TELECO AUTOMATION GSM900 User manual

1
DOC.: T625.01
PRODUCT: GSM900 DATE: 08/08/14
GSM900: Plug-in GSM module for remote control of doors, to be installed into TVPRP868x10x control unit.
The device has a built-in GSM-Quad Band module, suitable for communication via SMS or phone-call.
For a correct installation and use of this product, scrupulously respect the indications laid out in this manual.
The product could produce or be subject to interferences that may inuence its performance or the functioning
of other devices in the proximity. Read carefully the Safety Information.
TELECO AUTOMATION SRL - Via dell’Artigianato, 16 - 31014 Colle Umberto (TV) ITALY
TELEPHONE: ++39.0438.388511 FAX: ++39.0438.388536 - www.telecoautomation.com
This document is the property of Teleco Automation Srl who reserves all reproduction and copying rights
EN - PLUG-IN GSM MODULE FOR REMOTE CONTROL OF DOORS
1- Product description
3- Installation
•Insert the SIM in the proper slot of GSM900.
•Install the aerial for the GSM signal reception.
•Plug the module in the proper connector of TVPRP control unit.
•Switch the TVPRP on.
•Wait about 30 seconds for the initial startup and the connection to GSM signal.
Connection led quickly ashes during the GSM signal research, then slower once the connection is ready.
GSM led shows the quality of the connection and possible errors:
Programming button
Connection led
PROG led GSM aerial
Terminal
GSM led
2- Preliminary check
•SIM card must be active and having credit.
•PIN code and the answering service MUST be disabled.
•Do not activate any other additional services, like the incoming calls lter or number masking.
We suggest to try the correct functioning of the SIM by means of a standard mobile phone before starting the
installation of the product.
GSM led Meaning
Quick ash Startup of the module (about 30 sec. at the rst power-on)
ON (solid) No GSM signal
4 slow ashes and a pause Excellent GSM signal
3 slow ashes and a pause Good GSM signal
2 slow ashes and a pause Sufcient GSM signal
1 ash and a pause Poor GSM signal
4 quick ashes then ON (solid) No SIM card
Slow ashing SIM card has the PIN code activated
www.garagedoorsonline.co.uk
01926 463888

2
DOC.: T625.01
PRODUCT: GSM900 DATE: 08/08/14
If the door is totally closed, the phone
call activates an OPENING
• If the door is moving, the phone call activates a STOP.
• If the door is partially open the phone call activate the
opposite command of the previously executed command.
4- COMMANDS BY PHONE CALL
By means of a free phone call, it’s possible to activate an opening or a closure of the door.
In order to use this function it is necessary to enable the telephone number in the GSM module.
If the door is totally open, the phone call
activates a CLOSURE
5- Enabling/disabling a telephone number to the function CALL
1. Press once the programming
button, PROG led ashes then it
turns ON.
2. Within 30 seconds make a call;
when the GSM module receives the
call PROG led quickly ashes.
3. Hang-up.
within 30 sec.
PROG
led
Enabling a number
1. Press twice the programming
button, PROG led slowly ashes.
2. Within 30 seconds make a call
from the number to disable; when
the GSM module receives the call
PROG led turns on.
3. Hang-up.
5.1- Disabling ALL the telephone numbers
10 sec.
within 30 sec.
...
Disabling a number
Press 3 times and hold the programming button down for at least 10 seconds; during this lapse PROG led will ash
intermittently and quickly, until it will turn constantly on. At the end release the button.
Note: It is possible enabling/disabling a telephone number even with SMS commands.
...
...
PROG
led
PROG
led
www.garagedoorsonline.co.uk
01926 463888

