Tevion AP-DVBT52 User manual

Digital SetTopBoxwith inbuilt DVD Player
Instruction Manual • Model Number AP-DVBT52
After Sales Support
TEL: [phone]

After Sales Support TEL: [phone]
What your 1year warranty means
Great care has gone into the manufacture of this product and it should therefore
provide you with years of good service when used properly. In the event of
date of purchase, we will remedy the problem as quickly as possible once it has
been brought to our attention. In the unlikely event of such an occurrence, or if
you require any information about the product please contact us via our after
sales support services, details of which can be found in this manual and on the
product itself.
DVD Player with DVBT

WARNING:TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS
APPLIANCE TO PAIN OR MOISTURE.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK.DO NOT REMOVE COVER
(OR BACK).NO USER SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightening flash with arrowead symbol,within an equilateral triangle,is intended the
alert the user to the presence of uninsulated dangerous voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Note:Where the mains plug is used as the disconnect device, the disconnect devices shall remain
readily operable.
Laser product symbol:located on the rear panel of the unit,indicate this player is a class laser
product,only use weak laser and no hazardous radiation outside of the unit.
1.Read through this instruction manual before installation and use.
2.Do not touch the power plug with wet hand.
3.Switch off the main power when the unit is not in use.(Disconnect the power plug from the power
outlet when you do not intend to use the unit for a prolonged period of time.) Before moving the
unit,remove the disc from the unit tray first.
4.Do not open the cover or touch any of the components exposed out of the unit,only for qualified
technicians.
5.Do not expose the unit under direct sunlight or nearby objects that radiate heat to avoid damage
the unit.
6.Do not place the unit in moist and humid conditions,which effect the pick-up of the unit lead to out
of work.
7.Place the unit on a flat surface and ventilative condition.Please ensure the ventilation holes are
not covered to avoid overheating and malfunction.
8. Clear the panel and case with soft dry cloth only,do not apply any king of thinner,alcohol
osprays.
9.The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids,such as vases,shall be placed on the apparatus
10.unplug the apparatus when not using for a long time oriented to disconnect from the Mains
power.
Macrovision:
This product incorporates copy right protection technology that is protected by method claims of
certain U.S patents and other intellectual property rights owned by Macrovision Corporation,
and is intended for home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation.Reverse engineering or disassembly is prohibited.
DOLBY PRO LOGIC:
Manufactured under license from Dolby Laboratories.Dolby,Pro Logic and the double-D symbol
are trademarks of Dolby Laboratories.

1.Table of Contents
1 Table of Contents
System Setup
6
2 Front Panel and Rear panel
3 Remote Controller
13 Trouble shooting
14 Technical Specification
4 CD&MP3 Playing
4 Picture CD Playback
5
1
5 Connecting a memory card
Connecting a USB Memory Stick

2.Front Panel and Rear panel
Rear panel
12 3
1.STANDBY
4
567
2.OPEN/CLOSE
3.PLAY/PAUSE
4.STOP
5.DISC TRAY
6.LED DISPLAY
7.MS/SD/MMC CARD&USB
/
4
1
2 3 4
5 6
1.RF IN/OUT
2.VIDEO OUTPUT
3.YUV COMPONENT OUTPUT
4.5.1CH HOME THEATRE OUTPUT
5.S-VIDEO OUTPUT
6.COAXIAL OUTPUT
2
Front Panel

3.Remote Controller
3
SETUP/FAV: Under DVD mode, it performs as Set-Up function Under DVB mode, it performs as FAV
function
PREVIOUS/PAGE UP/NEXT/PAGE DOWN:Under DVD Mode, it performs as PREVIOUS/NEXT function
Under DVB Mode, it performs as PAGE UP/PAGE DOWN function
point the remote control directly at the remote sensor on the front of the DVD Player,not the TV.
Note:
The tray can only be opened in DVD status.
Remote control uses two AAA batteries
PROG/EPG:Programming/Electronic Program Guide.Under DVD mode:pressPRGE/EPG’’to
Access interface for programming and editing, where disc content can be programmed for playing
with direction and number buttons. Under DVB mode:it is used to access Electronic Program
Guide(EPG).
COLOR KEYS:Teletext Red/Blue/Green/Yellow key.
Remote Control
Unless stated otherwise,the remote control can operate all the features of the DVD Player,always
9
10
11
12
13
1
2
3
4
5
6
7
8
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
30.PREVIOUS/PAGE UP/NEXT/PAGE DOWN
1.DISPLAY
2.STANDBY
5.NUMBER BUTTONS
MENU/PBC
6.GOTO
7.STOP
8.PLAY/PAUSE
11.
12.ENTER
13.LEFT
20.OPEN/CLOSE
22.DVD/DVB
19.MUTE
24.AUDIO
26.ANGLE
25.SUBTITLE
27.RETURN
28.SLOW
29.STEP
21.ZOOM
34.VOLUME-/+
18.COLOR KEYS
4.REPEAT
3.A-B
14.SETUP/FAV
9.FAST REVERSE/
FAST FORWARD
10.UP/CH+
16.TITLE/TTX
17.TV/RADIO
23.SOURCE
15.DOWN/CH-
31.EXIT
32.RIGHT
33.PROG/EPG
Note:
DVD Mode -DVD Player
DVB Mode -Set Top Box

