Textron GREENLEE 11147 User manual

INSTRUCTION MANUAL
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
Register this product at www.greenlee.com
99950286 REV 3 © 2013 Greenlee Textron Inc. 7/13
11147
Ultra Tugger®Adapter Package
for use with Greenlee 640 and 6001

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
Description
The Greenlee 640 Tugger®and 6001 Super Tugger®that
you already own can now attach to the same wheeled
carriage that the Ultra Tugger®cable puller uses.
The Ultra Tugger®640/6001 Adapter Package comes
pre-assembled. All you need to do is add your cable
puller and you’ll be pulling cable faster and easier, with
no more anchors to set or chains to mount.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This instruction manual
and any markings on the tool provide information for
avoiding hazards and unsafe practices related to the
use of this tool. Observe all of the safety information
provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with
the safe operation and maintenance procedures for the
following Greenlee tool:
11147 Ultra Tugger®Adapter Package
Replacement manuals are available upon request at no
charge at www.greenlee.com.
All specications are nominal and may change as design
improvements occur. Greenlee Textron Inc. shall not be liable for
damages resulting from misapplication or misuse of its products.
Tugger, Super Tugger and Ultra Tugger are registered trademarks and
VersiBoom is a trademark of Textron Innovations Inc.
KEEP THIS MANUAL
Table of Contents
Description .................................................................... 2
Safety ............................................................................ 2
Purpose of this Manual ................................................. 2
Important Safety Information ..................................... 3-4
Identication—Boom Mount Adapter............................ 5
Specications................................................................ 5
Identication—VersiBoom™ Components.................... 6
Setup
Wheeled Carriage ...................................................... 7
Mounting Components......................................... 8-10
Typical Setups ........................................................ 11-12
Illustration and Parts List—
Boom Mount Adapter.................................................. 13
Accessories
Nose Unit ................................................................. 14
Elbow Unit ............................................................... 15
Couplers .................................................................. 16
Boom Tubes............................................................. 16
T-Stand .................................................................... 17
Wheeled Carriage .................................................... 17

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, dened below,
indicates the severity of the hazard. The message
after the signal word provides information for pre-
venting or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result
in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Read and understand all of the
instructions and safety information
in this manual and your cable puller
manual, before operating or servicing
this tool.
Failure to observe this warning could
result in severe injury or death.
Rope, cable, or a connecting device can break under
tension, causing the rope to whip violently.
• Do not allow any unnecessary personnel to remain
in the area during the pull.
• Do not allow any personnel to stand in line with the
pulling rope.
Failure to observe these warnings could result in
severe injury or death.
Tangle Hazard:
Do not wrap rope around hands,
arms, waist or other body parts.
Do not stand in spent coils or tailed
rope. Hold rope so that it may be
released quickly.
Failure to observe this warning could
result in severe injury or death.
Shear Point:
Do not put ngers through holes in
elbow unit. Rotating parts could cut
off ngers.
Failure to observe this warning could
result in severe injury or death.
When using the wheeled carriage to transport the
VersiBoom™:
• Keep personnel out of the path of transport.
• Evaluate the terrain of over which the carriage is to
move. If in doubt, obtain additional help and move
the carriage slowly.
• Do not transport over inclines of more than 15°.
• Do not transport the carriage with boom tubes
longer than the supplied 3' and 4' tubes.
Failure to observe this warning, could result in severe
injury or death.

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
4
Flying Debris Hazard:
Wear eye protection when using this
tool.
Failure to wear eye protection could
result in severe eye injury from ying
debris.
Falling Object Hazard:
Do not stand directly under a vertical
pull. Cable could fall suddenly from
the conduit.
Failure to observe this warning could
result in severe injury or death.
For use only with Greenlee Model 640 and 6001 cable
pullers.
Use with other pullers may result in insecure mount-
ing and improper rope alignment.
Failure to observe this warning could result in severe
injury or death.
Inspect and verify the maximum
load-bearing capacity or maximum
strength of all structural supports,
pulling system components and
anchoring systems before setting
up the puller. Any component that
cannot withstand the maximum
cable-pulling forces could break and
strike nearby personnel with sufcient
force to cause severe injury
or death.
Note: Keep all decals clean and legible, and replace
when necessary.
IMPORTANT SAFETY INFORMATION

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
5
Identification—Boom Mount Adapter
50111450
Specifications
Weight......................................................................................................20.4 kg (45 lb)
Length........................................................................................................94 cm (37 in)
Width ...........................................................................................................18 cm (7 in)
Height ........................................................................................................30 cm (12 in)
Use with: Greenlee 640 and 6001 Cable Pullers only
Load Rating ....................................................................................................... 6500 lb
Boom Mount Adapter
1. Frame
2. Shaft
3. Roll Pin
4. Hitch Pin Clip
5. Hex Screw
6. Wheel Unit
7. Bushing
1
2
3
4
5
6
7

