WAGO 750-1504 User manual

Pos: 2 /Dokumentatio n allgemein/Einband/Ei nband Deckblatt @ 9\mod_12 85229289866_0.doc @ 64941 @ @ 1
Manual
WAGO-I/O-SYSTEM 750
16DO 24V DC 0.5A
750-1504
16-Channel Digital Output Module 24 V DC, High-side
switching
Version 1.0.1
Pos: 3 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Impressum - allgemein e Angaben, Anschri ften, Telefonnummern un d E-Mail-Adressen @ 3\mo d_1219151118203_21.doc @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
Manual
Version 1.0.1
© 2012 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Liste für Textmarke Einband_vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-1504 16DO 24V DC 0.5A
Po
s: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhaltsverzei chnis - ohne Gliederung - und Verzeichnis @ 3\mod_121915 1230875_21.doc @ 21063 @ @ 1
Table of Contents
1Notes about this Documentation................................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright................................................................................................... 5
1.3 Symbols..................................................................................................... 6
1.4 Number Notation....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2Important Notes........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject to Changes............................................................................... 9
2.1.2 Personnel Qualifications....................................................................... 9
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions...... 9
2.1.4 Technical Condition of Specified Devices......................................... 10
2.2 Safety Advice (Precautions).................................................................... 11
3Device Description ..................................................................................... 13
3.1 View........................................................................................................ 15
3.2 Connectors............................................................................................... 16
3.2.1 Data Contacts/Internal Bus................................................................. 16
3.2.2 Power Contacts/Field Supply............................................................. 17
3.2.3 CAGE CLAMP®Connections ........................................................... 18
3.3 Display Elements .................................................................................... 19
3.4 Operating Elements................................................................................. 19
3.5 Schematic Diagram................................................................................. 20
3.6 Technical Data ........................................................................................ 21
3.6.1 Device data......................................................................................... 21
3.6.2 Communication .................................................................................. 21
3.6.3 Supply................................................................................................. 21
3.6.4 Outputs ............................................................................................... 21
3.6.5 Wire Connection................................................................................. 22
3.7 Approvals................................................................................................ 23
3.8 Standards and Guidelines........................................................................ 23
4Assembly..................................................................................................... 24
4.1 Assembly Sequence ................................................................................ 24
4.2 Inserting and Removing Devices............................................................ 25
4.2.1 Inserting I/O Module.......................................................................... 25
4.2.2 Removing the I/O Module.................................................................. 26
5Connect Devices ......................................................................................... 27
5.1 Connecting a conductor to the CAGE CLAMP® S................................. 27
6Process Image............................................................................................. 28
7Using Interference-Free IO Modules in Safety Related Applications... 29
7.1 Important Notes....................................................................................... 30
7.2 Connecting the IO Module to Safety Switching Devices or Safety
Modules................................................................................................... 31
7.2.1 General Structure of a Potential Group.............................................. 31
Manual
Version 1.0.1

4 Table of Contents WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
Manual
Version 1.0.1
7.2.2 Examples of Connection..................................................................... 32
List of Figures...................................................................................................... 33
List of Tables........................................................................................................ 34
=== Ende der Liste für Textmarke Verzeichnis_ vorne ===

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-1504 16DO 24V DC 0.5A
Po
s: 7 /Alle Serien (Allge meine Module)/Über schriften für alle Seri en/Hinweise zur Dokume ntation - Überschr ift 1 @ 4\mod_1237987661750_21. doc @ 29029 @ 1 @ 1
1 Notes about this Documentation
Po
s: 8 /Alle Serien (Allge meine Module)/Hin weise zur Dokumentation/ Hinweis: Dokumentati on aufbewahren @ 4\mod_1 237987339812_21. doc @ 29026 @ @ 1
Keep this documentation!
The operating instructions are part of the product and shall be kept for the entire
lifetime of the device. They shall be transferred to each subsequent owner or user
of the device. Care must also be taken to ensure that any supplement to these
instructions are included, if applicable.
s: 9 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise z ur Dokumentation/Gül tigkeitsbereic h Dokumentation Buskle mme75 0-xxxx, ohne Varianten angabe @ 4\mod_1237986650 812_21.doc @ 29020 @ 2 @ 1Po
1.1 Validity of this Documentation
This documentation is only applicable to the I/O module 750-1504
(16DO 24V DC 0.5A) of the WAGO-I/O-SYSTEM 750 series.
Po
s: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweis e zur Dokumentation/ Hinweise/Achtung: Hin weis zur Dokumentati on Busklemmen 750-xxxx @ 4\ mod_1237986979656_21.doc @ 29023 @ @ 1
The I/O module 750-1504 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
s: 11.1 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Urheberschutz au sführlich @ 4\mod_1235 565145234_21.doc @ 27691 @ 2 @ 1Po
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Po
s: 11.2 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
s: 11.3 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Symbole @ 3\mod_121 7394197593_21.doc @ 21010 @ 2 @ 1Po
1.3 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-1504 16DO 24V DC 0.5A
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
s: 11.4 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1Po
Manual
Version 1.0.1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
s: 11.5 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Zahlensyste me@ 3\ mod_1221059454015_21. doc @ 21711 @ 2 @ 1Po
1.4 Number Notation
Table 1: Number Notation
Number code Example Note
Decimal 100 Normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100' In quotation marks, nibble separated with dots (.)
Po
s: 11.6 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentati on/Schriftkonven tionen @ 3\mod_122105952 1437_21.doc @ 21714 @ 2 @ 1
1.5 Font Conventions
Table 2: Font Conventions
Font type Indicates
italic Names of paths and data files are marked in italic-type.
e.g.: C:\Programme\WAGO-I/O-CHECK
Menu Menu items are marked in bold letters.
e.g.: Save
> A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value” Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button] Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key] Keys are marked with bold letters in square brackets.
e.g.: [F5]
Po
s: 12 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Important Notes 9
750-1504 16DO 24V DC 0.5A
s: 13 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Wichtige Erläu terungen - Überschrif t 1 @ 4\mod_1241428899156_2 1.doc @ 32170 @ 1 @ 1Po
2 Important Notes
Po
s: 14.1 /Alle Serien (A llgemeine Module)/W ichtige Erläuterungen/ Einleitung Wi chtige Erläuterungen @ 3\mod_12 21059818031_21.doc @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Po
s: 14.2 /Alle Serien (A llgemeine Module)/Ü berschriften für alleS erien/Rechtlic he Grundlagen - Überschri ft 2 @ 3\mod_1221060626343 _21.doc @ 21726 @ 2 @ 1
2.1 Legal Bases
Po
s: 14.3 /Alle Serien (A llgemeine Module)/W ichtige Erläuterungen/ Änderungsvorbeha lt @ 3\mod_1221060036484 _21.doc @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Po
s: 14.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Per sonalqualifikati on 750-xxxx @ 3\mod_122 4061208046_21.doc @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on Series 750 devices may only be carried out by
electrical specialists with sufficient knowledge in automation. The specialists
must be familiar with the current norms and guidelines for the devices and
automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Po
s: 14.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Bes timmungsgemäße Verwendu ng 750-xxxx @ 3\mod_1 224064151234_21.doc @ 24070 @ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to the actuators or higher-level control systems. Using programmable controllers,
the signals can also be (pre-)processed.
The components have been developed for use in an environment that meets the
IP20 protection class criteria. Protection against finger injury and solid impurities
up to 12.5 mm diameter is assured; protection against water damage is not
ensured. Unless otherwise specified, operation of the components in wet and
dusty environments is prohibited.
Operating 750 Series components in home applications without further measures
is only permitted if they meet the emission limits (emissions of interference)
according to EN 61000-6-3. You will find the relevant information in the section
on "WAGO-I/O-SYSTEM 750" "System Description" "Technical Data" in
the manual for the used fieldbus coupler/controller.
Manual
Version 1.0.1

10 Important Notes WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Po
s: 14.6 /Alle Serien (A llgemeine Module)/W ichtige Erläuterungen/ Technischer Zustan d der Geräte @ 3\mod_122106 0446109_21.doc @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The components to be supplied Ex Works, are equipped with hardware and
software configurations, which meet the individual application requirements.
WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in
case of changes in hardware or software as well as to non-compliant usage of
components.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Po
s: 14.7 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Important Notes 11
750-1504 16DO 24V DC 0.5A
s: 14.8 /Alle Serien (A llgemeine Module)/Ü berschriften für alleS erien/Sicherhei tshinweise - Überschr ift 2 @ 6\mod_1260180299987_ 21.doc @ 46724 @ 2 @ 1Po
2.2 Safety Advice (Precautions)
Po
s: 14.9 /Alle Serien (A llgemeine Module)/W ichtige Erläuterungen/ Sicherheitshin weise/Einleitung Si cherheitshinweise Hardware @ 6\mod_1260180 170493_21.doc @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Po
s: 14.10.1 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr/ Gefahr: Nicht an Geräten un ter Spannung arbeiten! @ 6\mod _1260180365327_21.doc @ 46727 @ @ 1
Do not work on components while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
s: 14.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/W ichtige Erläuterungen/ Sicherheitshin weise/Gefahr/Gefahr : Einbau 0750-xxxx nur i n Gehäusen, Schränken oder elektrischen Betri ebsräumen! @ 6\mod_12601 80556692_21.doc @ 46731 @ @ 1Po
Installation only in appropriate housings, cabinets or in electrical operation
rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
s: 14.10.3 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr/ Gefahr: Unfallverhü tungsvorschriften b eachten! @ 6\mod_126018 0657000_21.doc @ 46735 @ @ 1Po
s: 14.10.4 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Gefahr/ Gefahr: Auf normgerechte n A sc hluss achten! @ 6\mod_1260 180753479_21.doc @ 46739 @ @ 1Po
n
s: 14.11.1 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/Ac htung: Defekte oder besc hädigte Geräte austa uschen! @ 6\mod_12601808573 58_21.doc @ 46743 @ @ 1Po
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
s: 14.11.2 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/Ac htung: Geräte vor kri echenden und isolierend en Stoffen schützen! @ 6\ mod_1260181036216_21.doc @ 46747 @ @ 1Po
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
s: 14.11.3 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/Ac htung: Reinigung nur mi t zulässigen Materiali en! @ 6\mod_1260181203293_ 21.doc @ 46751 @ @ 1Po
Cleaning only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
11.4 /Alle Serien ( Allgemeine Module)/W ichtige Erläuterungen/ Sicherheitshin weise/Achtung/Achtung: Kein Kontaktspray ver wenden! @ 6\mod_1260181290 808_21.doc @ 46755 @ @ 1Pos: 14.
Manual
Version 1.0.1

12 Important Notes WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
s: 14.11.5 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/Ac htung: Verpolung ver meiden! @ 6\mod_1260184045 744_21.doc @ 46767 @ @ 1Po
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
s: 14.11.6 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei tshinweise/Achtung/Ac htung: Elektrosta tische Entladung vermeiden! @ 6\mod_1260181364729 _21.doc @ 46759 @ @ 1Po
Avoid electrostatic discharge!
The devices are equipped with electronic components that you may destroy by
electrostatic discharge when you touch. Pay attention while handling the devices
to good grounding of the environment (persons, job and packing).
s: 15 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1Po
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Device Description 13
750-1504 16DO 24V DC 0.5A
s: 16 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Gerätebeschrei bung - Überschrif t 1 @ 3\mod_1233756084656_21. doc @ 27096 @ 1 @ 1Po
3 Device Description
Po
s: 17.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/Anwendung/ DO/Anwendung 750- x5xxD O@ 3\mod_1233764594468 _21.doc @ 27120 @ @ 1
The 750-1504 Digital Output Module transmits binary control signals from the
automation device to the connected actuators (e.g., solenoid valves, contactors,
transmitters, relays or other electrical loads).
Po
s: 17.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/I/O-Beschreibung/DO/I/O-Beschreibung750-150x 16DO 1-Leiter CAGECLAMP@ 3\mod_123376462 6734_21.doc @ 27124 @ @ 1
The I/O module has 16 output channels, providing a direct connection to single-
wire actuators.
The output signals are connected to the CAGE CLAMP®connections DO 1 ... DO
16.
Po
s: 17.3 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/I/O-Beschreibung/Hinweise/Verweis auf Kapitel "Ansc hlüsse" @ 8\mod_12767753 78035_21.doc @ 57956 @ @ 1
The assignment of the connections is described in the "Connections" section.
Po
s: 17.4 /Dokumentatio n allgemein/Glieder ungselemente/- -----Leerzei le------ @ 3\mod_122466275568 7_0.doc @ 24460 @ @ 1
Po
s: 17.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/I/O-Beschreibung/Hinweise/Hinweis: DO Potentia lvervielfältigung smodule für Aktorver sorgung einsetzen @ 3\mod_1 233765481250_21.doc @ 27140 @ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the actuators.
s: 17.6 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/I/O-Beschreibung/Hinweise/Achtung: DO Induktion sspannungsbegrenz ung Elektronik @ 3\mod_123 3815757507_21.doc @ 27153 @ @ 1Po
Limit all induced voltage!
The electronic components of the I/O module can be damaged by the induced
voltage produced when inductive loads are de-activated.
An appropriate protection circuit, e.g., a recovery diode, must be installed in
parallel to the load to limit this induced voltage.
s: 17.7 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/I/O-Beschreibung/Hinweise/Achtung: DO Überlas tschutz - Einpeisek lemme mit Sicherung @ 3\mod_123 3814881117_21.doc @ 27150 @ @ 1Po
Provide for overload protection!
Overloading can damage the electronic components of the I/O module.
A fused supply module (750-601) must be installed upstream of the I/O module to
protect it against overloading!
s: 17.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/I/O-Beschreibung/DO/I/O-Beschreibung 750-x5Po
xxDO HSS / positivschaltend (24 V) @ 3\mod_12338169 55742_21.doc @ 27160 @ @ 1
The I/O module outputs provide high-side switching. If the signal status of an
output channel is at "high" the 24V potential for field power will be switched to
the appropriate output connection.
Po
s: 17.9 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/LED-Anzei ge/LED Zustand Signal @ 3\ mod_1233755258578_21. doc @ 27087 @ @ 1
A green LED indicates the switched status of each channel.
Po
s: 17.10 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Be schreibung/LED-Anzei ge/Verweis auf Kapi tel "Anzeigeelemen te" @ 5\mod_1246010525000_2 1.doc @ 36194 @ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Po
s: 17.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Be schreibung/Versor gung/Versorgung 24 V, 0 V über Leistungskontakt e Standard @ 3\mod_12264989 74531_21.doc @ 25020 @ @ 1
The I/O module receives the 24V voltage supply for the field level from an
upstream I/O module or from the fieldbus coupler/controller via the power
contacts used as blade contacts. It then provides this potential to subsequent I/O
modules via the power contacts used as spring contacts.
Po
s: 17.12 /Serie 750 (W AGO-I/O-SYSTEM)/W ichtige Erläuterungen/Si cherheitshin weise/Achtung/Achtung: Maximaler Strom Leis tungskontakte 10 A @ 3\mod_12264 99143500_21.doc @ 25029 @ @ 1
Manual
Version 1.0.1

14 Device Description WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
Do not exceed maximum current via power contacts!
The maximum current to flow through the power contacts is 10 A.
Greater currents can damage the power contacts.
When configuring the system, ensure that this current is not exceeded. If
exceeded, an additional potential feed module must be used.
s: 17.13 /Serie 750 (W AGO-I/O-SYSTEM)/W ichtige Erläuterungen/Si cherheitshinweise/ Hinweis/Hinweis: Potentialeinspei seklemme für Erde ei nsetzen! @ 3\mod_12264990374 68_21.doc @ 25023 @ @ 1Po
Use potential feed module for Ground (earth)!
The I/O module has no power contacts for PE intake and transfer. Use a potential
feed module when a PE feed is needed for the subsequent I/O modules.
s: 17.14 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Be schreibung/Versorgung/ Galvanische Trennung Feld/SystePo
m @ 3\mod_123 3756478750_21. doc @ 27102 @ @ 1
The field level and the system level are electrically isolated from one another.
Po
s: 17.15 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Be schreibung/Versor gung/Anordnung unter Berücksichtigung der Leistungskontakte be liebig @ 3\mod_1233756233 468_21.doc @ 27099 @ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node. An arrangement
in groups within the group of potentials is not necessary.
Po
s: 17.16 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Be schreibung/Einsa tzbereich/Einsatzber eich 750-xxxx alle Ko ppler/Control ler ohne Einschränkung @ 3\ mod_1232541691906_21. doc @ 26522 @ @ 1
The I/O module 750-1504 can be used with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750.
Po
s: 18 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Device Description 15
750-1504 16DO 24V DC 0.5A
s: 19 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Ansicht - Überschr ift 2 @ 4\mod_124098421734 3_21.doc @ 31958 @ 2 @ 1Po
3.1 View
Po
s: 20 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansic ht/Digitalausgangs klemmen/Ansicht 75 0-150x 16 DO CAGE CLAMP @ 3\mod_1 224766395937_21.d oc @ 24653 @ @ 1
13 14
750-15XX
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
1
6
7
5
33
5
7
2
4
Figure 1: View
Table 3: Caption acc. to figure “View”
No. Designation Description Details see chapter
1 ---
Marking possibility with
Mini-WSB ---
2 1 … 16 Status-LEDs
Outputs DO 1 … DO 16 “Device description” > “Display elements”
3 --- Data contacts “Assembly” >
“Mounting device”
4 1 … 16 CAGE CLAMP®-supplies
Outputs DO 1 … DO 16 “Device description” > “Connections”
5 --- Power jumper contacts +24 V “Device description” >
“Connections”
6 --- Release clip “Assembly” >
“Mounting device”
7 --- Power jumper contacts 0 V “Device description” >
“Connections”
Po
s: 21 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

16 Device Description WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
s: 22 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Anschlüsse - Übersc hrift 2 @ 4\mod_1240984262 656_21.doc @ 31961 @ 2 @ 1Po
3.2 Connectors
Po
s: 23 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansch lüsse/Datenkontak te/Klemmenbus - Überschr ift 3 @ 6\mod_1256294 684083_21.doc @ 43660 @ 3 @ 1
3.2.1 Data Contacts/Internal Bus
Po
s: 24.1 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Ansc hlüsse/Datenkont akte @ 3\mod_12317712591 87_21.doc @ 26002 @ @ 1
Communication between the coupler/controller and the bus modules as well as the
system supply of the bus modules is carried out via the internal bus. It is
comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data contacts
Po
s: 24.2 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Si cherheitshinweise/ Achtung/Achtung: Busklemmen nicht auf Gol dfederkontakte le gen! @ 7\mod_12663184636 36_21.doc @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
s: 24.3 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Si cherheitshinweise/ Achtung/Achtung: ESD - Auf gute Erdung der Um gebung achten! @ 7\mod_1266318 538667_21.doc @ 50708 @ @ 1Po
Ensure that the environment is well grounded!
The modules are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the modules, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
s: 25 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1Po
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Device Description 17
750-1504 16DO 24V DC 0.5A
s: 26 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansch lüsse/Leistungsko ntakte/Feldversor gung - Überschrif t 3 @ 6\mod_1256294692864_21. doc @ 43664 @ 3 @ 1Po
3.2.2 Power Contacts/Field Supply
Po
s: 27.1 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Si cherheitshinweise/ Vorsicht/Vorsi cht: Verletzungsgefa hr durch scharfkantig e Messerkontakte! @ 6\ mod_1256193279401_21. doc @ 43414 @ @ 1
Risk of injury due to sharp-edged male contacts!
The male contacts are sharp-edged. Handle the module carefully to prevent injury.
s: 27.2 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Ansc hlüsse/Leistungsko ntakte 2 LK (Messer/ Feder) @ 7\modPo
_1266317883167_21.doc @ 50688 @ @ 1
The I/O module 750-1504 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as male contacts and the contacts on the right side as spring
contacts.
Table 4: Power jumper contacts
Connection Type Number Function
1 Blade contact 2
Infeed of the field
supply voltage
(UVand 0 V)
12
12
Figure 3: Power
jumper contacts
2 Spring contact 2
Forwarding of the
field supply voltage
(UVand 0 V)
Po
s: 27.3 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Si cherheitshinweise/ Achtung/Achtun g: Maximaler Strom Leistung skontakte 10 A @ 3\mod_122649 9143500_21.doc @ 25029 @ @ 1
Do not exceed maximum current via power contacts!
The maximum current to flow through the power contacts is 10 A.
Greater currents can damage the power contacts.
When configuring the system, ensure that this current is not exceeded. If
exceeded, an additional potential feed module must be used.
s: 27.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Si cherheitshinweise/ Hinweis/Hinweis: Potentialeinspei seklemme für Erde einsetz en! @ 3\mod_1226499037468_2 1.doc @ 25023 @ @ 1Po
Use potential feed module for Ground (earth)!
