TCL LIFE CAM User manual

Quick Start Guide
CJB1HC004AAA

2
What's In The Box?
LIFECAM x 1 Charger x 1 Screw x 2
Quick start guide
USB cable x 1 (1.8 meter) Quick start guide x 1 Wall plug x 2
Metal mounng bracket

3
Specicaon
Product name LIFECAM
Model name IC01
Operang frequency 2.4 GHz
Transmied power 17±2dbm (Mode: 11b, Rate: 1Mbps)

4
Geng to Know Your LIFECAM
The LIFECAM is a Wi-Fi IP camera which provides remote viewing
and broadcasng features when used in combinaon with the LIFE
App.
MIC
Light sensor
Lens
LED indictor
Speaker
USB port
Reset hole
SD card slot
Metal mounng
bracket
Note:
You can adjust your LIFECAM angle by manually rotang the camera head.

5
Your LIFECAM: Quick Setup Guide
1. Download the LIFE Applicaon
Download the App using either of the QR codes shown below. Both
QR codes are also printed on the box. Alternavely, you can also
search for “LIFE” in the Apple Store or in Google Play Store.
Apple Store Google Play
2. Installing a Micro-SD Card
Insert the Micro-SD card
according to the illustraon.
Note: In order to enable video
recording, you will rst need
to insert a Micro-SD card. The
system will automacally save the
video in the SD card when the
alarm is triggered.
SD Card format:
Speed: Class 4 or above
Capacity: 8-32GB
Type: TF Card (Micro-SD
Card)
Format: FAT32

6 7
3. Connecng Your LIFECAM
1) Ensure that your LIFECAM is located in your Wi-Fi signal coverage
zone. For opmal performance, the Wi-Fi uploading bandwidth
should be at least 0.6 Mbps.
2) Ensure that your smartphone and your LIFECAM are in the same
Wi-Fi signal coverage zone.
Note: This device does not support 5GHz Wi-Fi. Please connect to a 2.4GHz
Wi-Fi router.
3) Connect your LIFECAM to the power supply as shown in the
following gure.
Note: When the LIFECAM is connected to the power supply, the LED
indicator light will turn red, and it will take about 20 seconds to boot up.
4) Open the LIFE App, create an account and log in.

7
5) When you hear "Ready to congure LIFECAM" from the audio
prompt and the LED ashes red, select “+” in the LIFE App, and
follow the on-screen instrucons to add and congure your
LIFECAM. Once your LIFECAM connects to the Wi-Fi network
successfully, the LED will turn o.
Note: Please reset your LIFECAM If the LED connues to ash, or you hear
"Sorry, adding LIFECAM failed, please try again" from the audio prompt.
Reseng Your LIFECAM
If you want to change the LIFECAM Wi-Fi sengs, or your LIFECAM
connecon fails, please long press the reset buon using the reset
pin for 5 seconds. An audio guide will nofy you if the reset has
succeeded.
Note: Please add your LIFECAM again in the App aer you reset it.

8 9
Installing Your LIFECAM
You can place your LIFECAM on a desk or install it on a wall.
Note:
• Please place your LIFECAM in an area with an unobstructed
view.
• Please do not place your LIFECAM behind furniture or near a
microwave oven.
• Please do not place your LIFECAM in areas prone to high
humidity or where condensaon might form.
Desktop Installaon
Place your LIFECAM on a desk in an area which is clean and dry, with
an unobstructed view, and which is beyond the reach of children.

9
Wall Installaon
1. Find a suitable place to install your LIFECAM.
2. Separate the metal mounng bracket from the base of your
LIFECAM.
3. Use the metal mounng bracket with its two holes as a template
to mark the mounng posion of your LIFECAM on your wall (the
distance between the two holes is 28 mm). Drill two holes into
the wall.
4. Insert the wall plugs into the holes.
5. Fix the metal mounng bracket onto the wall using the screws.
6. Reaach your LIFECAM to the metal mounng bracket which is
now xed to the wall.
LIFECAM
Note:
• Don't install your LIFECAM
outdoors.
• Avoid direct or strong sunlight.
• Avoid installing your LIFECAM
near water vapour or in areas of
high humidity.
• Please don't install your
LIFECAM in an unstable or
vibraon prone area.
• Please don’t place your
LIFECAM vercal to frequently
moving objects, such as cur-
tains and windows.
Holes in
the wall
Wall plug Metal mounng
bracket
Screw

