2731
SERIES
SINGLELEVER FAUCETS
(with or without Sidespray)
Español: la Instalación y las
Instruccionesde
Mantenimiento
Limited One Year Warranty
T&Swarrantstotheoriginalpurchaser(otherthan
forpurposesofresale)thatsuchproductisfreefrom
defectsinmaterialandworkmanshipforaperiodof
one(1)yearfromthedateofpurchase. Duringthis
one-yearwarrantyperiod, iftheproductis foundto
bedefective,T&S shall,at itsoptions, repairand/
orreplaceit. Toobtainwarrantyservice,products
mustbereturnedto...
T&SBrassandBronzeWorks,Inc.
Attn: WarrantyRepairDepartment
2SaddlebackCove
TravelersRest,SC 29690
Shipping,freight,insurance,andothertranspor-
tationchargesoftheproducttoT&Sandthereturn
ofrepairedorreplacedproducttothepurchaserare
theresponsibilityofthepurchaser. Repairand/or
replacementshallbemadewithinareasonabletime
afterreceiptbyT&Softhereturned product. This
warrantydoesnotcoverItemswhichhavereceived
secondaryfinishingorhavebeenalteredormodi-
fiedafterpurchase, orfordefectscausedbyphysi-
calabuseto ormisuseoftheproduct,orshipment
oftheproducts.
Anyexpresswarrantynotprovidedherein,and
anyremedyforBreachofContractwhichmightarise,
is hereby excluded and disclaimed. Any implied
warrantiesofmerchantabilityorfitnessforaparticu-
larpurposearelimitedtooneyearinduration. Under
no circumstances shall T&S be liable for loss of
useor anyspecialconsequentialcosts,expenses
ordamages.
Somestatesdonotallowlimitationsonhowlong
andimpliedwarrantylastsortheexclusionorlimi-
tationof incidentalorconsequentialdamages,so
theabovelimitationsorexclusionsmay not apply
toyou. Specificrightsunderthiswarrantyandother
rightsvaryfromstatetostate.
P/N: 098-013123-45 Rev.3
Date: 03-01-04
Drawn: TEH
Checked:
Approved: MVW04-30-04 MVW04-30-04

Exploded View
*Some items are listed for instructional purposes
and may not be sold as separate parts.
2

Part Number Guide
3
Single Lever Lavatory Faucet Assembly
Asm, Single Lever Faucet w/ Sidespray B-2730
Asm, Single Lever Faucet B-2731
1Body, Faucet *
Center Mounting Kit 014163-45
2Spacer, Foam *
3Washer, Lock *
4Post, Center Mounting *
5Locknut, Center Mounting Post *
6Deckplate *
7Gasket, Mounting
Plastic 014160-45
Zinc 014161-45
Kit, Side Mounting Post & Locknut 014162-45
8Post *
9Locknut *
10 Sidespray
4ft. Hose 013842-45
7ft. Hose (B-2730-07) 012975-45
11 Retaining Ring *
12 Retaining Nut *
13 Cartridge, Metal Stem w/ Temp. Limit Stop 013080-45
14 Handle
Standard 013113-45
Long 013429-45
15 Plug 014173-45
16 * Hex Key, 3/32" 010587-45
17 Post, Sidespray Connection *
18 Flexible Stainless Steel Supplies *
19 Hose Guide 001496-45
20 Locknut, Hose Guide *
* Hex Key not provided

General Instructions
Faucet Installation
1. Shut off water supply and drain lines. Clean sink surface thoroughly.
2. Place no.6with no.7on deck in line with mounting holes.
3. Hand tighten no.18 into no.1.Carefully slide no.18 through center sink hole.
4. Insert no.8under deck and thread tightly into no.6. Thread no.9onto no.8and
tighten fully against underside of countertop.
5. Insert no.4into no.1tightly. Slide no.2and no.3onto no.4. Thread no.5onto
no.4. Tighten fully against underside of countertop.
6. Place no.19 into hole in countertop. Thread no.20 onto no.19 and tighten fully
against underside of countertop.
7. Slide no.10 through no.19. Connect no.10 to outlet no.17.
8. Connect water supply lines and check for leaks.
Maintenance:
1. To change no.13, remove no.15 by hand.
2. Insert no.16 into hole of no.14 and loosen set screw of no.14. Remove no.14.
3. Unscrew no.11 by hand and remove.
4. Unscrew no.12 by hand and remove.
5. Remove no.13 and replace with new no.13.
6. Replace no.12, no.11 and no.14 and tighten set screw.
7. Replace no.15.
4
4
7
61
220
5
19
3
8
18
17
10
14
11
9sink