The I/O module has no power contacts for PE intake and transfer. Use a potential
feed module when a PE feed is needed for the subsequent I/O modules.
s: 28 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1Po
Manual
Version 1.0.1

18 Device Description WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
s: 29 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansch lüsse/CAGE CLAMP-Ansc hlüsse - Überschrif t 3 @ 6\mod_1256296337770_21. doc @ 43674 @ 3 @ 1Po
3.2.3 CAGE CLAMP®Connections
Po
s: 30 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansch lüsse/Digitalau sgangsklemmen/Ansc hlüsse 750-150x 16 DO CAGE CLA MP@ 3\ mod_1232518817578_21. doc @ 26488 @ @ 1
Table 5: Connections Connection Channel Designation Function
1 1
Output
DO 1 Output DO 1: Signal voltage
2 2
Output
DO 2 Output DO 2: Signal voltage
.
.
.
15 15
Output
DO 15 Output DO 15: Signal voltage
16 16
Output
DO 16 Output DO 16: Signal voltage
Power
jumper
contacts - +24 V Field supply voltage +24 V
DO 15
DO 1
DO 16
DO 2
DO 5 DO 6
DO 11 DO 12
DO 7 DO 8
DO 9 DO 10
DO 13 DO 14
DO 3 DO 4
+24 V
0V
+24 V
0V
Figure 4: Connections
Power
jumper
contacts - 0 V Field supply voltage 0 V
Po
s: 31 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

WAGO-I/O-SYSTEM 750 Device Description 19
750-1504 16DO 24V DC 0.5A
s: 32 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Anzeigeelemente - Überschrift 2 @ 4\ mod_1240984390875_21.doc @ 31964 @ 2 @ 1Po
3.3 Display Elements
Po
s: 33 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Anzei geelemente/Digital ausgangsklemmen/Anz eigeelemente 750-15 xx 16 DO @ 3\mod_1232460663781_ 21.doc @ 26393 @ @ 1
Table 6: Display elements
LED Channel Desig-
nation State Function
off Output DO 1: Signal voltage (0)
1 1
State
DO 1 green Output DO 1: Signal voltage (1)
off Output DO 2: Signal voltage (0)
2 2
State
DO 2 green Output DO 2: Signal voltage (1)
.
.
.
off Output DO 15: Signal voltage (0)
15 15 State
DO 15 green Output DO 15: Signal voltage (1)
off Output DO 16: Signal voltage (0)
13 14
750-150X
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
DO 1
DO 15
DO 2
DO 16
Figure 5: Display
elements
16 16 State
DO 16 green Output DO 16: Signal voltage (1)
Po
s: 34 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Bedienelemente - Überschrift 2 @ 4\mod_123919 1655456_21.doc @ 30439 @ 2 @ 1
3.4 Operating Elements
Po
s: 35 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Bedie nelemente/Bediene lemente Busklemme 750- xxxx nicht vorhanden @ 4\ mod_1236322031125_21.d oc @ 28063 @ @ 1
The I/O module 750-1504 has no operating elements.
Po
s: 36 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1

20 Device Description WAGO-I/O-SYSTEM 750
750-1504 16DO 24V DC 0.5A
s: 37 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Schematisches Scha ltbild - Überschr ift 2 @ 4\mod_1240984441312 _21.doc @ 31967 @ 2 @ 1Po
3.5 Schematic Diagram
Po
s: 38 /Serie 750 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Schemati sche Schaltbilder/ Digitalausgangsk lemmen/Schematisches S chaltbild 750-15xx 16 D O HSS CAGE CLAMP @ 3\mod_1232468 079015_21.doc @ 26437 @ @ 1
750-15XX
12
34
56
78
910
11 12
13 14
15 16
DO 15
DO 1
DO 16
DO 2
DO 5 DO 6
DO 11 DO 12
DO 7 DO 8
DO 9 DO 10
DO 13 DO 14
DO 3 DO 4
+24 V
0V
DO
DO
24 V
0V
270 pF
10 nF 10 nF
10 nF
Figure 6: Schematic diagram
Po
s: 39 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1
Manual
Version 1.0.1