10
FAQ
1. Q: Which OS version is compable with the App?
A: iOS 7.0 and above versions, Android 4.0 and above versions.
2. Q: What should I do if I am unable to add my LIFECAM?
A: 1) Use the reset pin to reset your LIFECAM. Wait unl you
hear the audio guide and then try to add it again.
2) Please check that you have entered the correct Wi-Fi SSDI
and password, then try again.
3) Please check if your router is appearing in your Wi-Fi black
list or the opon to prevent loitering on your network has been
enabled.
4) Please check if your Wi-Fi router has been set to the 5 GHz
frequency band. Currently, LIFECAM does not support the 5
GHz Wi-Fi frequency, so please set the Wi-Fi router to the 2.4
GHz band.
5) Please check if your smartphone permission sengs are
prevenng the LIFE App from using Wi-Fi and GPS.
6) Please check if your Wi-Fi router has been set to bridge mode.
Bridge mode can cause the Wi-Fi signal to become unstable so

11
we do not recommend that you connect your LIFECAM to your
Wi-Fi this way.
3. Q: What should I do when my LIFECAM is oine?
A: 1) Please check your LIFECAM's power supply and Wi-Fi
connecon.
2) Reconnect and reset your LIFECAM, and add it again in the
App.
4. Q: Does my LIFECAM only work with the LIFE App within the
same WLAN?
A: No. If your LIFECAM and LIFE app can connect to the
internet, there are no limits to the distance which can be
between them.
5. Q: Can my LIFECAM work from a baery?
A: No, the LIFECAM does not contain a baery, it supports a
1A/5V or 2A/5V charger power supply.
6. Q: Are the materials used in the product harmful to pets or
children?
A: All materials have passed the related safety tesng for
children so as to ensure their safety.

12
7. Q: Is it normal to hear a “snip-snap” sound inside the camera
when it switches to night mode?
A: Yes, it’s normal. LIFECAM will switch its internal IR-CUT lter
on or o when it changes between day and night modes.
8. Q: Is it normal for the housing of my LIFECAM to feel warm?
A: Yes. It’s normal when the LIFECAM switches to night mode.
9. Q: Can the camera sll record, even when it is oine?
A: The camera can sll record to the local SD card, even when
it is oine. However, when you want to view the recorded le,
your camera and smartphone will need to be connected via the
internet.
10. Q: How many days of recording can be stored on my SD
Card?
A: 8GB: 4days 16GB: 8days 32GB: 16days
11. Q: If the SD Card storage is full, will it stop recording?
A: No. It will connue by overwring the oldest le on the card.

13
12. Q: What do I do if my SD card can’t be read?
A: 1) Please check that you have inserted the SD card correctly.
2) Please make sure the SD card format is FAT32 or EXFAT.
3) Somemes, restarng the camera will solve this issue.
4) Please try to reinsert the SD card.
13. Q: How many accounts can my LIFECAM be linked with?
A: In order to protect the user's account security, only one
LIFECAM can be linked with one account. That account holder
will then be the administrator. Other users can be invited only
by the administrator. They will have the same rights as the
administrator except they will not be able to manage other
users.
14. Q: How can I be sure my LIFECAM is securely protected?
A: 1) Your LIFECAM, app and cloud are secured with two-way
authencaon interacons to protect user idencaon.
2) Video streaming uses a private encrypon protocol for
transfer.
3) User idencaon and video stream idencaon are kept
separate so that security is twice as strong.

14
Safety and Use
Electronic Devices
Turn o your device near high-precision electronic devices. The
wireless device may aect the performance of these devices.
Such devices include hearing aids, pacemakers, re alarm systems,
automac gates, and other automac devices. If you are using an
electronic medical device, consult the device manufacturer to
conrm whether radio waves aect its operaon.
Hospitals
Pay aenon to the following points in hospitals or health care
facilies:
• Do not take your wireless device into the operang room, inten-
sive care unit, or coronary care unit.
• Do not use your wireless device at places for medical treatment
where wireless device use is prohibited.
Storage Environment
• Do not place magnec storage media such as magnec cards and
oppy disks near the wireless device. Radiaon from the wireless
device may erase the informaon stored on them.
• Do not put your wireless device and other accessories in contain-

15
ers with strong magnec elds, such as an inducon cooker or a
microwave oven. Otherwise, circuit failure, re, or explosion may
occur.
• Do not leave your wireless device in a very hot or cold place.
Otherwise, malfuncon of the product, re, or explosion may oc-
cur.
• Do not subject your wireless device to serious collision or shock.
Otherwise, wireless device malfuncon, overheang, re, or ex-
plosion may occur.
Child Safety
• Put your wireless device in places beyond the reach of children.
Do not allow children to use the wireless device without guid-
ance.
• Do not allow children to put the device in their mouths.
• Do not allow children to touch small ngs. Otherwise, suoca-
on or choking could occur if they are swallowed.
Operang Environment
• The wireless device is not water-resistant. Keep it dry. Protect
the wireless device from water or vapour. Do not touch the wire-
less device with a wet hand. Otherwise, short-circuit, malfunc-
on of the product or electric shock may occur.

