TECHNOFASE RDM BK43-1A User manual

Technical Manual Page 1 of 17
www.technofase.com
RDM BK43
Valid for versions RDM BK4 - 1A
RDM BK4 - A
RDM BK4 - B
RDM BK4 – 6B
RDM BK4 – 9A

Technical Manual Page 2 of 17
www.technofase.com
GENERAL INDEX
Foreword....................................................................................4
1. Safety instr ctions for the ser and safety meas res
for the RDM BK43 system .......................................................5
S pplementary notes for RADIO interface appliances ......6
2. Introd ction..........................................................................7
2.1 Environmental characteristics.......................................................................... 7
3. Compliance with the standard...........................................7
3.1 Reference Standard .............................................................................................. 8
.2 CEPT 70-0 Recommendation ....................................................................... 9
. Identification......................................................................................................9
4. Technical data.....................................................................10
4.1 Models available .............................................................................................. 10
4.2 Standard radio channels.................................................................................11
4. Communication interfaces.............................................................................. 12
4.4 Power supply ................................................................................................... 12
4.5 Connections...................................................................................................... 12
5. Assembly specifications....................................................13
5.1 External assembly .......................................................................................... 13
5.2 Assembly inside an electrical panel.............................................................13
6. B tton f nctions.................................................................14
7. Labelling of the vario s models.......................................15
7.1 RDM BK4 - A Label........................................................................................15
7.2 RDM BK4 - B Label........................................................................................15
7. RDM BK4 -6B Label........................................................................................15
7.4 RDM BK4 -9A Label........................................................................................15
8. Prod ct g arantee .............................................................16

Technical Manual Page of 17
www.technofase.com
8.1 Terms of the guarantee..............................................................................16
9.1 Standard concerning disposal ...................................17
Manufacturer .......................................................................................................... 17

Technical Manual Page 4 of 17
www.technofase.com
Foreword
• This manual contains text, images and explanations for the correct
installation and use of the RDM BK4 transceiver. It should be read and
understood before the appliance is installed and used.
• This manual has been published subject to alteration. We reserve the right to
modify this manual without prior notice.
• As the system works by means of radio waves, transmission may, in certain
cases, be influenced by the environment and by the method of use. The
manufacturer is not liable for any damage to persons and/or appliances.
• Do not use the system near other appliances operating with radio waves as
this could cause malfunctioning.
IMPORTANT
• Do not remove or replace any parts of the system.
• Do not remove, alter or modify the identification plate on the back of the
system. It is forbidden to use the system without identification plates.
Hardware Manual
Revision: B.0
Date: 06/2007

Technical Manual Page 5 of 17
www.technofase.com
1. Safety instr ctions for the ser and safety meas res
for the RDM BK43 system
This manual has been drawn up for use by trained and competent personnel.
The qualification of the personnel is defined in the European Directives on
machines, low voltage and EMV. All the electrical connections of RDM BK4
systems must be carried out by a technician who has specific training in local
and national electrical standards. Several symbols are used in this manual to
highlight certain information. The purpose of these symbols is to draw the
attention of personnel involved to warnings concerning safety and to safety
measures. Whenever a symbol appears, the relevant note should be read and
the information followed carefully.
This symbol indicates an imminent danger causing damage to persons
or property.
This symbol indicates a danger that could cause damage to persons or
property.
This symbol indicates the need to check the harmonization for the use
of radio frequency.

Technical Manual Page 6 of 17
www.technofase.com
• TECHNOFASE cannot be held responsible for damage due to inappropriate
installation or operation of the appliances.
• Do not replace the electrical components or attempt to repair products of the
RDM BK4 series in any way.
• The products of the RDM BK4 series must be used in accordance with the
relevant local and national standards in force.
S pplementary notes for RADIO interface appliances
The products with radio interface have been designed to operate on UHF radio
frequencies (4 – 4 6MHz) that vary from one country to another. The user
must take care to check the standards in force in the country in which the
appliance is being used before putting it into use.
Contact the local Ofcom (Office of Communications) agency to obtain a licence
or further information concerning the limitations on the free, unrestricted use
(SRD) of the appliance.