DVD OPERATIONS
4.CD&MP3 Playing
5. Picture CD Playback
4
After Sales Support TEL:[phone]
The player will automatically play the first song (file) in the menu.You can use number
keys to select your favorite song (file).Press arrow keys to select the file,and the
cursor will move at time,press ENTER to confirm,the player will play this song
selected by cursor in the file window.
PROG
1.Put in a MP3/CD format disc.
2.There is edit mode, at the right of the list, Press Enter to choose Edit mode, first,
then press Enter, to choose the song which need to program playing in the list,
please move the cursor to the Add to program,at the right side, then press
Enter,to confirm it,it's ok. Please move the cursor to the program list to choose
program playing.
3.To clear the program, it must be in the stop status and after chosen the song which
need to clear, then move the cursor to the Clear to program,then press Enter to
confirm it, it's ok.
Image rotation
There are three modes to rotate apicture:90 cw,180 cw,270 cw.Those operations
are Allowed only whenapicture isbeing displayed normally andwill becancelled
automatically whenanew picture isdisplayed.Press ANGLErepeatedly,youcan
selectthedifferentrotationmode:Wipe downtransition,wipe uptransition,center
in transition,center outtransitionandso on.Imagezoom.press ZOOMkey under
anypicture playback,may realizethepicture zoomfunction.Zoomin to :1X,2X,3X.
The max size of JPEG picture that can be supported:3840x3840 pixels.
Apicture CD has the size and shape of a regular CD.

6.Connecting a USB Memory Stick
1)Power-on the unit.
2)Make sure no disc has been inserted inside the tray.
3)Insert a usb key inside the connector.
4)Press the source key from the remote control to start.
Remark: Depending on the capacity of the device, the reading can take more than 1
minute before lauching the video.
DVD OPERATIONS
-Once you have plugged your device to the unit, you may need to switch
on the USB device before it can operate.
-This unit does not support a direct USB connection with a computer. You
need to use a USB device, a MP3 player or a PMP (Portable multimedia
Player with hard disk).
-If you are using a USB external hard disk: you need to connect your
device simultaneously to an external power source and to the unit. If you
are using a self-powered PMP, make sure that the battery is sufficiently
loaded. -Check that the files system of your USB device is formatted into
the FAT or FAT 32 format. USB device formatted into NTFS are not
compatible with this unit.
Caution: if you attempt to modify your file system, formatting your device
will erase all data. Please refer to your USB device's instruction manual
first.
The unit cannot
read my USB
device.
5
After Sales Support TEL:[phone]
7.Connecting a memory card
1)Power-on the unit.
2)Make sure no disc has been inserted inside the .
3)Insert a compatible memory card inside the connector.
4)The DVD player will automatically read the photos stored on the memory card.
Notice:Depending on capacity of the device,the reading can take more then 1
minute before lauching the video.
slot
My player does not
recognize my
Memory Card when
plugged to the DVD
player.
Would you please refer first to the instructions describing how to
use memory cards with this machine.
Also check that the card's format is compatible with the machine
(eg. SD / MS / MMC).
If the problem still occurs: This product has been tested with
the majority of the market's memory cards. However, because
of the vast numbers of cards put into the market, we cannot
guarantee a full compatibility with all the memory cards.

