Teledyne LeCroy User manual

Introduction
Use this document for quick installation and setup.
Teledyne LeCroy’s PCIe to SFF-8639 x4 NMVe/SCSIe Port A Adapter card
provides a quick and simple means for test and debug of Solid State Drives (SSDs)
based on PCI Express (PCIe®) protocols. It supports data rates of 2.5 GT/s (Gen1),
5 GT/s (Gen2) and 8 GT/s (Gen3). The PCIe to SFF-8639 x2 NVMe/SCSIe PortB
Adapter looks exactly the same as the Port A adapter except for the silkscreen with
the name of the product. Functionally, the Port B SFF-8639 Adapter works up to X2
since only Lanes 0 and 1 are routed in the PCB from the PCIe edge connector to
the Port B of the SFF-8639 connector.
SFF-8639 Single-Port Adapter Card
1
Components
The adapter package includes the following components:
• SFF-8639 single-port Adapter card
• Power supply +12V @ 3A
• Quick Start Guide (this document)
Inspect the received shipping container for any damage. Unpack the container
and account for each of the system components listed above. Visually inspect
each component for absence of damage.
In the event of damage, notify the shipper and Teledyne LeCroy. Retain all
shipping materials for shipper’s inspection.
2
PCI Express 3.0 to SFF-8639 Adapter
Quick Start

Connections
Perform to the following steps to connect the Adapter (see the image below):
1. Insert the SSF-8639 device under test (DUT) through the 2.5" bracket mak-
ing sure it connects properly in the bottom SSF-8639 connector.
2. Make sure the power for the DUT is sourced correctly using switches SW4,
SW5, SW7, and SW8. The factory default positions are SW1.1 OFF, SW1.2
ON, SW1.3 OFF, SW1.4 OFF, SW4 shunts 1-7, SW5 shunts 2-3, SW7 shunts
1-4, SW8 shunts 1-3. See the tables below to source the correct power for the
DUT.
3. Make sure only switch 2 from the DIP switch array SW1 is in the on position.
The PRSNT# pins configuration is X1 or X4 device is selected using SW1
according to the table.
4. Plug the adapter with the device under test in any PCI Express slot.
5. Connect the power supply to the external power jack (J3) if needed.
PCI Express (PCIe) Interface
(plugs into PCI Express slot)
Device
Under
Test
(DUT)
SW1 SW5 SW4
External power jack J3
12V @ 3A minimum
Note: See section 4 for switch
configurations
SW7 SW8
J8 J9
Note: See section 5 for J8 and J9
pin out
J11
J10
3

Configuration
SW1
Note: Up to X2 for Port B Adapter
SW4
SW5
SW7
Note: 5V from internal regulator is derived from the 12V
power source selected with SW4
SW8
Power Connections
J8 Power Connector
J9 Power Connector
SW1.1 SW1.2 SW1.3 SW1.4 Boot Configuration
ON OFF X X X1
OFF ON X X X4 (see note below)
Others reserved
Shunt 12 V Source Selection
1 --> 7 12V from Host (PCIe Edge connector)
2 --> 8 12V from DC Jack J3
3 --> 9 12V from 6 pin connector J8
4 --> 10 12V from 8 pin connector J9
5 --> 11 12V from SATA connector J11
6 --> 12 12V from Molex connector J10
Shunt 3.3V/5.0V Selection
1 --> 2 3.3V
2 --> 3 5.0V
Shunt 5V Source Selection
1 --> 4 5V from Internal regulator
2 --> 5 5V from Molex connector J10
3 --> 6 5V from SATA connector J11
Shunt 3.3V Source Selection
1 --> 3 3.3V from Host (PCIe Edge connector)
2 --> 4 3.3V from SATA connector J11
Pin Description Pin Description
1 +12V 4 GND
2NC 5 NC
3 +12V 6 GND
Pin Description Pin Description
1 +12V 5 GND
2 +12V 6 NC
3 +12V 7 GND
4NC 8GND
4
5

Test Point Number Test Point Name
TP2 6.5V
TP3 5V_REG
TP4 3.3V_HOST
TP5 PERST
TP6 CLKB_P
TP7 CLKB_N
TP8 IFDET
TP9 DUALPORTEN
TP10 12V_DC_JACK
TP11 12V_SATA
TP12 5V_SATA
TP13 5V_3.3V
Test Point Number Test Point Name
TP14 12V
TP16 3.3V_SATA
TP17 5V
TP18 3.3V
TP19 12V_8_PIN
TP20 12V_6_PIN
TP21 12V_MOLEX
TP22 5V_MOLEX
TP23 GND
TP24 GND
TP25 GND
Copyright
© 2013 Teledyne LeCroy, Inc. All rights reserved. Part Number: 925259-00 Rev B
This document may be printed and reproduced without additional permission, but all copies
should contain this copyright notice.
Trademarks and Servicemarks
Teledyne LeCroy is a trademark of Teledyne LeCroy. All other trademarks are
property of their respective companies.
Changes
Product specifications are subject to change without notice.
Teledyne LeCroy reserves the right to revise the information in this document
without notice or penalty.
Teledyne LeCroy Customer Support
Online Download
Periodically check the Teledyne LeCroy Protocol Solutions Group web site for
software updates and other support related to this product. Software updates are
available to users with a current Maintenance Agreement.
Mail: 3385 Scott Blvd., Santa Clara, CA 95054-3115
Web: teledynelecroy.com/tm/Library/software/PSG
E-mail: [e-mail]
Tel: [phone] (USA and Canada)
Tel: [phone] (worldwide)
Fax: [phone] (worldwide)
6Available Test Points
Environmental Conditions
• Temperature: Operating 32° F to 122° F (0° C to 50° C)
• Temperature: Non-Operating 14° F to 176° F (-10° C to 80° C)
• Humidity: Operating 10% to 90% RH (non-condensing)
7