Technical Manual Page 7 of 17
www.technofase.com
2. Introd ction
The RDM BK4 system has been developed for transmitting and receiving data
via radio.
The special features of the RDM BK4 system are the following:
• Considerable immunity to disturbances
• Compact size
• IP65 die-cast aluminium casing
• Easily accessible RS2 2 communication port
• Up to 16 programmable channels that can be set using the buttons
• Power supply ranging from 10 to 15V
• Built-in flexible antenna ¼
2.1 Environmental characteristics
• Operating temperature -20 / 50 °C
• Storage temperature -25 / 50 °C
• Relative humidity 5-85%, without condensation
• Vibration resistance

Technical Manual Page 8 of 17
www.technofase.com
3. Compliance with the Standard
The system complies with the following harmonised standards:
• EN 61000-6-1 Immunity to disturbances
• EN 61000-6- Immunity to disturbances
• EN 50082-2 Conducted emissions
• EN 60950 Electrical safety
• EN 01-489-1 + EN 01-489- Radio appliances
• EN 00-220-1 + EN 00-220- ISM Band SRD
• EN 00-296-2
3.1 Reference Standard
The RDM BK4 transceiver complies with the following European standards:
EN 300 220, EN 301 489, EN 300 296.
Furthermore, the product has been tested according to standard EN 60950.

Technical Manual Page 9 of 17
www.technofase.com
3.2 CEPT 70-03 Recommendation
The RDM BK4 product operates on a harmonised frequency band and
therefore, to comply with the standard in force, it must be used, on the time
scale, for 10% max. of an hourly duty cycle (corresponding to 6 minutes of
use per hour).
NOTE: In view of the constr ction system, the ser is responsible for
compliance with this parameter.
3.3 Identification
The product is identified by the product identification number and a seven-
digit number (representing the series number and year of manufacture) on the
casing.

Technical Manual Page 10 of 17
www.technofase.com
4. Technical data
Make TECHNOFASE
Model BK4 -XX
Channels Selectable, up to 24
Max. RF power 500mW ERP
Frequency stability +/- 1 KHz
Power supply 10-15V DC
Operating temperature -20 / 50 °C
Sizes excluding
antenna
150 x 64 x 6 mm
4.1 Models available
The models vary according to the frequency band and the antenna power
RDM BK4 Mod. A 4 .175 - 4 4.675MHz
500mW ERP
1
RDM BK4 Mod. C 4 .050 - 4 9.420MHz 500mW ERP
1
RDM BK4 Mod. B 4 .050 - 4 4.790MHz 10mW ERP
2
RDM BK4 Mod. 6B 4 6.000 - 4 6.100MHz 500mW ERP
RDM BK4 Mod. 9A 4 9.700 - 4 9.975MHz 500mW ERP
4
RDM BK4 Mod. 1A 441.025 - 441.775MHz 500mW ERP
5
1)
This model can only be used in Austria and Switzerland after payment of the local licence fee.
2)
This model can only be used in countries in which this power limit is applied. Check with the
competent Office of Communications for possible use.
)
This model can only be used in Italy according to the frequency assignment plan, point 101A,
after filing a general a thorisation application as set out in Presidential Decree no. 447 of 5
October 2001, Art. 5, Para. 1, Point 2, and after payment of the relevant fee. Contact the local
department of the Office of Communications for further information concerning its use.
4)
This model can only be used in Sweden in compliance with the country’s regulations.
5)
This model can only be used in Norway in compliance with the country’s regulations.

Technical Manual Page 11 of 17
www.technofase.com
4.2 Standard radio channels
BK4 - A
25KHz
BK4 - C
25KHz
BK4 -6B
12.5KHz
BK4 -9A
25KHz
BK4 -1A
12.5KHz
CH 1 4 .825 4 .825 4 6.00625 4 9.700 441.0250
CH 2 4 .875 4 .875 4 6.01875 4 9.725 441.0750
CH 4 .925 4 .925 4 6.0 125 4 9.750 441.1250
CH 4 4 .975 4 .975 4 6.04 75 4 9.775 441.1750
CH 5 4 4.025 4 4.025 4 6.05625 4 9.800 441.2250
CH 6 4 4.075 4 4.075 4 6.06875 4 9.825 441.2750
CH 7 4 4.125 4 4.125 4 6.08125 4 9.850 441. 250
CH 8 4 4.175 4 4.175 4 6.09 75 4 9.875 441. 750
CH 9 4 .825
12 4 .825 12 4 6.00625 12 4 9.900 441.4250
CH 10 4 .875
12 4 .875 12 4 6.01875 12 4 9.925 441.4750
CH 11 4 .925
12 4 .925 12 4 6.0 125 12 4 9.950 441.5250
CH 12 4 .975
12 4 .975 12 4 6.04 75 12 4 9.975 441.5750
CH 1 4 4.025
12 4 4.025 12 4 6.05625 12 441.6250
CH 14 4 4.075
12 4 4.075 12 4 6.06875 12 441.6750
CH 15 4 4.125
12 4 4.125 12 4 6.08125 12 441.7250
CH 16 4 4.175
12 4 4.175 12 4 6.09 75 12 441.7750
CH 17 4 .900 4 .900 4 6.00625
CH 18 4 .950 4 .950 4 6.01875
CH 19 4 4.100 4 4.100 4 6.0 125
CH 20 4 4.150 4 4.150 4 6.04 75
CH 21 4 4.200 4 4.200 4 6.05625
CH 22 4 4.400 4 9. 90 4 6.06875
CH 2 4 9.410 4 6.08125
CH 24 4 9.4 0 4 6.09 75