16
• Do not use the wireless device in dusty, damp and dirty places
or within magnec elds. Otherwise, malfuncon of the circuitry
may occur.
• The wireless device may interfere with nearby TV sets, radios and
PCs.
• In accordance with internaonal standards for radio frequency
and radiaon, use wireless device accessories approved by the
manufacturer only.
Trac Safety
When driving, do not use the wireless device.
• When switched on, this device emits electromagnec waves that
can interfere with the vehicle’s electronic systems such as ABS
an-lock brakes or airbags. To ensure that there is no problem,
do not place this device on top of the dashboard or within an
airbag deployment area.
• Check with your car dealer or the car manufacturer to make sure
that the dashboard is adequately shielded from this device RF
energy.
Condions of Use
• Indoor use only.
• Do not allow your devicve to be exposed to adverse weather or

17
environmental condions (moisture, humidity, rain, inltraon of
liquids, dust, sea air, etc.).
• When this device is switched on, it should be kept at least 20 cm
from the body.
• When this device is switched on, it should be kept at least 15 cm
from any medical device such as a pacemaker, a hearing aid or
insulin pump, etc.
• When replacing the cover, please note that this device may con-
tain substances that could create an allergic reacon.
• Do not paint it.
• The manufacturer’s recommended operang temperature range
is 0°C to +45°C.
• Always handle this device with care and keep it in a clean and
dust-free place.
• Clean this device with a dry cloth only.
• Do not aempt to disassemble or repair this device or its acces-
sories.
• Do not drop, throw or bend this device.
• Do not let children use this device and/or play with the this de-
vice and accessories without supervision.

18
Cercaon
This symbol on the device means that these products must
be taken to collecon points at the end of their life:
- Municipal waste disposal centres with specic bins for
these items of equipment.
- Collecon bins at points of sale.
They will then be recycled, prevenng substances being disposed
of in the environment and allowing their components to be reused.
In European Union countries:
These collecon points are accessible free of charge.
All products with this sign must be brought to these collecon points.
In non European Union jurisdicons:
Items of equipment with this symbol are not to be thrown into
ordinary bins if your jurisdicon or your region has suitable recycling
and collecon facilies; instead they are to be taken to collecon
points for them to be recycled.
CHARGERS
Mains powered chargers will operate within the temperature range
of: 0°C (32°F) to 40°C (104°F ).

19
The chargers designed for your device meet the standard for safety
of informaon technology equipment and oce equipment use.
They are also compliant with the ecodesign direcve 2009/125/EC.
Due to dierent applicable electrical specicaons, a charger you
purchased in one jurisdicon may not work in another jurisdicon.
They should be used for this purpose only.
Characteriscs of power supply (depending on the country):
Charger: Input: 100-240 V, 50/60 Hz, 500 mA
Output: 5V, 2A
Radio Waves
THIS DEVICE MEETS THE GOVERNMENT’S REQUIREMENTS FOR
EXPOSURE TO RADIO WAVES.
Your device is a radio transmier and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to
radio-frequency (RF) energy. These limits are part of comprehensive
guidelines and establish permied levels of RF energy for the
general populaon. The guidelines are based on standards that were
developed by independent scienc organizaons through periodic
and thorough evaluaon of scienc studies. These guidelines
include a substanal safety margin designed to ensure the safety of
all persons, regardless of age and health.

20
The World Health Organizaon (WHO) considers that present
scienc informaon does not indicate the need for any special
precauons for use of wireless devices. If individuals are concerned,
they might choose to limit their own or their children’s RF exposure
by liming the length of use to keep device away from the head
and body. Addional WHO informaon about electromagnec elds
and public health are available on the following website: hp://www.
who.int/peh-emf.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instrucons, may cause
harmful interference to radio communicaons. However, there is no
guarantee that interference to radio or television recepon, which
can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna;
- Increase the separaon between the equipment and receiver;
- Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected;