tedee BleBox smart User manual

Installation and Tedee integration manual
BleBox smart
relay module

Cloud connection
BleBox smart relay module is an additional accessory for your existing relay controller. The
module is designed to secure your electronic door lock, garage gate, parking barrier, or any other
devices that are unlocked with an electric signal.
Adding a BleBox smart relay module to your setup lets you control your devices from anywhere
using our designated Tedee app.
Be aware that this module is not a relay controller; they are two separate devices.
BleBox smart relay module is wire-connected to a relay controller. It can also be accessed by a
local Wi-Fi network and the internet to integrate with an online cloud platform. This allows you
to have a remote and wireless smartphone control for your device – no matter the distance or
location.
Be aware that the BleBox smart relay module can only work if your smartphone is connected to
the internet. The cloud connection requires permanent access to the module over the internet..
If your relay module cannot connect to a Wi-Fi network, then installing an additional mobile
data Wi-Fi router (which may involve a monthly fee) is necessary.
Please note that short-distance Bluetooth or direct Wi-Fi connections are unavailable for
local device control.
Furthermore, activating BleBox smart relay module also requires an internet connection in
your smartphone. Be aware that if you are installing the relay controller for devices in locations
without an internet connection, such as underground garages or closed corridors, you’ll have to
nd an internet connection to control it.
In addition, an electric push button can be connected to the module.
Preparation for installation
Compatibility
Setting up a BleBox smart relay module requires some technical knowledge. Follow the steps
below to ensure the module is compatible with your hardware device.
Both DC and AC power the BleBox smart relay module with a voltage range of 12-24V. It
supports relay openers supplied with 230V and up to 5A current.

Installation tutorial
Relay controller’s location and approval for alteration
Wi-Fi ranges
The installation process of the BleBox smart relay module involves an electronic connection,
to connect it with the online cloud service, and then integrate the systems with the Tedee
application. Simply follow the steps below.
BleBox smart relay module should be installed by qualied installers or electricians only.
Warning
Connect only following the diagram presented in this manual. Improper connections may
be dangerous, damaging to the relay controller, and impact your warranty.
Danger! Risk of electric shock! Even with the device turned off, the outputs may still be
live. All assembly work should ALWAYS be performed with the disconnected power
circuit.
Connecting the device to a power supply that does not meet the quality requirements
specied in EN 50081-1, EN 50082-1, UL508, and EN 60950 will impact the warranty.
The module is installed inside the relay controller, which may be far from the device you wish
to control. For example, the relay controller for a property’s fence gate may be installed in the
garage, etc. The relay module is not installed directly at the gate, intercom, or on a door lock.
It may be necessary to ask your building’s administration or maintenance for its placement and/or
approval for shared hardware modication.
After determining the relay controller’s location, you must conrm that there is permanent
internet access in this spot and that the connection to the Wi-Fi network works correctly.
The data transfer to and from the module and between the Wi-Fi is minimal, so the connection
does not require a specic transfer speed. However, ensure the relay module has a steady
connection to an accessible wireless network and that you have its password or can access its
conguration.
Preparation
Disconnect the installation supply voltage before installing the module. Switch off the main fuse
or disconnect the power cord from the main socket.
The module should be installed in a place protected against adverse environmental conditions
and third-party access, for example, in the ush box or inside the enclosure of the controlled
device.
Normally Open (NO) and Normally Closed (NC) mechanisms are compatible with the module. NO
is set as default in the advanced settings of the controller (in the wBox app).

Connection
Start by connecting the +12V or +24V power to the [12-24 AC/DC] inputs (3) & (4) as shown on
the drawings above.
Connect the electric bolt lock or the electromagnetic lock circuit to the relay output circuit –
connectors (1) & (2).
The NO output is normally open, which means it does not conduct in the rest state, while the
NC output is normally closed, which means it conducts in the rest state. You can set up the NO
(default) or NC feature in the module settings over the wBox app (in the “Advanced settings”
section) while you are connected directly to the module’s Wi-Fi.
It is possible to receive feedback from the controller, which indicates the positions ‘closed’ or’
intermediate position’. To do this, connect the circuit of the electromechanical limit switch with
the input IN1 of the controller, as shown on the drawings: connectors (3) & (5). Please note that
the polarization of the limit switch inputs does not matter.
It is also possible to connect a digital inductive proximity sensor. This sensor must be powered by
Remember, the metallic elements (wires, housing parts) may negatively inuence the wireless
connection of the device and its work. It’s recommended that the module is xed in a steady
position.
Read the diagrams below, then proceed to install the relay module. Pay particular attention to the
designation of the relay module connectors.
1
1
2
2
3
3
4
4
5
5
6
6
7
7

the same input you connect the controller to, and the sensor output should be connected to the
input IN1 – connector (5).
To unlock the relay with the optional monostable switch (push-button), connect the switch circuit
to the IN2 – connector (6) and COM input of the controller – connector (3). This switch is normally
used as an exit button for a building or property.
Ensure the device is connected properly according to the diagram and there are no metal
components which may accidentally short-circuit.
Now, start the device by turning on the power and turning on the main fuse or connecting the
power cord to the power outlet.
Prepare the wBox app
Download and install a wBox by blebox.eu mobile app, available in Google Play and App Store.
App Store Google Play
Launch the app and
create a login to
access your wBox
account. Create a new
account or log in with
Google or Facebook.
If you’re a professional
installer, ensure your
client can access this
account for future use
and conguration.
Conguring device

