Tannoy Arenaccessories User manual

Centre Channel Stand / Wall Bracket Accessory Manual

3
4mm Allen key for stand to centre fixing screws
3mm Allen key for ball joint screws Table stand
x 1
x 1 x 1
stand to centre fixing screws x 2
shake proof washer for stand fixing screws x 2

Step one: Satellite fixing bracket
Step two: Cable management – table
stand application
Ensure that the audio system amplifier is switched
off and then feed the speaker cable up through the
base and ball joint of the stand. Prepare the speaker
cable by stripping 6mm (1/4inch) of insulation and
connect to the relevant terminal on the base of the
centre speaker unit.
The positive conductor (marked with line, text print
or raised rib) connects to the terminal with the red
insert ring while the negative cable goes to the
terminal marked with the black insert. 4
Cable management routing through ball joint

5
Step three: Centre channel fitting to stand
Locate the unit into the cradle of the table / wall stand, ensuring
that the speaker cable is carefully routed to avoid damage.
Using the 4mm Allen key, insert the two chrome screws and
lock washers into the underside of the unit and tighten to fully
secure the unit.

6
Step four: Grille fitting
If intending to use the grille you must remove the
coloured trim piece using the finger recess behind the
trim and locate the bottom section of the grille into
the recess on the stand. Use the 4mm Allen driver to
insert chrome screw to secure the grille in place.
The grille is designed to stand off from the front baffle
of the satellite so do not over tighten the screw.

7
Step five: Adjustment and locking of
the ball joint – table stand
The ball joint mechanism allows great flexibility in the
positioning of the centre speaker in relation to the
stand. Simply move the speaker to desired position, set
in the required orientation and then use the 3mm Allen
driver to tighten the four chrome screws to secure the
satellite in the desired position.
Tighten all four evenly at quarter turn increments to
lock the ball joint - do not over tighten the screws.

8
Step six: Wall bracket application
– orientation of bracket
The universal design of the stand allows for
wall mount use. Use the 3mm Allen key to
slacken the four screws on the ball joint plate
(fig. 1) slightly – rotate the assembly through
1800and retighten (fig. 2).
Tighten all four screws evenly at quarter turn
increments to lock the ball joint - do not over
tighten the screws.
Route the signal cable from the base of the
stand through the cable management in the
centre of the ball joint
2
1

9
Step seven: Wall bracket application – wall plate
Use the 4mm Allen key to remove the chrome screw retaining the wall
mounting plate (figs.1 and 2). Remove the plate from the base (fig. 3)
and mark the positions of the mounting screws on the wall surface.
WARNING:
Ensure that you utilise the correct wall fixings (screws, Rawlplug, Rawlbolt, toggle fixing, expanding insert etc) designed to provide maximum security of fastening to your
wall construction. If in doubt you must consult a professional – incorrect fixing methods can be dangerous.
1 2 3
4 5 6 7
37 7 7
WARNING: Product Orientation
When wall mounting the Centre or Satellite product you must ensure that
it is installed ONLY as it appears in Fig 1 above. The lock washer must also be used,
as it is an integral part of the securing mechanism.
Fig 4: CORRECT
Fig 5: INCORRECT – lock washer missing
Fig 6: INCORRECT ORIENTATION
Fig 7: INCORRECT ORIENTATION

10
Step eight: Wall bracket application – fixing to wall and adjustment
Carefully dress the signal cable through the cable management and offer the bracket base to the
secured wall mount plate. Using the 4mm Allen key, insert the chrome screw through the bracket and
tighten to secure the assembly to the wall plate.
Simply move the speaker to set the set the required orientation and then use the 3mm Allen driver to
tighten the four chrome screws to secure the satellite in the desired position.
Tighten all four screws evenly at quarter turn increments to lock the ball joint - do not over tighten the
screws.