Teufel AC 7001 SP Manual

Speaker stand
AC 7001 SP
Technical Description and
Operating Instructions
Proper use
Only use the speaker stand for mounting suitable speak-
ers. You can find a corresponding list on our website
www.teufel.de.Any other use will be deemed as not in ac-
cordance with the instructions and may lead to damage of
property or even persons.
The manufacturer accepts no liability for damage caused
by use not in accordance with the instructions. The unit is
intended for private use.
Before operating the product for the first time,
please read the safety notes and operating instruc-
tions carefully. This is the only way to use all func-
tions safely and reliably. Keep the operating instructions safe
and pass them on to anyone who may own the unit after you.
Notice
The information in this document may change without prior
notice and in no way constitutes any liability on the part of
Lautsprecher Teufel GmbH. No part of these instructions may
be reproduced in any form or be broadcasted in any way elec-
tronically, mechanically, by photocopy or recording without
the written permission of Lautsprecher Teufel GmbH.
Original packaging
If you wish to exercise your right of return, we ask that you
be absolutely sure to hold onto the packaging. We can only
accept the return of a unit WITH THE ORIGINAL PACKAGING.
Empty boxes are not available!
Complaints
In case of a complaint we implicitly need your invoice number
and the serial or lot number for processing. The serial num-
ber is located on the bottom side of the device.
Many thanks for your support!
Contact
Please contact our customer service with any ques-
tions, suggestions or criticism:
Lautsprecher Teufel GmbH
BIKINI Berlin
Budapester Str. 44
10787 Berlin (Germany)
Phone 00800 - 200 300 40 (toll-free)
Fax: +49 (0)30 / 300 930 930
Service: www.teufelaudio.com/service
Contact: www.teufelaudio.com/contact
General notes and information

①1 x base plate
②1 x pipe
③1 x speaker bracket
④1 x counter-sunk screw M6 x 35
⑤2 x counter-sunk screw M4 x 12
⑥4 x cylinder head screw M6 x 30
⑦4 x washer
⑧1 x hexagon wrench
Check that all items have been delivered and that nothing is
damaged.
If anything is missing or damaged, please contact our service
department (see page 1). Do not use a product if it is dam-
aged.
Note:
You can find a current list with all the speakers that are
suitable for use with this speaker stand on our website at
www.teufel.de
Product contents
⑥
⑦
⑧
③
④
⑤
①
②
Danger Danger of injury/damage!
Incorrect location may result in damage.
• Place the speakers in such a way that they cannot be
knocked over unseen and make sure that the cables do
not pose a trip hazard.
• Do not place the speakers near or directly above sources
of heat (e.g. heaters, ovens, other heat generating equip-
ment such as amplifiers etc.).
• Avoid direct sunlight at the setup location.
Danger Danger to children!
Children can become trapped in the packing film
when playing and suffocate.
• Do not allow children to play with the unit or the packing
film. Danger of suffocation.
• Ensure that children do not remove small parts from the
unit or take them off of the unit (e.g. control knobs or plug
adapters). They could swallow the parts and choke.
Warning of damage to property!
The isolation pads can produce discolouration on
sensitive surfaces.
• On parquet, varnished wood and similar surfaces, you
should stick felt gliders to the rubber feet of the speaker
stand or put blankets or small carpets under them. This
will prevent discolouration of the floor over the long term.
Safety notes

Assembly
[ ⑥⑦
①
②
③
④
M
[
⑤
1. Screw the pipe ②on the base plate ①using four screws
⑥and four washers ⑦. The big hole on the upper end is
the cable feedthrough which should point to the back.
2. Run the speaker cable through the upper hole and through
the pipe until it extends somewhat out of the opening in
the base plate. Then pull it through until there is sufficient
length left for connecting the speaker at the top.
3. Screw the speaker bracket ③on the speaker from below
using the screw ④. The Mmark must point to the front in
the process.
4. Place the speaker with the speaker bracket on the pipe
and screw the bracket on the pipe through the bore holes
using two screws ⑤.
5. Connect the speaker cables as described in the operating
instructions for the speakers.

Max. carrying capacity: 15 kg
Height: 685 mm
Base plate dimensions: 250 x 370 mm
You can obtain further technical data on our website.
Technical data
Noresponsibilityisassumedforthecorrectnessofthisinformation.Technicalchanges,typographicalerrorsandothererrorsreserved.InstructionNo.199912_20220111_EN/HC-HAM
Please contact our customer service department with any questions, suggestions, or
complaints:
Lautsprecher Teufel GmbH
BIKINI Berlin
Budapester Str. 44
10787 Berlin (Germany)
www.teufelaudio.com
Phone.: [phone] (toll-free)
Fax: +49 (0)30 - 300 930 930
Service: www.teufelaudio.com/service
Contact: www.teufelaudio.com/contact
No responsibility is assumed for the
correctness of this information.
Technical changes, typographical
errors and other errors reserved.