Technical Manual Page 12 of 17
www.technofase.com
4.3 Comm nication interfaces
RS2 2 RS2 2 standard interface
Mini DIN 6 F type connection
4.4 Power s pply
The RDM BK4 transceiver must be run on a very low safety voltage
supply protected against short circuits.
Supply voltage: 10-15V
Maximum absorption in Tx: 400 mA
Protection against short circuits: Polyswitch
Type: Resettable RXE040
4.5 Connections
For external connections, a screened cable with a MINIDIN 6 type
connector has been provided both for data and for the power supply.
All electrical connections are designed for lengths up to a max. of m.

Technical Manual Page 1 of 17
www.technofase.com
5. Assembly specifications
5.1 External assembly
External assembly can be carried out using a support plate with a 24
mm hole in the centre. This plate must then be fixed to a suitable
means of support.
5.2 Assembly inside an electrical panel
For assembly inside an electrical panel, a hole 24 mm in diameter must
be drilled to allow the antenna to transmit and receive outside. The
earthing surface must be at least 20cm x 20cm in size.

Technical Manual Page 14 of 17
www.technofase.com
6. B tton f nctions
Three rubber buttons are located in the lower part to set the channel and to
switch the appliance on/off.
The display shows the number of the channel currently set. To change
channels, press the CHANNEL button until the number shown on the display
starts flashing (ACTUAL CHANNEL): then press the INCREMENT button to
increase the channel number. To lower the number continue pressing the
button until the last channel (24) is reached and the system starts again from
1. After setting the channel, press the CHANNEL button again until the flashing
stops. The TX/RX LED indicates reception when green and transmission when
red.

Technical Manual Page 15 of 17
www.technofase.com
7. Labelling of the vario s models
7.1 RDM BK43-3A label
7.2 RDM BK43-3B label
7.3 RDM BK43-6B label
7.4 RDM BK43-9A label

Technical Manual Page 16 of 17
www.technofase.com
8. Prod ct g arantee
8.1 Terms of the g arantee
8.2.1 GUARANTEE AND CONDITIONS
Technofase products are covered by a 2 (TWO) YEAR guarantee from the date of
purchase with the exception of the batteries which are covered by a 6 (SIX) MONTH
guarantee. During this period Technofase undertakes, at its sole discretion, to repair or
replace faulty components with similar or equivalent products or to refund the
Customer for the amount paid for the component in the case of faulty material or
manufacturing defects. If the label with the series number of a product has been
cancelled, tampered with, or partially or completely covered, Technofase reserves the
right not to consider such a product under guarantee. The guarantee covers
manufacturing faults in the components at the time of purchase and the labour
necessary to repair them.
The guarantee is null and void in the event of: improper use of the product, negligence,
intentional damage or any problem due to incorrect installation after purchase. The
guarantee is of the “on-centre” type, i.e. the customer is only liable for paying the cost
of dispatching the faulty product to the repair shop.
8.2.2 DURATION OF THE GUARANTEE FOLLOWING SERVICES UNDER THE
GUARANTEE
Any service carried out under the guarantee will not prolong the duration of the
guarantee.
8.2. RESPONSIBILITY TOWARDS THIRD PARTIES
The buyer will not hold Technofase responsible with regard to any controversy that
may arise with the final user as the buyer undertakes to check in advance the
appropriateness of the system configuration and of every single component he has
purchased. It is expressly understood that Technofase is responsible only towards the
first buyer and exclusively within the terms provided for by the guarantee clause.

Technical Manual Page 17 of 17
www.technofase.com
9.1 Standard concerning disposal
EC-Directive 2002/96 Waste electrical and electronic appliances –
RAEE.
This product complies with EU Directive 2002/96/EC.
The symbol of the crossed litter bin appearing on the appliance
indicates that at the end of its useful life the product must be
disposed of separately from household waste. The user is responsible
for taking the appliance to a suitable collection point at the end of its
life. Separate waste collection and subsequent recycling, processing and the eco-
friendly disposal of exhausted appliances contribute towards preventing negative
effects on the environment and on health and help to recycle the materials of which the
product is made. Contact the local waste disposal service or the shop in which the
product was purchased for more detailed information concerning the collection systems
available.
Man fact rer
RDM BK4 is made by:
TECHNOFASE
Via GALVANI 2
9100 BOLZANO
Tel [phone]
Fax [phone]
[email protected]om
THE TERMS AND CONDITIONS IN THIS DOCUMENT MAY BE CHANGED WITHOUT PRIOR NOTICE.