Begin adding a new device
Connect to the relay module
Start adding a new device by tapping a “+” icon in the top-right corner of the screen.
Select “Add new device.”
Choose “Add and set up a new device.”
Make sure that your relay module is powered.
Turn ‘data transfer’ on your smartphone off.
Enable the Wi-Fi network on your smartphone and search for ‘Wi-Fi devices’.
Connect to the Wi-Fi network called “Doorbox - <YourDeviceID>”. <YourDeviceID> will be a
set number representing your device’s serial number.
DoorBox

Add the device to your account
Connect to your local Wi-Fi
Return to your wBox app. Close the integration tutorial window by pressing “X” in the top-left
corner.
Your app’s home window will show a message stating that you have connected to a new device
and can add it to your account. Press “Add device to account.”
Press “Control this device” under your device’s name.
Press the “Settings” icon in the top-right corner of the screen.
In the device’s settings windows, press “Connection”.
Choose your local Wi-Fi network at the bottom of the screen and log in with your Wi-Fi
password.
DoorBox
DoorBox
yourWiFi
yourWiFi
DoorBox
DoorBox
DoorBox
DoorBox

Congure
Integration
You can go to “Device settings” in the settings screen above to access additional conguration
options.
Here you can tailor the module’s operation to your Normally Open (NO) or Normally Closed
(NC) mechanisms.
You may also adjust the impulse duration from 0.1 to 300 seconds.
Changing these settings is available only when your smartphone and the relay module are
connected to the same local Wi-Fi network.
Now, you are about to integrate your wBox and Tedee accounts. This is done only once, no matter
how many relay modules you add to your wBox account. Any relay module will integrate with the
Tedee app.
Launch your Tedee app and log in to your Tedee account. If you still need to become a user, create a
Tedee account.
Click the Menu icon in the upper left corner and choose “Settings”, then “Integrations”, and “BleBox.”
Press “Connect” and log in with your wBox app account details. When asked to authorize
Tedee to your wBox account, press “Authorize”.
Now you can see the integrations “Connected” status. The relay module has been added to the
list of your devices in the Tedee app.
If your Relay Module is not readily added to your devices list, access this integration setting and
press “Sync” to refresh.
You can now control your relay with the Tedee app.

Protect the device’s Wi-Fi network
This step is crucial for secure control over the device for authorized persons only.
Without it, any third-party individual can access its conguration.
Tap the centre button to open the connected relay device.
You can tap the button again to prolong the activation time during the opening. This way, the
gate or door will be unlocked longer.
At the bottom of the screen, you can go to the “Access sharing”, “Activity logs”, or “Settings”
tabs to access additional features. Go to https://tedee.com for more information on how to
use smart access features.
How to control your relay with the Tedee app
Press on a relay module to access its control screen.

If you want to refresh the module’s setup and install it with another hardware, you may want to
reset your device using the “factory reset” option.
Be aware that this process removes all device congurations (it does not change the device
owner, though). If you use the “Factory reset” button, the module must be integrated again by
following the steps in this manual.
The reset is indicated manually by connecting the module to an analogue monostable button
and following a sequence of presses.
Prepare a timer or use the watch to keep track of the sequence of steps.
Factory reset
Connect a button
The reset is indicated manually by connecting the module to an analogue monostable button.
Before manipulating the installation wires, turn the system’s power off.
Plug the push-button to IN1 and COM: inputs (3) & (5)
If you already use a monostable push-button in your setup, please, reconnect it from IN2 to the
IN1 port.
To prevent the access of unauthorized persons to your relay module, you must set up a password
to protect to protect the device’s Wi-Fi network.
Return to the wBox app to the device settings page and choose “Service connection (AP)”.
Click “Add password protection” bar.
Enter the password and press “Save” in the upper right corner.v

Follow the reset sequence
1. Before turning the power back on, follow the reset sequence and keep track of the buttons
you use. Start the sequence no more than 30 seconds after turning the power back on. If
you don’t start the sequence in this period, turn the power off and back on again.
2. Press and hold the button for 10s seconds. Then release.
3. Click the button ve times – press and release it rapidly. All ve clicks should be executed in
no more than 10 seconds
4. Press and hold the button for 10 seconds again. Then release.
5. Wait 10 seconds. During this time, the module reboots and turns back on in the factory
settings.
Return to the previous setup
After the factory reset, you may want to replug the monostable button to its primary setup or
remove it altogether.
Turn the system’s power off.
Replug the button from the IN1 to the IN2 port
or
unscrew the button wires and remove them.
Plug the push-button back into the IN2 port.
Turn the power back on.
Finally, the module will maintain the new factory conguration settings, and you can pair it
with your other apps and devices.