TechNexion TOUCAN TC-0710 SLIM HMI User manual

TOUCAN TC-0710 SLIM HMI PRODUCT MANUAL
(TC-0710)
VER. 1.00
July 27, 2018

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 2of 26
REVISION HISTORY
Revision
Date
Originator
Notes
1.00
July 27, 2018
TechNexion
First public release

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 3of 26
TABLE OF CONTENTS
1. Introduction ...............................................................................................................................................4
1.1. General Care and Maintenance .........................................................................................................4
2. TC-0710 Product Overview.......................................................................................................................5
2.1. Functional Block Diagram ..................................................................................................................5
2.2. Dimensions.........................................................................................................................................6
2.3. Device Cut-out Dimensions For Mounting Though a Panel...............................................................7
2.4. External Connectors...........................................................................................................................8
2.5. Internal Board Connectors ...............................................................................................................10
3. External Connectors................................................................................................................................12
3.1. Gigabit Ethernet Interface.................................................................................................................12
3.2. Power Input Connector.....................................................................................................................12
3.3. Digital I/O Connector (GPIO)............................................................................................................13
3.4. USB Host Connector........................................................................................................................13
3.5. HDMI (High Definition Multi-Media Interface)...................................................................................13
3.6. CAN Bus Connector (CANBus)........................................................................................................14
3.7. Serial Port / MDB Connector (RS-XXX)...........................................................................................15
3.8. USB OTG Connector........................................................................................................................16
3.9. MicroSD Connector..........................................................................................................................17
3.10. S1 Button........................................................................................................................................17
3.11. RST Button.....................................................................................................................................17
3.12. Antenna Holes................................................................................................................................17
4. Internal Connectors and Expansion Options ..........................................................................................18
4.1. RTC Battery Connector....................................................................................................................18
4.2. Audio Connectors.............................................................................................................................19
4.3. Power Fuse ......................................................................................................................................19
4.4. S1 Button Boot Select Mode DIP Switch..........................................................................................19
5. Mounting..................................................................................................................................................20
5.1. VESA Mounting................................................................................................................................20
5.2. Rear Mounting and Mounting Clips Installation................................................................................21
5.3. Surface Mounting and O-ring Installation.........................................................................................22
6. Ordering Information...............................................................................................................................23
6.1. Custom Part Number Rule ...............................................................................................................23
6.2. Standard Package Contents ............................................................................................................24
7. Important Notice......................................................................................................................................25
8. DISCLAIMER ..........................................................................................................................................26

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 4of 26
1. Introduction
1.1. General Care and Maintenance
Your device is a product of superior design and craftsmanship and should be treated with care.
The following suggestions will help you.
•Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain
minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely.
•Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be
damaged.
•Do not store the device in hot areas. High temperatures can shorten the life of electronic devices,
damage batteries, and warp or melt certain plastics.
•Do not store the device in cold areas. When the device returns to its normal temperature,
moisture can form inside the device and damage electronic circuit boards.
•Do not open the device while power is on. Otherwise electrical shock may result.
•Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and
fine mechanics.
•Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
•Do not paint the device. Paint can clog the moving parts and prevent proper operation.
•Unauthorized modifications or attachments could damage the device and may violate regulations
governing radio devices.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is
not working properly, take it to the nearest authorized service facility for service.
Regulatory information
Disposal of Waste Equipment by Users in Private Household in the European Union
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose
of your waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
We hereby declare that the product is in compliance with the essential requirements and
other relevant provisions of European Directive 1999/5/EC (radio equipment and
telecommunications terminal equipment Directive).

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 5of 26
2. TC-0710 Product Overview
2.1. Functional Block Diagram

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 6of 26
2.2. Dimensions
The following figure shows the TC-0710 dimensions (unit: mm):

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 7of 26
2.3. Device Cut-out Dimensions For Mounting Though a Panel
The TC-0710 can be mounted on the front or the back of the panel. In order to mount it from the front, a
nominal rectangular cutout must be made in the panel. The following drawing shows the dimensions of
the cut-out area (unit: mm):

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 8of 26
2.4. External Connectors
The TC-0710 has a number of external connectors.
Rear view:
11
10
9
8
1 2 3 4 5 6 7
External Connectors:
No.
Description
No.
Description
1
LAN RJ45 and PoE connector
7
Serial Port (RS-XXX) connector
2
Power Input (10~30VDC) connector
8
MicroSD cardslot
3
GPIO connector
9
USB OTG connector
4
USB Host connector
10
S1 Boot Select button
5
HDMI connector
11
Reset button
6
CAN Bus (CANBus) connector