8.2.1 Aspect Ratio
4:3 Choosing this setting if your DVD player is connected to a standard TV.You can fill the movie
to the entire screen of your TV.This might mean that parts of the picture(the left and right edges)
won’t be seen.
16:9:Choose this setting if your DVD player is connected to wide screen TV. If you choose
this setting and you do not have a wide screen TV,the images on the screen may appear
distorted due to vertical compression.
Notes:
The image display ratio is related to the recorded disc format.Some disc can not
display images in the aspect ration you choose.If you play a disc recorded in 4:3
format on a wide screen TV,black bars will appear on the left and right side of the
screen.You must adjust the screen setting depending on the type of the television
you have.
After Sales Support TEL:[phone]
DVD OPERATIONS
6
System Setup
8.
8.2.2 View Mode
With this option you can select the different video vision mode on the screen.
DVD menu setup
Press the SETUP button on the remote control,the SETUP MENU(main) will be
displayed.After accessing the setup menu,press the direction buttons for up and down
movement to select an item desired,then press the ENTER button to confirm.Press LEFT
direction button return to the menu of upper level.To exit the setup,press the SETUP button
again.In the SETUP MENU,you may choose any of the following Iptions as you like.
8.1.1 Language
Use this item to select the language.
8.1.2 Subtitle
This option provides the preset subtitle language.Follow the operating instructions stated
in DVD MENU SETUP in combination with the desired option.
8.1.3 Audio
Follow the operating instructions stated in DVD MENU SETUP in combination with
the desired option.This option provides the built-in disc dubbing language options.
8.1.4 DVD Menu
This option provides the movie menu language options.Follow the operating
instructions stated in DVDMENU SETUP in combination with the desired option.
8.2 VIDEO SETUP
Select Video in the setup menu.
8.1 Language Setup
Select Language in the setup menu .

After Sales Support TEL:[phone]
DVD OPERATIONS
8.3 Audio setup
Select Audio in the setup menu .
7
8.2.4 Video Out
Selecting the Video Output setting to switch between different video outputs.
S-Video:Set the video output to S-Video output.
Component:Set the video output to interlacing component output.
P-Scan:Set the video output to progressive component output.
8.2.3 TV System
This product supports output of various systems,including Auto,NTSC,PAL.If your TV set has
only NTSC or PAL system,the screen will blink and become colorless when a wrong system is
selected.
Note:For more information of output format,refer to the instructions or your TV set.
(PAL is the standard for Australia)
8.3.1 Bass Management
To enable or disable the Bass Management during operation of the player.
On = Enable the Bass Management.
Off = Disable the Bass Management.
HOME THEATRE SETUP
8.3.2 Front Speakers
To adjust the front speakers output to work in harmony with the audio equipment
(e.g.receiver, speakers) connected to the player.When Bass Management is On, the
following options are available:
Large : Support signal frequency lower than 200Hz.
Small : Support signal frequency higher than 200Hz.
If the connected speaker supports signal lower than 200Hz, it is best to select large;
If not, you shall select Small.
8.3.3 Center Speaker
Selection of Large or Small is same with that of front speaker. The speaker will have
no signal output if set to None.
Notes:
If the Subwoofer is On, Center is set to None or Small, and bass from the center
channel is redirected to the subwoofer. If the content contains a discrete subwoofer
channel, it is also sent to the subwoofer. If the Subwoofer is Off, Center is set to
None or small, and bass from the center channel is redirected to the left and right
channels. If the content contains a discrete subwoofer channel, it is discarded.
8.3.4 Surround Speakers
Selection of Large or Small is same with that of front speaker. The speaker will have
no signal output if set to None.

DVD OPERATIONS
8
After Sales Support TEL:[phone]
Note:
Bass Management is not available for MP3 or WMA bitstream ; therefore, it will be
disabled during the playback of those streams.
8.3.6 Center Delay
Selecting the Center Delay setting allows the user to enable/disable the center
output delay.
8.3.7 Surr. Delay
Selecting the Surr. Delay setting allows the user to enable/disable the surround
output delay.
8.3.8 Digital output
Selecting the Digital Output setting allows the user to adjust the audio output
S/PDIF ports to work in harmony with the audio equipment(e.g.receiver,speakers)
connected to the player.
Off:Digital audio output is disabled.
PCM:Select this option when you are going to use stereo signals(2 channels).You
should combine this option with the option Lower sampling rate,which we explain
further on .
All:If you select this option the player will use the DVD original audio track.Use this
option when you want to use the Dolby Digital AC3 signals through the optical or
coaxial audio output.
by
Notes:
If the Subwoofer is on, Surround is set to None or Small, and bass from the surround
channels is redirected to the subwoofer. If the content contains a discrete subwoofer
channel, it is also sent to the subwoofer.If the Subwoofer is Off, Surround is set to
None or Small, and bass from the surround channels is redirected to the left and
right channels. If the content contains a discrete subwoofer channel, it is discarded.
8.3.5 Subwoofer
Selecting to enable/disable the subwoofer output when 6 Channel analog output is
used.
The following options are available:
None Subwoofer is off. Bass from center and surround channels is redirected to the
left and right channels. If the content contains a discrete subwoofer channel, it is
discarded.
Present Subwoofer is on. Bass from center and surround channels is redirected to
subwoofer.
If the content contains a discrete subwoofer channel, it is also sent to the subwoofer.