3
DOC.: T625.01
PRODUCT: GSM900 DATE: 08/08/14
# DESCRIPTION SMS TEXT
1
CHANGE THE PASSWORD
Syntax: xxxxx is the new password.
The command PWD is followed by the valid password.
Only numeric passwords are permitted, 5 digits long.
PWDpassword,xxxxx,xxxxx
2
MEMORIZE A NUMBER IN THE TELEPHONE BOOK
Syntax: x = position in the telephone book (1-8).
y = telephone number (max. 19 digits).
Notes: the telephone book has 8 positions maximum.
The numbers memorized in the telephone book have both
alarm calls and SMS activated by default.
If a position is already occupied, it is overwritten.
TELx,yyyyyyyyyyyy
3DELETE A NUMBER IN THE TELEPHONE BOOK
Syntax: x = position in the telephone book to delete (1-8).
DELx,password
4LIST OF NUMBERS IN THE TELEPHONE BOOK
The device sends the list of the numbers with their position.
NUM?,password
5
TOTAL RESET OF THE PARAMETERS AND DELETION OF
ALL THE MEMORIZED NUMBERS
It completely deletes the memory, restoring the factory settings.
RESETpassword
6
ACTIVATION OF ALARM SMS FOR A SPECIFIC NUMBER
Syntax: the command SMS is followed by the positions in the
telephone book (from 1 to 8 max.) of the numbers for which
is required to activate the function (e.g., SMS145 activate the
sms sending for the numbers at positions 1,4 and 5). This function
sends only alarm sms, like “Alarm door” and “Low battery”.
Note: All the numbers memorized by means of the command
TELx have this function activated by default.
SMSxxxxxxxx
7
DEACTIVATION OF ALARM SMS FOR A SPECIFIC NUMBER
The command deactivates the reception of alarm sms.
See syntax and notes above.
DSMSxxxxxxxx
By means of a SMS it’s possible to command the door, check its status, activate some functions or modify
system parameters. The default password is “12345”, but it can be modied with an SMS.
Notes:
•Once the password is modied, if forgotten, it’s not possible any restoring of the default one.
• SMS commands are NOT case sensitive.
• If any SMS not reported in the table below is received (e.g., credit info), the device forward the same
SMS to the rst number memorized in the telephone book.
•According to the standard used in a specic country, it could be necessary write the telephone numbers
with the international dialing codes or just with a “0” before.
•The device replies to the conguration SMS with another SMS and a phone call.
Automatic SMS:
The module automatically sends two types of alarm messages to the rst number in the telephone book.
1- SMS “ALARM DOOR”: this message is sent to the numbers memorized in the telephone book when
TVPRP control unit has received a signal from an alarm transmitter (e.g., TVTCTM or TVSSH).
2- SMS “BATTERY LOW”: this message is sent to the numbers memorized in the telephone book when
TVPRP control unit has received a signal “battery low” from wireless sensitive edge transmitter TCSP240.
In the next table there’s the complete list of all the available SMS commands with the relative description:
6- SMS COMMANDS
www.garagedoorsonline.co.uk
01926 463888

