Temtop C1 User manual
C1
Air Quality Monitor
User Manual
Carbon dioxide(CO2) is a colorless and odorless gas usually derived
from the breath of humans and animals. High CO2concentration
means that fresh air or ventilation is required; otherwise, it may
cause problems such as drowsiness, dizziness, loss of attention,
and cognitive impairment.
Temperature &Humidity may often be ignored. However, they do have
a significant impact on an individual's well-being, comfort, health
and safety, as well as your property. High Humidity may lead to an
increase in household air pollutants, especially the biological contaminants
such as molds, bacteria, viruses, and dust mites; cold, low Humidity
may cause nosebleeds, skin and respiratory irritations, dyspnea, static
electricity, etc.
Do not expose the detector to heavily contaminated environments for long
periods, as this can damage the sensor.
Do not use the detector for long periods in environments with a strong, irritating
smell to ensure accurate measurements.
Do not dismantle the unit yourself. In the event of a defect, contact your dealer
instead, who will liaise with the service center and, if necessary, send the
device in for repair.
Children should only use this device under adult supervision. Keep packaging
materials, such as plastic bags and plastic wrap, out of the reach of children
as they present a choking hazard.
If the battery level shows , please charge the detector in time to avoid
being aected during use (it can also recharge when switched o).
This product is intended for monitoring the health of the indoor environment
only and should not be considered a professional measurement tool.
★
★
★
★
★
★
Buzzer status CO2level
Temperature &Humidity level Battery level &Charging status
Work mode
Health level display area
Magnetic back Vents
Mode button Power button USB port
CO2detection port
Bracket
Temperature &Humidity detection port
CO2
Measuring range: 400-5000ppm
Resolution: 1ppm
Accuracy: ±(40ppm +5%)
(400-2500ppm)
C1
Model
Temperature*
Humidity
Measuring range: 0-99%RH
Resolution: 0.1%RH
Accuracy: ±3%RH
Measuring range: -10-60°C (14-140°F)
Resolution: 0.1°C (-9.9-70°C)
Accuracy: ±0.5°C
When charging the product, the temperature will be ± 0.5 error and will be recovered in
about 10 minutes after the charging is completed.
When the temperature measurement environment suddenly changes, and the temperature
dierence is significant, it takes 3 to 5 minutes of adaptation time.
-10-60°C/0-90%RH
When the product is charging, the data will keep refreshing every 5 seconds.
Note: The above data are from Temtop Laboratory.
About 70 days
About 30 days
Power-saving mode (Sampling interval 10 min)
Performance mode (Sampling interval 1 min)
Segment code screen 3.3 inches
Power-saving mode (Sampling interval 10 min)
Performance mode (Sampling interval 1 min)
Power button
1 )
Press 3s to turn on/o the C1 monitor.
2 )
Short press to turn on/o the alarm.
Buzzer switch Icon
Displayed--buzzer sound on the device is turned on;
Disappears--the buzzer sound is turned o.
The C1 has two working modes, and you can switch the working mode by pressing the
mode button after powering on.
Mode display
1 )Short press to switch between the
work mode (2 dierent types)
2 )Long press 2s to switch between the
temperature unit ( )
Performance mode (Sampling interval 1 min)
CO2sensor works every 1 minutes.
CO2sensor works every 10 minutes.
Note: If the temperature and humidity change is high, it will be refreshed once in 5 seconds;
if the temperature and humidity change is low, it will be refreshed once in 10 seconds.
Mode button
Power-saving mode (Sampling interval 10 min)
2. C1 monitoring function
1 ) When the battery is displayed as empty, please charge it in time, and the charging icon will be
displayed when charging.
2 ) When the battery power is extremely low, the battery icon will flash 3 times and the shut down.
Power display
Charging icon
USB interface