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 9of 26
Bottom view:
1 2 3 4 5 6 7
Right side view:
8 8 910 11
External Connectors:
No.
Description
No.
Description
1
LAN RJ45 and PoE connector
7
Serial Port (RS-XXX) connector
2
Power Input (10~30VDC) connector
8
MicroSD cardslot
3
GPIO connector
9
USB OTG connector
4
USB Host connector
10
S1 Boot Select button
5
HDMI connector
11
Reset button
6
CAN Bus (CANBus) connector

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 10 of 26
2.5. Internal Board Connectors
The TC-0710 has several connectors, switches and internal expansion options. It is necessary to remove
the EDM computing module to access several switches, headers and connectors.
Rear view (opened device) with the EDM computing module:
A
EDM Computing Module
B
C
E
GD
F
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
E
USB (2 port) header
B
Mic in connector
F
USB (shared with touchpanel)
C
Line out connector
G
Power Fuse
D
SW1 DIP switch for RS-XXX Serial Port

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 11 of 26
Rear view (opened device) without the EDM computing module:
A
H*
B
C
E I* D
G
F
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
F
USB (shared with touchpanel)
B
Mic in connector
G
Power Fuse
C
Line out connector
H*
Boot Select switch for S1 button
D
SW1 DIP switch for RS-XXX Serial Port
I*
SW2 MDB
E
USB (2 port) header
NOTE: Items marked with * are accessible only after removing the EDM computing module.

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 12 of 26
3. External Connectors
3.1. Gigabit Ethernet Interface
The TC-0710 by default comes with a single Gigabit Ethernet RJ45 connector. This connector can
support 802.3at Power over Ethernet functionality by connecting it to an 802.3at compliant PoE switch or
power injector.
Pin #
1000 Mbps
100 Mbps
10 Mbps
1
MDI0+
Transmit Data+
Transmit Data+
2
MDI0-
Transmit Data-
Transmit Data-
3
MDI1+
Receive Data+
Receive Data+
4
MDI2+
5
MDI2-
6
MDI1-
Receive Data-
Receive Data-
7
MDI3+
8
MDI3-
3.2. Power Input Connector
The TC-0710 can be powered either over the DC INPUT connector or PoE over the RJ45 LAN port.
NOTE: Do not power the unit by DC input when you apply power over the Power over Ethernet (RJ45)!
Pin #
Signal
Description
1
GND
Ground
2
VCC
DC Voltage input (10~30VDC)
Header on TC-0710: Molex 43045-0200 (2-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0200 (2-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 13 of 26
3.3. Digital I/O Connector (GPIO)
The TC-0710 has one galvanic isolated GPIO Expansion header with the following pinout:
GPIO:
Pin
#
Signal
Description
Voltage
Current
Max.
GPIO
Kernel
GPIO
Bank/IO
Min.
Typ.
Max.
1
GPIO1A
DIG_IN1
1.2V
1.4V
1A
90
6_31
2
GPIO1B
DIG_IN2
1.2V
1.4V
1A
191
3_26
3
GND_DIO
Ground for digital I/O
4
GND
Common Ground
5
GPIO1C
DIG_OUT5
5V
34V
1A
163
6_03
6
GPIO1D
DIG_OUT6
5V
34V
1A
24
1_24
7
VCC_DIO
Supply input for digital I/O
5V
34V
8
VCC*
Supply output
10V
30V
NOTE: * VCC supply output is based on the VDC input. There is no supply output when device is
powered over the Power over Ethernet (RJ45)!
Header on TC-0710: Molex 43045-0800 (8-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
3.4. USB Host Connector
The TC-0710 has a standard single USB Host connector (USB 2.0 signals only) to connect to a USB
peripheral such as a keyboard, mouse, USB storage device or USB hub.
3.5. HDMI (High Definition Multi-Media Interface)
The HDMI interface available on the TC-0710 is based on the “HDMI transmitter” & “HDMI 3D TX PHY”
integrated into the NXP i.MX6 processor and can be configured to support a secondary display.
The HDMI supports the following standards & features:
•High-Definition Multimedia Interface Specification, Version 1.4a
•Digital Visual Interface, Revision 1.0
•HDMI Compliance Test Specification, Version 1.4a
•Support for up to 720p at 100Hz and 720i at 200Hz or 1080p at 60Hz and 1080i/720i at 120Hz
HDTV display resolutions and up to QXGA graphic display resolutions.
•Support for 4k x 2k and 3D video formats
•Support for up to 16-bit Deep Color modes
For additional details, please refer to the “EDM1-CF-IMX6 Hardware Manual”.

