TERMA INCLUSIVE MARBLE RUN User manual

INCLUSIVE MARBLE RUN PLAY PANEL
USER GUIDE
V.1.0.2022

0
V.1.0.2021
1. INTRODUCTION
Thank you for choosing our product! We believe you would be satisfied using our Inclusive Marble Run
Play Panel.
Inclusive Marble Run Play Panel combines outdoor fun with therapy. Device aims to integrate non-
disabled people and those with disabilities (using wheelchairs), giving them possibility of playing together.
Besides inclusive purpose TERMA Inclusive Marble Run Play Panel provides kinesiotherapy and social
rehabilitation. The device complies with PN-EN 1176 standard.
The device complies with the premise of universal design, which provides ideas of accessibility to all
potential users, physically able-bodied, and with movement impairments.
TERMA Inclusive Marble Run Play Panel is dedicated to be used outdoor, at such a places as outdoor
gyms, parks, accessible recreation areas, private gardens.
The following User Guide provides all instructions refer to correct installation process, safe use and
exploitation of the device.
The Manufacturer reserves the right to change the contents of the User Guide. The updated version of
the User Guide could be downloaded from the Manufacturer's website www.termamed.pl at the
"Download" section.
Manufacturer:
Terma Sp. z o. o
80-298 Gdańsk
Czaple 100
T: [phone]
email : [email protected]
www.termamed.pl

1
V.1.0.R1.2020
2. DEVICE STRUCTURE
Materials:
Inclusive Marble Run Play Panel is made of the following materials:
Construction: steel profile with epoxy primer, powder coated
Front: HDPE board, 12 mm thick
Foundation: concrete class min. B-15
Dimensions:
Device external dimensions: 1670 x 1420 x 188 mm
Total height of the device measured from the ground level: 1470 mm
The distance of the board from the ground level: 701 mm
Other dimensions of the device:
Free fall height: none
Weight (without foundation): 45 kg
The outer diameter of the frame profile section: fi 40
Safety area dimensions: 1500 mm from each edge of the device
Foundation depth: 540 mm
Number of the rolling elements: 2
Diameter of the main profile:
40
Dimension of the longest element: Main construction: 1670 x 1420 x 188 mm
The weight of the heaviest element: Main construction: 45 kg

2
V.1.0.R1.2020
Ground level

3
V.1.0.R1.2020
Inclusive Marble Run Play Panel consists of the following elements:
No
Component
Quantity
[pcs.]
Figure
1
Main construction
1

4
V.1.0.R1.2020
3. INSTALLATION
To ensure the highest level of safety standards for users and caregivers, it is necessary to read and follow
the steps of installation sequence, assembly quality and safety instructions below.
TERMA Inclusive Marble Run Play Panel is dedicated to be installed on a playground. This device
complies with the EN 1176-1 : 2017 standard.
Ensure a comfortable and safe entry for wheelchair access to the device. No shock-absorbing surface is
required around the TERMA Inclusive Marble Run Play Panel. The rigid surfaces are recommended for
wheelchair access. Loose surfaces such as sand or crushed stone are excluded, grass surfaces are not
recommended.
The surface around the device should also not allow the foundations of the structure to be exposed (e.g.
no loose surface such as sand or gravel should be used).
2
Foundation block
(optionally)
1
3
Foundation pin
M10x300
4
4
Nut M10
DIN EN ISO 4032
12
The safety zone cannot overlap the other devices safety zones and the traffic routes!

5
V.1.0.R1.2020
Fig. Safety area
The foundation block should be permanently attached to the ground. Foundations should be at a depth of
min. 200 mm below the ground level.

