TECHLIGHTING GIA MIRROR KIT User manual

1
GP I :ENERAL RODUCT NFORMATION
Suitable for damp locations.
Install the Fixtures
1A
2
1Ensure that the electrical box is located behind the mirror location.
-For multiple mirror installations, an electrical box must be present behind the mirror which is the center of the group.
-For multiple mirror installations with 600 lms/ft, two electrical boxes must be present behind each outer mirror to support
the additional driver.
Using the provided cardboard mirror template and a fixture; level, measure, and mark the location of mirror(s) and fixtures.
CAUTION - RISK OF FIRE
This product must be installed in accordance with the
applicable installation code by a person familiar with the
construction and operation of the product and the
hazards involved.
Use minimum 90°c supply conductors.
CAUTION: It is important to determine the location of
the electrical box/driver and fixture layout before
beginning the following installation.
2
5
3
5
3
5
3
MULTIPLE MIRROR INSTALLATION
MULTIPLE MIRROR WITH 600 LMS/F INSTALLATION
1
1 1
2
2
2
BCATH OLLECTION
5
3
2
1
ELECTRICAL
BOX
CARDBOARD TEMPLATE
36.5”
24”
1.2
Installation Instructions for
Gia Mirror Kit
700BCGIAMR_
920BCGIADM

2
7Replace the fixtures and secure them by tightening the
#8 screw it into the anchors.
NOTE: For multiple mirror installations, install the
fixtures in an order that ensures that all the fixture wires
are able to reach the nearest electrical box while being
tightly installed under the fixture that is before it if
necessary. See illustrated install order examples.
1C
5
3
At a bracket hole location, push the anchor into the
wall up to the threads.
Screw the anchors in the rest of the way with a Phillips-
head screwdriver.
Repeat steps 4-5 for the other anchors.
24
6
66
ANCHOR
4
25
26
1D
5
3
1B
5
3
FIXTURE BRACKET
Place the fixture on the marked location and mark the
location of the holes in the fixture’s mounting bracket.
Note: Ensure that the brackets are located behind the
mirror
FIXTURE
23
SCREW
23
3
23
23
7
7
8
8
5
3
5
3
1 2 34
FIXTURE
WIRE
TUCKED
UNDER
FIXTURE
WIRE
TUCKED
UNDER
21 3
FIXTURE
WIRE
TUCKED
UNDER

3
10
5
3
5
3
MOUNTING PLATE
Properly place the driver, input wires, and wire nut
connections into the electrical box.
Feed the fixture wires through the mounting plate
center hole. Ensure that the fixture wires fromNote:
each fixture remain separate and identifiable for power
connections.
2
12
13
Wiring for all except 600lms/f 2 and 3 mirror:
Properly connect each of the driver wires to one of the
fixture wires from each fixture.
Wiring for 600lms/f 2 and 3 mirror:
Properly connect each of the driver wires to one of the
fixture wires in way that the each driver is only
connected to a maximum of two fixtures.
1G
2 MIRROR WITH 600 LMS/F INSTALLATION
3 MIRROR WITH 600 LMS/F INSTALLATION
1E
2
8
5
3
9
5
3
Connect the white driver wire to the neutral power line.
Connect the black driver wire to the hot power line.
Note: For 600 lms/f installations, wire each driver
separately to the power lines from its dedicated
electrical box.
8
9
1F
5
3
5
3
3
5
3
5
3
5
5
3
5
3
5
3
5
3
11
11
12
12
12
12
13
13
13
13
13 13
13 13
SINGLE DRIVER
SINGLE DRIVER
DRIVER #1 DRIVER #2
DRIVER #1 DRIVER #2

4
1H
14
5
3
5
3
MOUNTING PLATE
#8-32 SCREW
Properly place the wires and wire nut connections inside
the electrical box.
If necessary, push any excess fixture wire into the
electrical box through the mounting plate.
Attach the mounting plate to the electrical box using
the two #8-32 screws provided.
For 600 lms/f installations, repeat for the other electrical
box.
15
16
17

Install the Mirror
2A
1
5
3
5
3
Align the inner edge of the mirror bracket base to the
edge of the mirror markings and mark the location of
the holes in the mirror’s mounting bracket base. Note:
Ensure that the brackets are leveled and aligned
vertically.
MIRROR BRACKET BASE
INNER EDGE
1 1
1
2B
5
3
5
3
4 4
4
At a bracket hole location, push the anchor into the
wall up to the threads.
Screw the anchors in the rest of the way with a Phillips-
head screwdriver.
Repeat steps 2-3 for the other anchors.
22
ANCHOR
2
23
24
5Replace the mirror bracket bases and secure them by
tightening the #8 screw it into the anchors.
2C
5
3
5
3
5 5
5
5
5
6With the provided Allen wrench, ensure that the set
screws in the mirror bracket base are backed out.
2D
5
3
5
3
6
6
SCREW
ALLEN
WRENCH
SET SCREW
6
6

7Install mirror brackets only into the lower mirror
bracket bases.
Tighten the set screws.
2E
5
3
5
3
8
7
8
9Gently slide the mirror into the assembled lower
brackets.
2F
5
3
5
3
MIRROR BRACKET
MIRROR BRACKET
MIRROR
10 Install the top mirror brackets into the bases and
tighten the set screws.
2G
5
3
5
3
65

7

SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
© 2014 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
8