DVD OPERATIONS
9
After Sales Support TEL:[phone]
Language
Audio
Subtitle
DVD Menu
Video
Aspect Ratio
View Mode
TV System
Video Out
Audio
Parental Control
Parental Misc
System Setup
Language Use Default settings
Set Password Screen Saver
A flow chart of the menu:
9.
Bass Management
Front Speakers
Center Speaker
Surround Speakers
Subwoofer
Center Delay
Surr.delay
Digital Output
8.4 Rating Setup
Select<Rating> in the setup menu.
Note:Not all DVDS support ratings.
8.4.1 Parental Control
Selecting a Rating allows the user to set the parental control feature of the player
Select Parental Control, and press ENTER to change the different mode.
Note: Unlock the password before setting Parental Control.
8.4.2 Set Password
Use the keys to input
to confirm.
Note: If you your password, please use
8.5 Misc Setup
Select MISC in the setup menu.
8.5.1 Use Default Settings
Reset setup data to factory default and re-load disc.
8.5.2 Screen Saver
On:Screen Saver function will be opened.
Off:Screen function will be closed.
Password setting your four digit (password), then press ENTER
forgot the factory set password is“0000”to
unlock.

10.First time installation
Ensure all the connections are as per the Quick Start Guide. An easy installation
menu will be displayed where you can set different parameters and then run the
channel scan:
1.OSD Language: Use the arrow / buttons to select a language for the on screen
display menu (OSD). Press to go to the next parameter.
2. Region: Use the arrow / buttons to select your country.Press to proceed.
CAUTION
If the wrong country is selected the channel scan may not detect all the channels
available.
3.Auto Scan : Press ok to start the automatic channel scan.When the scan is
completed,the receiver will enter the Viewing mode.
11. Receiver Settings
The first time installation procedure will allow the receiver to be used with its basic
functions however the receiver offers many more advanced features and options that are
illustrated in the following sections.
11.1 Password
To modify some setting and view certain channel locked by the end-user in the Channel menu ,a
password has to be entered. The factory set password is “0000”(four zeros) but it can be
changed by pressing MENU and selecting the setup menu and then Parental Lock.
CAUTION
Take note and keep the new password in a safe place,if you forget your personal
password,use the universal code “0786”to access the parental lock menu and set a
new password.
11.2 Channel Scan
The first time guided installation procedure runs a channel scan and saves any channels
available at that time,however later scans may become necessary if, for instance,a new
channel becomes available or when an existing channel changes frequency.To access the
channel scan function from the viewing mode,press MENU on the remote control to open
the main menu,select Installation and then one of the following options：
1. Auto Scan:An automatic scan of all digital terrestrial channels received in the area by
your antenna Press OK on Search to start the scan.
CAUTION
When a new automatic scan is run,the existing channel list will be lost.
2. Channel Scan (For Expert Users):Set all the parameters displayed on video related to the
Interested channel,then select Search and press OK.
SET TOP BOX(DVB) OPERATIONS
10
After Sales Support TEL:[phone]

11.4 Load Factory Default
The default setting of the receiver can be restored by a general reset. To do so, press
MENU on the remote control, select Tools and then Load Factory Default .
CAUTION
A reset will lose all personal options and features settings saved in the receiver.
11.5 Software Upgrade
When you enter SOFTWARE UPGRADE menu.
12. The Menus
The main menu has 4 sub-menus:
- Channel: Channel list browsing and editing . The edit options include order , change
name, lock and delete TV and radio channels.
- Installation: Useful during installation. Functions include automatic and manual
channel scans.
- Setup: The general receiver configuration. Options to personalize and modify system
parameters, such as OSD language , type of TV system, country and time. system
password and to set the event timers.
- Tools: Practical tools like reset default settings and system information viewing.
CAUTION
The menu is simple and easy to navigate. Use the arrows, ok and number buttons and
always follow the instructions given in the bottom toolbar.
A f lo w c h a rt o f t h e m en u :
DVB OPERATIONS
11
After Sales Support TEL:[phone]
NOTE:In DVB mode,USB jack can only be used to upgrade.
11.3 Time setting
Press MENU on the remote control to open the main menu. Select Setup and then
Region and Time . Three setting options are available under GMT Usage item:
- By Region: The receiver will automatically set the time according to the selected Region.
- Off: The user manually sets date and time.
- User Define: Indicate the Greenwich Mean Time (GMT) time zone .E.g.: Australia has a
time zone of +10 hours(GMT+10:00)
During summer period, if applicable, activate manually the Summer Time parameter.
CAUTION
Some digital terrestrial services transmit information, which is strictly linked to the precise time
setting of the receiver.