6
V.1.0.R1.2020
Ground level

7
V.1.0.R1.2020
4. ASSEMBLY
Place of installation
TERMA Inclusive Marble Run Play Panel is designed to be installed in the playground. The safety zone
shall be defined around the equipment which is 150 cm from each edge of the device. The safety zone of
the Inclusive Marble Run Play Panel cannot overlap the other devices safety zones and the traffic routes.
No shock-absorbing surface is not required around the TERMA Inclusive Marble Run Play Panel, but a
wheelchair user must have an easy access.
Tools needed for assembly:
Spade 2 pieces
Rake 1 piece
Spirit level 0, 5 rm 1 piece
17 open-ended or socket wrench 1 piece
Measure 3m 1 piece
Chemical anchor Fischer FIS VL 410 C or Tytan EVOLUTION II 1 pack of 410 ml
Loctite 243 Adhesive 1 pack of 10 ml
Hammer drill with a drill fi 12 min drilling length 180mm
WARNING! The manufacturer does not provide any tools for assembly!
Two people are needed to assemble the TERMA Inclusive Marble Run Play Panel.
To ensure the comfortable and safe access for wheelchair users the rigid surfaces
are recommended. Loose surfaces such as sand or crushed stones are excluded,
grass surfaces are not recommended.
It is forbidden to install the device in geologically unfavorable conditions, i.e. in a
boggy or loose ground causing subsidence of foundations or in a ground where
water appears after the excavation has been made. Geological conditions should
be regulated prior to installation (effective drainage).

8
V.1.0.R1.2020
Next steps of assembly:
1. Digging a hole for a concrete screed or a block
2. Placing the foundation and drilling holes for the pins
3. Placing the pins in the foundation
4. Installing the device on foundation pins
5. Filling the foundations
1. Digging the hole for a concrete screed or concrete block
Tools:
Shovel / spade
Measure 3 meters
There are two options for installing the device in the ground.
Option 1:
Dig holes according to the following drawings. Pour dug holes with B-15 concrete class and wait until it
sets. Go to step 4, to find out how to proceed.
Option 2:
If the device was purchased in a set with concrete cubes, the holes should be dug in accordance with the
drawings below, next the cubes should be placed in the ground, level and check the dimensions, and then
sprinkle with earth to prevent the concrete cubes from moving.

9
V.1.0.R1.2020

10
V.1.0.R1.2020
1. Placing the foundations and drilling holes for the pins
Tools:
Hammer drill with a drill fi 12 min drilling length 140mm
Chemical anchor Fischer FIS VL 410 C or Tytan EVOLUTION II or other with similar properties
17mm spanner / socket wrench
Loctite 243 adhesive
If a concrete screed has been made, the concrete has set and is ready for further work, place the frame
on the concrete and make holes for the anchors in appropriate places. According to the manufacturer
Fischer FIS VL 410 C, a diameter of fi 12 is required for the M10 pin.
No
Component
Quantity
[pcs.]
Figure
1
Main construction
1
2
Foundation block
(optionally)
1
3
Foundation pin
M10x300
4
4
Nut M10
DIN EN ISO 4032
12

11
V.1.0.R1.2020
Install foundation pins in the holes according to the instructions of the chemical anchor manufacturer. The
minimum length of the pin protruding from the foundation is shown in the drawing. Follow the setting time
of the anchors according to the manufacturer's recommendations. The labyrinth should be attached to the
foundations using washers and cap nuts. Before screwing in the nut, coat the thread with Loctite 243.
2. Placing the pins in the foundation
When drilling, be especially careful not to damage the paint coating!
Mounting plate

12
V.1.0.R1.2020
In the next step, install foundation pins in the holes according to the instructions of the manufacturer of
the chemical anchors. The minimum length of the pin protruding from the foundation is shown in the
drawing. Follow the setting time of the anchors according to the manufacturer's recommendations.

13
V.1.0.R1.2020
3. Installing the device on foundation pins
Start by threading two pieces of nuts onto each stud, as in the first picture below, with the top nut
approximately 30mm above the foundation surface.
In the next step, place the main structure on the pins so that the foundation plate rests on the top nuts.
Then, using a spirit level, level the device by adjusting its position with nuts so as to set the bearing column
vertically.

