Teknion complements CEREBRO Operating and maintenance instructions

Section:
Date: May 2019
CEREBRO, ELECTRICS FOR IC
complements
Installation Guides
Rev.00
Page: 1 of 10
COM_602
10
9
8
7
5
4
3
1
12
NOTE: To optimize Cerebro assets,
refer to Teknion Navigate User Guide.
Swerv Integrated Cerebro Assembly (YMSZ)

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 2 of 10
COM_602
ITEM
NO.
PREVIEW DESCRIPTION
PART
NUMBER
QTY.
1
SWERV IC
ACTUATOR
KIT
N09-
9181 1
ITEM
NO.
PREVIEW DESCRIPTION
PART
NUMBER
QTY.
2
MOTOR
CABLE PVC
FREE, 500MM
N09-
8402\05
1
3
CEREBRO
GROMMET
B02-0769 1
Part & Product Identification

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 3 of 10
COM_602a
ITEM
NO.
PREVIEW DESCRIPTION PART NUMBER QTY.
4
CEREBRO
BASE
CASTING
ASSEMBLY
N09-8612 1
5
SWERV BASE
COVER
B02-0697 1
6. SWERV IC HARDWARE KIT (X05-0500)
6.1
M5 X 0.8,
50MM SHCS
E01-1285 4
6.2
SCRW 1/4-
20X5/8 ZNC
PN QD MCHN
(690150)
E01-0992 2
ITEM
NO.
PREVIEW DESCRIPTION PART NUMBER QTY.
7
SWERV IC
STATIC ARM
CASTING
A25-0650 1
8
M8 X 1.25,
25mm LOW
HEAD SHCS
E01-1312 1
9
SWERV WIRE
COVER
B02-0700 1
10
SWERV
DYNAMIC
SUB-
ASSEMBLY
N09-7697 1
12
SWERV VESA
PLATE
B02-0708 1
13
SWERV VESA
SCREW
D06-4266 4
ITEM
NO.
PREVIEW DESCRIPTION PART NUMBER QTY.
11
SWERV VESA
PLATE
B02-0708 1
12
SWERV VESA
SCREW
D06-4266 4
2.1.3
CEREBRO
FOAM
ACTUATOR
RESTRAINT
B02-0767 1
2.1.4
CEREBRO
CLAMP
PLATE
ASSEMBLY
N09-8706 1
2.1.4.1
CEREBRO
CLAMP
PLATE
A16-7378 1
2.1.5
MOTOR
CABLE PVC
FREE, 500MM
N09-8402\05 1
2.2
CEREBRO
GROMMET
B02-0769 1
Part & Product Identification

Section:
Date:May 2019
CEREBRO
complements
Installation Guides
Page: 4 of 10
COM_602
1
6.2
3
SECURE CEREBRO ACTUATOR KIT
STEP 1: Place the Actuator underneath the worksurface using the screws provided. STEP 2: Before placing grommet cap, run large wires through the grommet hole. Then, place
grommet cap.
PLACE LARGE CABLES AND GROMMET

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 5 of 10
COM_602
6.1
4
1
5
4
SECURE BASE CASTING
STEP 4: Using screws provided, secure the Base Casting into place. STEP 5: Place Casting Cover over top of the Base Casting.
PLACE CASTING COVER

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 6 of 10
COM_602
8
7
5
7
10
7
ASSEMBLE SWERV IC STATIC ARM CASTING
STEP 6: Using the screw, secure the Swerv IC Static Arm Casting. Tighten the screw with
the allen key.
STEP 7: Connect the Dynamic Arm Assembly to the arm casting.
SECURE DYNAMIC ARM ASSEMBLY

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 7 of 10
COM_602
107
12
13
12
INSTALL VESA PLATE
STEP 8: Fasten VESA Plate onto Monitor. STEP 9: Mount Monitor on the Swerv Arm.
MOUNT MONITORS

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 8 of 10
COM_602
ADJUST ARM
NOTE: Adjust arm so that monitor floats at all heights. Increase (+) lift strength by turning
the allen key counter clockwise if monitor does not stay up when raised.
NOTE: Adjust arm so that monitor floats at all heights. Decrease (-) lift strength by turning
the allen key clockwise if monitor does not stay down when lowered.
ADJUST ARM

Section:
Date: May 2019
CEREBRO
complements
Installation Guides
Page: 9 of 10
COM_602
9
7
FINE ADJUSTING ARM
NOTE: For more detailed balancing, tighten bottom screw in 1/2 turn increments to provide
a specific balance.
STEP 8: Install display and power cable as shown above. Run Display Cords through Static
Arm and secure Wire Cover by sliding the cover into place.
INSTALL WIRE AND WIRE MANAGEMENT

Section:
Date: May 2019
complements
Installation Guides
Page: 10 of 10
COM_602
Channel 4
Channel 3
NOTE: Connect table legs to channels
1 & 4 and leave channel 3 for the
monitor arm actuator. Refer to Teknion
Navigate User Guide for details.
6
PLEASE MAKE SURE THE WORKSURFACE IS HIDDEN IN ALL OF THESE VIEWS
NOTE: Connect the cables to the control box by connecting the Monitor Arms (YMSZ) to Channel 3 and connecting the remaining cables for YCH to the appropriate Channels (1 & 4) as shown
above. The channels are identified by moulded in numbers on the control box housing. For more information, refer to the programming sequence guide.
CABLE MANAGEMENT & PROGRAMMING FOR CEREBRO