Main Menu
Channel
TV Channel List
Delete All F avorites
Radio Channel L list
Delete All
Group Rename
Installation
Auto Scan
Channel Scan
Setup
TV System
OSD Language
Region and Time
Timer Setting
OSD Setting
Parental Lock
Load Factory Default
Tools
Receiver Information
Game
Software Upgrade
After Sales Support TEL:[phone]
DVB OPERATIONS
12

Problem
The standby light not lit
After moving the
receiver to another
room,can’t receive
digital reception
Possible Cause
Mains lead unplugged
Aerial is disconnected
Aerial is damaged/
misaligned
What to do
Check mains lead
Check aerial lead
Check aerial
The aerial feed may come
through a distribution
system which may reduce
the digital signal now
received by the receiver
Try a direct feed from the
antenna
No signal found
Out of digital signal area Check with dealer
No picture or sound Tuned to digital teletext
channel Retune to another
channel
Mosaic blocks in picture
or picture freezes
Aerial may not be
compatible/or damaged Check aerial
Scrambled channel
message Channel is scrambled Select an alternative
channel
Forgotten channel lock
code
Re-install channels to
Cancel channel lock
No response to remote
control
Receiver off
Handset not aimed
correctly
Front panel obstructed
Remote control batteries
are inserted incorrectly
Handset batteries
exhausted
Plug in and turn on receiver
Aim handset at front panel
Check for obstructions
Check batteries direction
Replace remote control
batteries
13. Trouble shooting
13
After Sales Support TEL:[phone]
Troubleshooting
If you experience problems with this receiver or its intallation,please read carefully the relevant
sections of this User Manual and this Troubleshooting section.

Composite:1.0 0.2Vp-p
Load impedance:75 ,lmbalance,negative polarity
14.Technical Specification
14
After Sales Support TEL:[phone]
Mini DIN 4
Item
Demodulation
Connectors
Display
Decoding
Other
Tuner
Specification
Frequency Range
Signal Input Level
Bandwidth
Demodulator
OFDM Modulation
Packet Carries
Guard Interval
RF IN
RF LOOPTHOUGH
COAXIAL
USB
Input
Consumption
Decoder Module
Resolution
Aspect Ratio
Video
Audio
Compliance
Sound mode
VHF: 174MHz to 230 MHz
UHF: 470 MHz to 860 MHz
75 Ohms unbalanced
-78~ -25 dBm
7/8 MHz
COFDM
2K, 8K FFT, SFN and MFN
2K/8K
1/4, 1/8, 1/16, 1/32
IEC 169-2 female connector
IEC 165-2 male connector
PAL, NTSC
720 x 576 (PAL); 720 x 480 (NTSC)
4:3(Letterbox, Pan&Scan), 16:9
MPEG2 Transport MP@ML
MPEG-2 Audio Layer I&II
ETSI EN 300 744 DVB-T Compliance
Right, Left, Stereo
Input Impedance
Composite Video RCA
Compoent Video
S-Video
Power 110 ~240V 50/60Hz
20 W max
USB
2.0
RCA,for SPDIF digital audio output
RCAX3
Frequeny Response 20Hz-20KHZ(at 1KHz 0 dB)
Signal-to Noisy
Ratio(Audio)
Audio Output(Analog
audio)
Video Output
Supported Disc DVD/SVCD/VCD/CD/MP3/Picture/Photo CD
Audio Distortion+Noise
90dB(at 1KHz 0 dB)
-60dB(at 1KHz 0 dB)
2.0 Vrms
-1.0
+0

After Sales Support TEL: 13尲㈰就㈰ 886ᄲ
26
NOTE:
After Sales Support TEL:[phone]

After Sales Support TEL:[phone]

After Sales Support TEL:[phone]