14
V.1.0.R1.2020
The last step is to fix the structure with locknuts. Use Loctite 243 glue before screwing them onto the pins.
5. FUNCTIONAL TESTS BEFORE COMMISSIONING THE DEVICE
Before putting the device into use, check the following functionalities to confirm the safety of users and
correct installation:
- stability of the device mounting on the foundation,
- smooth roll of the elements.

15
V.1.0.R1.2020
6. MAINTENANCE, INSPECTION, REPAIRS
It is recommended to keep a book of inspections of devices in accordance with PN-EN 1176 standard.
It is recommended to use the following types of inspections, to eliminate the potential risks for users and
determine the need for service or maintenance:
-Routine visual inspection carried out every 1-7 days. Its purpose is to identify hazards that may
result from normal use, acts of vandalism or weather conditions. Pay attention to the cleanliness of
the surface around the Inclusive Marble Run Play Panel and the access ramps (glass, stones,
packaging, etc.).
-Functional inspection carried out every 3 months. It refers to verify the correct operation of the
device in terms of functionality. A functional inspection is a more detailed inspection than a routine
inspection, checking the operation (functionality) and stability of the device in detail, mainly in terms
of its wear.
Check:
- the quality of the varnish coating,
- no play in setting in the ground,
- smooth roll of the elements.
The condition of the smoothed surfaces should also be checked, as well as any protruding, sharp
elements, edges, protruding screws. The assessment also covers the degree of strength of the entire
structure and the unavailability of the edges or surfaces of the foundations to the user.
-Annual main inspection carried out to establish the general condition of the equipment in relation to
the safety level. It is recommended to pay special attention to factory-sealed (non-dismountable)
parts. Annual inspection may require disassembly of the device and sending to Manufacturer for
service.
Contact the Manufacturer to explain the malfunction and take corrective actions . The principles of
warranty repairs and service are described in this manual.
In the event of a failure of devices or any malfunctions in their operation, the
devices should be secured against users until the damage is removed by
fencing it with a construction signal tape with a suspended sign informing
about the damage, for example: "WARNING DEVICE FAILURE".

16
V.1.0.R1.2020
Maintenance
The device has no parts that require periodic maintenance. If any irregularities in operation are noticed
during periodic inspections, diagnose the cause and replace the worn parts.
As the device is based on one pole, in accordance with the recommendations of the PN-EN 1176
standard, increased controls should be applied in terms of the stability of the device and the quality of its
connection to the foundation.
Spare parts list:
List of the spare parts
Number
Name
Number
of
pieces
Illustration
1
Rolling element
2
2
Front panel
1
3
Handle
2

17
V.1.0.R1.2020
Fig. Location of the spare parts

18
V.1.0.R1.2020
7. HOW TO USE INCLUSIVE MARBLE RUN PLAY PANEL
The Inclusive Marble Run Play Panel is dedicated for both non-disabled and disable (those with physical
disabilities, using wheelchairs, with intellectual disability or disability causing limits in the upper limbs
functions) users. The device is designed for users from 3 years of age.
Options of using the device:
-One person with a disability, without leaving the wheelchair, and at the same time 1 disabled person,
-Two people with disabilities, without leaving the wheelchair,
-Two non-disabled people,
-One person with a disability,
-One non-disabled person.
WARNING!
It is forbidden to climb over the device!
WARNING! It is forbidden to overload the device!
Before using the device, it is absolutely necessary to read this User Guide and
follow the guidelines.
TERMA Sp. z o.o. or a service designated by the manufacturer are the only entity
that can perform repairs and inspections. The manufacturer is not responsible for
modernization and repairs made by other entities.
In the case of any device damage or any user injury, report the incident to the
manufacturer immediately. Additionally, please complete the “Incident Report
Form”and send it to the Manufacturer by e-mail or letter. The “Incident Report
Form”is included in this User Guide and on the website www.termamed.pl in the
“Download”tab.