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 14 of 26
3.6. CAN Bus Connector (CANBus)
The TC-0710 has two galvanic isolated CAN Bus interfaces with the following pinout:
CANBus:
Pin #
Signal
Description
Interface
1
GND_CAN
Ground for CAN
2
CAN1A_TERM_P
To enable CAN1A Termination, bridge with CAN1A_P
can0
3
CAN1A_P
CAN Bus 1A high (-24~+24V)
can0
4
CAN1A_N
CAN Bus 1A low (-24~+24V)
can0
5
CAN1A_TERM_N
To enable CAN1A Termination, bridge with CAN1A_N
can0
6
NC
7
GND_CAN
Ground for CAN
8
CAN1B_TERM_P
To enable CAN1B Termination, bridge with CAN1B_P
can1
9
CAN1B_P
CAN Bus 1B high (-24~+24V)
can1
10
CAN1B_N
CAN Bus 1B low (-24~+24V)
can1
11
CAN1B_TERM_N
To enable CAN1B Termination, bridge with CAN1B_N
can1
12
NC
Header on TC-0710: Molex 43045-1200 (12-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1200 (12-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 15 of 26
3.7. Serial Port / MDB Connector (RS-XXX)
The TC-0710 has dual 4-wire galvanic isolated serial port that can be configured as follows: The primary
serial port can only be used as a standard RS-232. The secondary port can be configured either as RS-
232, RS-422, RS-485 or utilize MDB protocol. This serial port is set by default as RS-232. Setting the TC-
0710 in other mode will require to open the device and adjust the internal SW1 DIP and SW2 switch
settings on the Toucan circuit board. The SW1 DIP switch can be found at location “E” and SW2 at
location “F” in chapter 2.5. Internal Board Connectors of this manual.
SW1:
Pin #
RS-232 (default)
RS-422
RS-485
MDB
1-8
ON
OFF
OFF
OFF
2-7
OFF
ON
OFF
OFF
3-6
OFF
OFF
ON
OFF
4-5
OFF
ON
ON
OFF
SW2:
Pin #
RS-232 (default)
RS-422
RS-485
MDB
1-2
OFF
OFF
OFF
ON
RS-232 + RS-232 (default setup):
Pin #
Signal
Description
Device
1
GND
Ground
2
SERIAL1A_TXD
Port#1A Transmit data (output)
ttymxc0
3
SERIAL1A_RXD
Port#1A Receive data (input)
ttymxc0
4
SERIAL1A_RTS
Port#1A Request-to-send (output)
ttymxc0
5
SERIAL1A_CTS
Port#1A Clear-to-send (input)
ttymxc0
6
GND
Ground
7
SERIAL1B_TXD
Port#1B Transmit data (output)
ttymxc1
8
SERIAL1B_RXD
Port#1B Receive data (input)
ttymxc1
9
SERIAL1B_RTS
Port#1B Request-to-send (output)
ttymxc1
10
SERIAL1B_CTS
Port#1B Clear-to-send (input)
ttymxc1
RS-232 + RS-422:
Pin #
Signal
Description
Device
1~5
SERIAL1A
Identical as above
ttymxc0
6
GND
Ground
7
SERIAL1B+
RS-485 positive data signal
ttymxc1
8
NC
9
NC
10
SERIAL1B-
RS-485 negative data signal
ttymxc1

