Terra HSA001M User manual

Draugystes str. 22, LT-51256 Kaunas, Lithuania, tel.: +370 37 - 31 34 44, fax: +370 37 - 31 35 55
E-mail: [email protected], http://www.terraelectronics.com
Splitband amplier HSA001M
Product description
The amplier is designed in splitband technology for amplifying SAT IF and terrestrial TV signals. Amplier has one input
and one output. TERR band and SAT IF band amplier has separate gain regulators and xed slope pre-correction.
DC+22 kHz signal pass through the amplier.
This amplier is designed for indoor use only.
Safety instructions
Installation of the amplier must be done according IEC60728-11 and national safety standards.
The amplier is powered from mains 230 V~. This voltage is dangerous to life.
Any repairs must be done by a qualied personnel.
The amplier is double isolated from the mains 230 V~.
Do not remove the cover of the power supply section, without disconnecting the unit from the mains supply.
Do not plug the amplier into the mains supply if the power cord or plug is damaged.
Do not plug the amplier into the mains supply until all cables have been connected correctly.
To disconnect the amplier completely, disconnect plug from the mains socket.
The mains socket must be easily accessible.
The amplier shall not be exposed to dripping or splashing water and no objects lled with liquids, such as vases, shall
be placed on it.
Avoid placing amplier next to central heating components, near highly combustible materials and in areas of high humidity.
No naked ame sources, such as lighted candles, should be placed on amplier.
If the amplier has been kept in cold conditions for a long time, keep it in a warm room no less than 2 hours before
plugging into the mains.
Do not insert any objects into ventilation openings.
The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths,
curtains.
Mount the amplier in vertical position with RF input connectors underneath.
From top, front and bottom of installed amplier must be at least 10 cm free space.
External view and operating controls
Vers. 1.01
Type HSA001M
Frequency range SAT IF 950- 2400 MHz
Terr. TV 47-862 MHz
Gain SAT IF 18-25 dB (pre-correction)
Terr. TV 14-18 dB (pre-correction)
Gain adjustment SAT IF 10 dB
Terr. TV 15 dB
Input and output return loss SAT IF ≥10 dB
Terr. TV ≥10 dB
SAT IF 115 dBµV (2 equal carriers)
Maximal output level
IMD3=35 dB(EN60728-3)
Maximal output level Terr. TV 110 dBµV
IMD3=60 dB (DIN45004B)
DC pass 24 V max. 400 mA max.
Supply voltage limit values, 198-250 V~ 50/60 Hz 4 W
power consumption
Temperature range -20o÷ +50oC
Dimensions 133x73x39 mm/0.36 kg
Installation
The amplier should be mounted on vertical surface with connectors underneath in order to ensure good ventilation
conditions.
The amplier must be xed with steel screws Ø 3.5-4 mm. The screws are not included in a package.
Connect the amplier into the mains supply lastly.
Technical characteristics
Caution!
Risk of electric shock.
This product complies with the relevant clauses of the European Directive 2002/96/EC. The unit must be recycled
or discarded according to applicable local and national regulations.
Equipment intended for indoor usage only.
Equipment is double insulated from the mains, with functional earthing.
Functional earthing. Connect to the main potential equalization.
This product is in accordance to following norms of EU: EMC norm EN50083-2, safety norm EN62368-1,
RoHS norm EN50581.
This product is in accordance with Custom Union Technical Regulations: “Electromagnetic compatibility of technical
equipment“ CU TR 020/2011, “On safety of low-voltage equipment“ CU TR 004/2011.
mounting pattern
mounting hole
mounting
hole
RF output
RF input
Variable attenuator
SAT IF amplifier
Screwdriver
Power cord
Variable attenuator
TERR band amplifier
Supply voltage
indicator
Functional
grounding
clamp

Draugystes str. 22, LT-51256 Kaunas, Lithuania, tel.: +370 37 - 31 34 44, fax: +370 37 - 31 35 55
E-mail: [email protected], http://www.terraelectronics.com
Splitband amplier HSA001M
Product description
The amplier is designed in splitband technology for amplifying SAT IF and terrestrial TV signals. Amplier has one input
and one output. TERR band and SAT IF band amplier has separate gain regulators and xed slope pre-correction.
DC+22 kHz signal pass through the amplier.
This amplier is designed for indoor use only.
Safety instructions
Installation of the amplier must be done according IEC60728-11 and national safety standards.
The amplier is powered from mains 230 V~. This voltage is dangerous to life.
Any repairs must be done by a qualied personnel.
The amplier is double isolated from the mains 230 V~.
Do not remove the cover of the power supply section, without disconnecting the unit from the mains supply.
Do not plug the amplier into the mains supply if the power cord or plug is damaged.
Do not plug the amplier into the mains supply until all cables have been connected correctly.
To disconnect the amplier completely, disconnect plug from the mains socket.
The mains socket must be easily accessible.
The amplier shall not be exposed to dripping or splashing water and no objects lled with liquids, such as vases, shall
be placed on it.
Avoid placing amplier next to central heating components, near highly combustible materials and in areas of high humidity.
No naked ame sources, such as lighted candles, should be placed on amplier.
If the amplier has been kept in cold conditions for a long time, keep it in a warm room no less than 2 hours before
plugging into the mains.
Do not insert any objects into ventilation openings.
The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths,
curtains.
Mount the amplier in vertical position with RF input connectors underneath.
From top, front and bottom of installed amplier must be at least 10 cm free space.
External view and operating controls
Vers. 1.01
Type HSA001M
Frequency range SAT IF 950- 2400 MHz
Terr. TV 47-862 MHz
Gain SAT IF 18-25 dB (pre-correction)
Terr. TV 14-18 dB (pre-correction)
Gain adjustment SAT IF 10 dB
Terr. TV 15 dB
Input and output return loss SAT IF ≥10 dB
Terr. TV ≥10 dB
SAT IF 115 dBµV (2 equal carriers)
Maximal output level
IMD3=35 dB(EN60728-3)
Maximal output level Terr. TV 110 dBµV
IMD3=60 dB (DIN45004B)
DC pass 24 V max. 400 mA max.
Supply voltage limit values, 198-250 V~ 50/60 Hz 4 W
power consumption
Temperature range -20o÷ +50oC
Dimensions 133x73x39 mm/0.36 kg
Installation
The amplier should be mounted on vertical surface with connectors underneath in order to ensure good ventilation
conditions.
The amplier must be xed with steel screws Ø 3.5-4 mm. The screws are not included in a package.
Connect the amplier into the mains supply lastly.
Technical characteristics
Caution!
Risk of electric shock.
This product complies with the relevant clauses of the European Directive 2002/96/EC. The unit must be recycled
or discarded according to applicable local and national regulations.
Equipment intended for indoor usage only.
Equipment is double insulated from the mains, with functional earthing.
Functional earthing. Connect to the main potential equalization.
This product is in accordance to following norms of EU: EMC norm EN50083-2, safety norm EN62368-1,
RoHS norm EN50581.
This product is in accordance with Custom Union Technical Regulations: “Electromagnetic compatibility of technical
equipment“ CU TR 020/2011, “On safety of low-voltage equipment“ CU TR 004/2011.
mounting pattern
mounting hole
mounting
hole
RF output
RF input
Variable attenuator
SAT IF amplifier
Screwdriver
Power cord
Variable attenuator
TERR band amplifier
Supply voltage
indicator
Functional
grounding
clamp