4
DOC.: T625.01
PRODUCT: GSM900 DATE: 08/08/14
# DESCRIPTION SMS COMMAND
8
ACTIVATION OF ALARM CALLS FOR A SPECIFIC NUMBER
Syntax: the command VOC is followed by the positions in the
telephone book (from 1 to 8 max.) of the numbers for which
is required to activate the function (e.g., VOC145 activate the
alarm calls for the numbers at positions 1,4 and 5). This function
make only alarm calls in case of “Alarm door” and “Low battery”.
Note: All the numbers memorized by means of the command
TELx have this function activated by default.
VOCxxxxxxxx
9
DEACTIVATION OF ALARM CALLS FOR A SPECIFIC NUMBER
The command deactivates the reception of alarm calls.
See syntax and notes above.
DVOCxxxxxxxx
10 REQUEST OF DOOR STATUS
Reply: DOOR OPEN - DOOR CLOSED
DOOR?
11
REQUEST OF SYSTEM ERRORS
Reply:
Photocell: OK/error
Wired safety edge: OK/error
Wireless safety edge: OK/error
STOP button: OK/error
ERRDOOR
12
MEMORIZING A PHONE NUMBER FOR DOOR COMMAND
Syntax: it’s possible to memorize one number (e.g.,
MAC12345,xxxxxxxxxxxx) or more (maximum 10), separated
by commas, for each SMS.
Furthermore it’s possible to memorize one number (or more)
that will be valid just for a limited number of commands: in
order to activate this function add to the number the parameter
“U”, followed by the validity (number of commands).
(es. MACpassword,xxxxxxxxxxxUyyy = valid for yyy commands)
MACpassword,xxxxxxxxxxxx,
xxxxxxxxxxxx,.........
MACpassword,xxxxxxxxxxxx,
xxxxxxxxxxxxUyyy,.........
13
DELETING A PHONE NUMBER FOR DOOR COMMAND
Syntax: it’s possible to delete one number (e.g.,
MAC12345,xxxxxxxxxxxx) or more (max. 10), separated by
commas, for each SMS.
DACpassword,xxxxxxxxxxxx,
xxxxxxxxxxxx,.........
14
DELETING ALL THE NUMBERS FOR DOOR COMMAND
Syntax: the command DAC must be followed by the valid
password, repeated three times.
DACpassword,password,
password
15 OPEN DOOR COMMAND OPENpassword
16
CLOSE DOOR COMMAND
Note: this command has no effect if the system is congured in
hold-to-run mode.
CLOSEpassword
17 REQUEST OF DOOR CYCLES DOOR CYCLE
18 GSM CONNECTION CHECK
Reply: OK
CKE
19
ACTIVATION OF FEEDBACK CALLS AFTER EACH SMS
After every command sent via SMS, the device make a call
and send an SMS as conrmation of the correct reception. This
automatic call must be manually stopped, hanging-up.
The function is deactivated by default.
ACALL
20 DEACTIVATION OF FEEDBACK CALL AFTER A SMS DCALL
www.garagedoorsonline.co.uk
01926 463888

5
DOC.: T625.01
PRODUCT: GSM900 DATE: 08/08/14
# DESCRIPTION SMS COMMAND
21
ACTIVATION OF “SURVIVAL” SMS (from ver. 1.7 on)
Syntax: the command is followed by the frequency of sending
(days, from 1 to 250). E.g., SMSON15: the device will send a
sms “OK” every 15 days, in order to keep the SIM active.
SMSON,xxx
22 DEACTIVATION OF “SURVIVAL” SMS (from ver. 1.7 on) SMSOFF
7- TECHNICAL SPECIFICATION
The product complies to the following standards:
Art. 3.1(a) Safety EN 60950-1
Art. 3.1 (a) Health Council Rec. 99/519/EC
Art. 3.1(b) EMC EN 301 489
Art. 3.2 Radio EN 301 511
The Declaration of Conformity (DoC) is available at the page www.telecoautomation.com/ce
- Power supply 12Vdc (provided by control unit TVPRP)
- Operating temperature range -20 / +50 (°C)
- Telephonic module SIM900 QBand
- SIM type Standard
7.1- SAFETY INFORMATION
WARNINGS:
The functioning of the device next to radio, televisions, mobile phones or any other electronic devices,
could generate interference. The device can be subject to external interferences, which can inuence
its proper functioning.
Do not install the device next to pacemakers or any other electronic medical devices, because it
could interfere with the correct functioning of these devices.
We inform that GSM900 works using radio frequency and not one telephonic company can guarantee
the connection to the device at any moment. For this reason the product cannot be used with personal
emergency systems.
Furthermore the user is totally and exclusively responsible of the remote command of the door by
means of the product GSM900. Teleco Automation Srl declines any responsibility for direct or indirect
damages caused by possible malfunctioning, wrong installation or external causes like power supply
black-out or GSM signal missing.
Notes:
- A telephone number cannot be memorized more than one time.
- In order to delete a telephone number by means of the command “DACpassword,xxxxxxxx”, it is
necessary to write it with the same dialing code earlier used for the command “MAC12345,xxxxxx”.
In the view of a constant development of their products, the manufacturer reserves the right for
changing technical data and features without prior notice.
© Copyright 2014 TELECO AUTOMATION Srl (ITALY). All rights reserved.
www.garagedoorsonline.co.uk
01926 463888