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 16 of 26
RS-232 + RS-485:
Pin #
Signal
Description
Device
1~5
SERIAL1A
Identical as above
ttymxc0
6
GND
Ground
7
SERIAL1B+
RS-485 positive data signal
ttymxc1
8
NC
9
NC
10
SERIAL1B-
RS-485 negative data signal
ttymxc1
RS-232 + MDB:
Pin #
Signal
Description
1~5
SERIAL1A
Identical as above
6
GND
Ground
7
MDB_TXD
MDB transmit data signal (output)
8
MDB_RXD2
MDB receive data signal (input)
9
MDB_WakeUp
MDB wakeup signal (output)
10
MDB_VCC
MDB wakeup pull up VCC (0~5V)
Header on TC-0710: Molex 43045-1000 (10-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
3.8. USB OTG Connector
The TC-0710 has one USB OTG connector (USB 2.0 signals only) that can be used to connect a host
computer to the unit for programming and update purposes.
Pin #
Signal
Description
1
VBUS
5V Universal Serial Bus Power
2
USB_D-
Universal Serial Bus differential pair signal
3
USB_D+
4
USB_OTG_ID
Universal Serial Bus On-The-Go detection signal
5
GND
Ground
6
NC
7
NC
8
GND
Ground
9
NC
10
NC

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 17 of 26
3.9. MicroSD Connector
The TC-0710 features a standard microSD cardslot which is connected to the NXP i.MX6 integrated “Ultra
Secured Digital Host Controller” (uSDHC).
The following main features are supported by uSDHC:
•Compatible with the MMC System Specification version 4.2/4.3/4.4/4.41/5.0.
•Conforms to the SD Host Controller Standard Specification version 3.0.
•Compatible with the SD Memory Card Specification version 3.0 and supports the “Extended
Capacity SD Memory Card”.
•Compatible with the SDIO Card Specification version 3.0.
•Supports 1-bit / 4-bit SD and SDIO modes
The MMC/SD/SDIO host controller can support a single MMC / SD / SDIO card or device.
3.10. S1 Button
The TC-0710 by default boots the unit from internal flash storage (eMMC). By pressing the “S1” button
before applying power to the unit and keeping the button pressed for 10 seconds, the unit will boot from
an alternative boot media, such as a microSD card. The primary and alternative booth media are
determined by internal DIP switch settings. Please see section 4.4. S1 Button Boot Select Mode DIP
Switch for more details.
3.11. RST Button
The TC-0710 features a “RST” button for system reset.
3.12. Antenna Holes
There are two antenna holes available (on the top side). They come fitted with breakaway metal tabs. In
order to utilize them, the tabs must be removed by carefully using pincers or pliers.

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 18 of 26
4. Internal Connectors and Expansion Options
Rear view (opened device) without the EDM computing module:
A
H*
B
C
E I* D
G
F
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
F
USB (shared with touchpanel)
B
Mic in connector
G
Power Fuse
C
Line out connector
H*
Boot Select switch for S1 button
D
SW1 DIP switch for RS-XXX Serial Port
I*
SW2 MDB
E
USB (2 port) header
NOTE: Items marked with * are accessible only after removing the EDM computing module.
4.1. RTC Battery Connector
The TC-0710 has an internal RTC backup battery connector (Marked A).
Pin #
Signal
Description
1
GND
Ground
2
RTC_VCC
3V (connect to standard CR2032 battery)

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 19 of 26
4.2. Audio Connectors
The TC-0710 has two internal audio connectors to connect a passive microphone or a speaker (Marked B
and C respectively) The line out signal is pre-amplified with a 2W Texas Instruments TPA2025D1
amplifier.
Mic in (Marked B):
Pin #
Signal
Description
1
MIC
Microphone Signal
2
AGND
Microphone Ground Signal
Line out (Marked C):
Pin #
Signal
Description
1
SP+
Speaker Positive Signal
2
SP-
Speaker Analog Ground Signal
4.3. Power Fuse
The TC-0710 features a fast-acting square ceramic surface mount fuse Conquer SEF3A125V (Marked G)
The fuse has the following current and voltage ratings: 3A at 125V.
4.4. S1 Button Boot Select Mode DIP Switch
The TC-0710 has an internal S1 Button Boot Mode Select DIP switch (Marked H).
Pin #
Boot from SD (default)
Boot from iNAND
1
ON
OFF
2
ON
OFF
3
OFF
ON
4
OFF
ON
5
OFF
ON
6
OFF
OFF

TC-0710 HARDWARE MANUAL –VER 1.00 –JUL 27 2018
Page 20 of 26
5. Mounting
This section describes the mounting procedures for TC-0710. The material in area of the mounting must
provide sufficient strength for safe mounting of this device.
5.1. VESA Mounting
The TC-0700 is compatible with the VESA MIS-C Standard 35*75mm hole pattern. There are 4 VESA
MIS-C (M4) mounting holes on the rear side of the device. M4 screw holes are a depth of 6mm.
1 2
3 4