Terra Bound Solutions Playtopia Block Instruction sheet

Block Climber Installation Guideline
This space intentionally left blank.
Age Group:
2-12 Years
Recommended Crew:
Minimum 1-2 People
Tools Required for Assembly:
T-30 TORX Bit
3/16” x 6” Drill Bit
Post Hole Digger / Shovel / Auger
Tape Measure
Level
High Speed 3/8” electric drill w/ clutch
Installation Time:
15 minutes – 30 minutes
Concrete Required:
1.1781 cu ft. per post
Note: Concrete must have a minimum rating of 2,500 psi and must be mixed per
manufacturers recommendation.
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 1

Block Climber Installation Guideline
Standard Hardware
5/16” x 5” RSS
Stainless
5/16” x 4” RSS
Stainless
5/16” x 3-1/8”
RSS Stainless
5/16” x 2-1/2”
RSS Stainless
1/4” x 2-1/2”
RSS Stainless
#10 x 2-1/2”
R4 Stainless
NOT TO SCALE!
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 2

Block Climber Installation Guideline
Block Climber shown is for 48” platform height.
Side view of Block Climber
Standard Block Climbers
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 3

Block Climber Installation Guideline
Check off all items received, against the packing list. Notify your local sales representative
immediately of any items that are missing or that may be damaged.
Before beginning your playground installation, make sure that youhave reviewed “Playtopia’s
Installation Guideline Manual” that was provided with your playground. If you did not receive
acopy of the manual please contact your local sales representative tohave a copy mailed or
emailed toyou.
TERRABOUND SOLUTIONS IS NOT
RESPONSIBLE
FOR ITEMS DISCOVERED MISSING
AFTER 72 HOURS FROM TIME OF
DELIVERY.
Pre-Installation Check
PRE-DRILLING IS REQUIRED. ALL LOCATIONS WHERE
HARDWARE IS TO BE FA
STENED REQUIRES PRE-
DRILLING TO ENSURE PROPER INSTALLATION AND
STRUCTURAL INTEGRITY. WE ARE NOT RESPONSIBLE
FOR INSTALLATION OR STRUCTURAL ISSUES THAT
ARISE FROM NOT PRE-DRILLING ATTACHMENTS.
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 4

Block Climber Installation Guideline
The Playtopia Block Climber is made so that top outer lip of the climber (A) meets flush against the bottom lip of the deck platform
(B).
Block Climber Assembly
A
B
Post removed to show
Block Climber location.
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 5

Block Climber Installation Guideline
When the Block Climber is ready to be fastened pre-drill through the 2 mounting holes located on the underside of the climber as
shown with a 3/16” bit. Fasten (4) 5/16”x 3-1/8” RSS SS Screws - (2) through each side - and into the post until the block climber is
secured in place.
This space intentionally left blank.
Block Climber Assembly Contd.
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 6

Block Climber Installation Guideline
Once your block climber is fastened to the posts locate the block
climber support legs (A) and ready them for assembly to the
inside of the block climber frame.
Place one support leg inside the block climber frame and
fasten (2) 5/16” x 3-1/8” RSS SS Screws through the pilot
holes of the support leg and into the block climber frame.
Repeat the same step for the opposing support leg.
This space intentionally left blank.
Block Climber Assembly Contd.
A
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 7

Block Climber Installation Guideline
For standard post footer requirements see page 11.
Block Climber Footer
Concrete
Footer
Safety
Surfacing
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 8

Block Climber Installation Guideline
24” Block Climber
32” Block Climber
40” Block Climber
48” Block Climber
Block Climber Footer
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 9

Block Climber Installation Guideline
56” Block Climber
64” Block Climber
72” Block Climber
DATE: 4/23/2014 BLOCK CLIMBER INSTALLATION GUIDELINES
Page 10