5
General Instructions
1. Remove no.15, then using
no.16, loosen set screw and
lift off no.14
2. Unscrew no.11.
3. Unscrew no.12.
4. Adjust no.13 to desired
position per below.
Normal factory
set position
allowsfull
mixing of hot
andcold water.
Using needle
nose pliers,
carefullylift off
thetemperature
limitstopring
from the cartridge
body. Re-set the
ring onto the
body per Figure 4
or5.
Place ring into
this position to
reduce the
amount of hot
wateravailable.
Result: cold to
warmwateronly.
Place ring into
this position to
reduce the
amount of cold
wateravailable.
Result: warm to
hot water only.
Figure 1
Figure 2 Figure 3
Figure 5
Figure 4

6
Instrucciones
Generales
Mantenimiento:
1. Para cambiar la parte No.13, remueva a mano la parte No.15.
2. Ensarte la parte No.16 en el hueco de la parte No.14 y afloje el tornillo presión
de la parte No.14. Remueva la parte No.14.
3. Destornille la parte No.11 y remuévala.
4. Destornillela parte No.12 y remuévala.
5. Remueva la parte No.13 y reemplace con una parte nueva No.13.
6. Reemplacela parteNo.12, No.11 y laparte No.14.Aprieteel tornillodepresión.
7.Reemplace laparte No.15.
4
7
61
220
5
19
3
818
17
10
14
11
9Lavatorio
Instalación de la canilla:
1.Cierre la fuente principal de agua y desagüe las tuberías. Limpie muy bien la
superficie del lavatorio.
2. Coloque la parte No.6con la parte No.7sobre la cubierta en línea con los
huecos de montadura.
3.Apriete a manola parte No.18a la parte No.1Cuidadosamentedeslice la parte
No.18 a través del hueco del centro del lavatorio.
4. Ensarte la parte No.8a la parte No.6 por debajo de la cubierta y apriete
aseguradamente. Enrosque la parte No.9en la parte No.8 y apriete por completo
contra la parte de abajo del mostrador.
5. Ensarte la parte No.4 dentro de la parte No.1apretadamente. Deslice las parte
No.2y No.3en la parte No.4. Enrosque la parte No.5en la parte No.4.Aprietepor
completo contra la parte de abajo del mostrador.
6. Coloque la parte No.19 en el hueco del mostrador. Enrosque la parte No.20en la
parte No.19 y apriete por completo contra la parte de abajo del mostrador.
7. Deslice la parte No.10 a través de la parte No.19. Conecte la parte No.10 ala
línea de salida No.17.
8. Conecte las líneas de surtido e inspeccione por filtraciones.

7
Instrucciones
Generales
1. Remueva la parte No.15, luego
afloje el tornillo de presión
utilizando la parte No.8,y
remueva la parte No.14 alzándola.
2. Destornille la parte No.11.
3. Destornillela parteNo.12.
4. Ajuste la parte No.13ala
posición deseada como lo indica
abajo.
La posición
ajustada en la
factoría permite
lamayor mezcla
de agua fría y
caliente.
Cuidadosamente
levante la argolla de
limitación de
temperatura del
cuerpo del cartucho
utilizando alicates
de punta. Coloque
de nuevo la argolla
dentro del cuerpo
como indicado en el
dibujo 4 o 5.
Coloquela
argolla en esta
posición para
reducir la
cantidad de
aguacaliente
disponible.
Resultado:
Solamenteagua
tibiaa fría.
Coloquela argolla
en esta posición
parareducir la
cantidad de agua
fríadisponible.
Resultado:
Solamenteagua
tibia a caliente.
Dibujo 2 Dibujo 3
Dibujo 5Dibujo 4
Dibujo 1

T&S BRASS AND BRONZE WORKS, INC.
A firm commitment to application-engineered plumbing products
2 Saddleback Cove, P.O. Box 1088, T & S Brass-Europe
Travelers Rest, SC 29690 ‘De Veenhoeve’
Phone: [phone] Oude Nieuwveenseweg 84
Fax: [phone] CW Nieuwveen
E-mail: [email protected] The Netherlands
B-2710 & B-2711
Single Lever
Faucets