tecnoswitch TE035BI User manual

WALL MOUNTED TOUCH THERMOSTAT

Congratulations for purchasing the TE035BI.
To get the maximum performance, please to read carefully all the instructions.
The thermostat guarantees the best comfort temperature, thanks to easy programming
and intuitive graphics interface.
It’s supplied with an in-cell touch display with back-lighting that it is the most advanced of the
wall-mounted category.
The touch display makes it intuitive, easy to program and unique.
The strengths are:
Ease of use;
The high quality of Made in Italy
Design with attention to the smallest details;
Super-capacitor technology to keep data in memory.
WALL MOUNTED TOUCH THERMOSTAT

KEYS LEGEND
DISPLAY LEGEND
Menu
Increase
Decrease
Confirm
Scrools the next icon
ON/OFF - Manual/Automatic
Energy consumption savings indicator
Set temperature
Cooling time
Heating
Temperature
Set Reduction temperature ON
Set Comfort temperature ON
Frost protection
OFF
Low batteries
Note: When the programmable thermostat is in Stand-by, press to start the backlight. Now it can be set.

Installation
Set heating / cooling
Set comfort / reduction temperature
Function Off
Lock setting
Temperature setting
External probe setting
Boiler deadlock
Reset
Supply battery replacement
Technical features
Safety warnings
5
9
10
13
15
17
19
29
33
36
37
38
39

The appliance must be installed on a wall at a height of 1,5m off the floor in a suitable position
for correctly detecting the ambient temperature. It must not be installed in niches, behind doors
and curtains or in areas affected by sources of heat or atmospheric factors. It must be installed on
a wall or on 2 and 3 module back boxes, in dry places.
To install the programmable thermostat it is necessary:
Unhook the base from the thermostat.
Fix the base to the wall.
Connect the load to the terminals following the wiring diagram.
Connect the external temperature probe.
Hook the base to the wall.
Fit. n.2 the batteries Alkaline AA of 1,5 V in the compartment, ensuring that the polarities are
corred as indicates.
IMPORTANT: Fitting the batteries with the wrong polarity may damage the programmable
thermostat. After inserting the batteries correctly, (or after the reset) the device performs
a control cycle turning on all the display segments seconds, and after it goes into
stand-by.
Fig.1B
fig.1
o Fig.2B
INSTALLATION
05

Pressing the other active keys appear.
06

WIRING DIAGRAM
07
NO
NO
RELAY
RELAY

ASSEMBLY
1
Fig.3A
Fig.2A
Fig.4A Fig.5A
Fig.1A
Press
lift

Heating program:
Reduction temperature
Comfort temperature
Cooling Program:
Reduction temperature a 28° C
Comfort temperature a 24° C
Frost protection +5°C settable, active only in heating mode
FACTORY SETTING
09
2.0

The thermostat can regulate system of:
3.1 HEATING
3.2 COOLING
3.1 HEATING
3.1.1 Start the display by pressing
3.1.2 Press
3.1.3 Press up to position on that it will start to flash.
3.1.4 Press OK to confirm. The display shows ON and . If it’s not confirmed after 10 seconds
it returns to Stand-by.
3.2 COOLING
3.2.1 Start display by pressing
3.2.2 Press
SET. HEATING / COOLING
3.0
10

10
11
3.2.3 Press up to position on that it will start to flash and OFF appears.

12
3.2.4 Press OK to confirm. The display shows On and . If it’s not confirmed after
10 seconds it returns to Stand-by.
SYSTEM ACTIVATION SIGNALING
When the icons are animated, the system is active.

You can set the Reduction or Comfort temperature in the mode of:
4.1 Heating
4.2 Cooling
You can set the temperature between +2 and + 35° C in steps of 0.1 ° C by pressing
or .
4.1 Heating
Make sure that the icon is active.
4.1.1 Press
4.1.2 Press
4.1.3 Press up to position / that it will start to flash.
SET COMFORT / REDUCTION TEMPERATURE
4.0
13

14
4.1.4 Press OK.
Fig.8
Fig.9
Fig.9

4.1.5 Press or to set the desired Reduction or Comfort value .
If it’s not continued after 10 seconds it returns to Stand-by.
4.1.6 Press OK to det the desired temperature.
4.2 Cooling
Make sure that the symbol is active.
4.2.1 to set, repeat the steps 4.1.1 a 4.1.6.
5.1 Press for 4 seconds to switch-off thermostat. Now the FUNCTION OFF is activated.
It can be activated with and without Fros Protection. It is important to avoid damage caused
by low temperatures,
shows that the system is OFF with Frost Protection function active.
shows that the system is OFF with Frost Protection function disabled, shown from
icon . To set it, follow the chapter 10.
FUNCTION OFF
5.0
15

4.1.5 Press or to set the desired Reduction or Comfort value .
If it’s not continued after 10 seconds it returns to Stand-by.
4.1.6 Press OK to det the desired temperature.
4.2 Cooling
Make sure that the symbol is active.
4.2.1 to set, repeat the steps 4.1.1 a 4.1.6.
5.1 Press for 4 seconds to switch-off thermostat. Now the FUNCTION OFF is activated.
It can be activated with and without Fros Protection. It is important to avoid damage caused
by low temperatures,
shows that the system is OFF with Frost Protection function active.
shows that the system is OFF with Frost Protection function disabled, shown from
icon . To set it, follow the chapter 10.
FUNCTION OFF
5.0
16

5.2 Press for 4 seconds to switch-on the thermostat. The display shows ON for
3 seconds.
17
Fig.10
Fig.11
Fig.12
Fig.12

The thermostat is provided with a 3 digit Lock Code.
This function locks the display to avoid accidental changes to the settings caused by
unintentionelly touching the screen:
6.1 Start display by pressing
6.2 Press and hold simultaneously for 4 seconds and up to position on
6.3 After 3 seconds, the first digit on the left will flash so press or to set it.
LOCK SETTING
6.0
18
Fig.13