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
6
1. Elbow Unit (optional)
2. Sight Hole
3. 4' Boom Tube
4. Sight Hole
5. Boom Mount Adapter
6. T-Stand (optional)
7. Wheeled Carriage
Identification—VersiBoom
VersiBoom Components
8. Slip-in Coupler
9. Nose Unit
10. Mounting Pins
11. Hitch Pin Clips
12. 3' Boom Tube (optional)
13. Long Pin
14. Tray
1
12
9
11
1
0
8
2
3
7
14
6
4
5
1
3

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
7
Setup
Wheeled Carriage
Requires: Adequate clearance.
See “Typical Setups.”
1. Mount the boom mount to the wheeled carriage.
Align the boom mount holes with the top holes
in the wheeled carriage, as illustrated. Install a
pin through the top hole in the boom mount and
wheeled carriage. Secure the pin with a hitch pin
clip. Place a second pin in the lower hole.
2. Set puller on boom mount frame so that the puller
mounting feet sit inside the frame opening, between
the two side rails. Slide the puller up against the
stop and chain it down securely.
For use only with Greenlee Model 640 and 6001 cable
pullers.
Use with other pullers may result in insecure mount-
ing and improper rope alignment.
Failure to observe this warning could result in severe
injury or death.
1st pin
2nd pin
Puller up
against stop

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
8
Setup (cont’d)
Mounting Components
Boom with Nose Unit
• Use only straight 3" diameter rigid steel conduit or
Schedule 40 steel pipe for the boom tubes.
• Do not use boom tubes longer than 3 meters (10').
Longer booms may bend or break.
Failure to observe this warning could result in severe
injury or death.
STRAIGHT EDGE Set up the elbow unit as shown.
Improper setup will cause the elbow
unit to collapse.
Failure to observe this warning could
result in severe injury or death.
Use these boom tubes only:
• boom tubes supplied with the VersiBoom
• 3" rigid steel conduit (3 meters or 10 feet maximum)
• 3" schedule 40 pipe (3 meters or 10 feet maximum)
1. Slide the boom tube into the boom mount until the
tube bottoms out. Sight the tube through the sight
hole to be sure the tube is fully inserted. Tighten the
set screw.
2. Slide the nose unit onto the tube until the tube
bottoms out. Sight the tube through the sight hole
to be sure the tube is fully inserted. Tighten the set
screw.

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
9
Setup (cont’d)
Mounting Components (cont’d)
Booms with Elbow Unit and Nose Unit
• Use only straight 3" diameter rigid steel conduit or
Schedule 40 steel pipe for the boom tubes.
• Do not use boom tubes longer than 3 meters (10').
Longer booms may bend or break.
Failure to observe this warning could result in severe
injury or death.
STRAIGHT EDGE Set up the elbow unit as shown.
Improper setup will cause the elbow
unit to collapse.
Failure to observe this warning could
result in severe injury or death.
Use these boom tubes only:
• boom tubes supplied with the VersiBoom
• 3" rigid steel conduit (3 meters or 10 feet maximum)
• 3" schedule 40 pipe (3 meters or 10 feet maximum)
1. Slide the boom tube into the boom mount until the
tube bottoms out. Sight the tube through the sight
hole to be sure the tube is fully inserted. Tighten the
set screw.
2. Slide the elbow unit onto the tube until the tube
bottoms out. Sight the tube through the sight hole
to be sure the tube is fully inserted. Tighten the set
screw.
3. Adjust the elbow to an appropriate angle and lock
it in place with a pin. Secure the pin with a hitch
pin clip.
4. Slide the boom tube into the elbow unit until the
tube bottoms out. Sight the tube through the sight
hole to be sure the tube is fully inserted. Tighten the
set screw.
5. Slide the nose unit onto the tube until the tube
bottoms out. Sight the tube through the sight hole
to be sure the tube is fully inserted. Tighten the set
screw.
Sight Hole
Sight Hole
Sight Hole

11147 Ultra Tugger®Adapter Package
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
10
Setup (cont’d)
Mounting Components (cont’d)
Slip-in Coupler
Requires: One pin to connect to Nose Unit
1. Select the coupler that best ts the conduit.
2. Slide the coupler into the conduit until the coupler
seats on the end of the conduit.
Note: If the coupler does not seat on the conduit,
see “Straddling the Conduit with a Slip-In Coupler.”
Pull
Conduit
Coupler
Coupler must seat
on the Conduit here
3. Slide the nose unit over the coupler. Align any set of
holes and insert one pin. Secure the pin with a hitch
pin clip.
Note: If possible, add a second pin and hitch pin
clip.
Nose Unit
Coupler
Pin secured with
Hitch Pin Clip
Straddling the Conduit with Slip-in Coupler
Requires: Two pins to connect to Nose Unit
1. Select a coupler at least 25 mm (1") larger than the
conduit.
2. Place the coupler over the conduit.
Note: Do not use this method if the coupler does not
seat on a support structure that can support 35.6 kN
(8000 lb) of force.
Pull
Conduit
Coupler
Conduit must
not protrude
past here
Support
Structure
3. Slide the nose unit over the coupler. Align any two
sets of holes and insert two pins. Secure the pins
with hitch pin clips.
Pull Conduit
Coupler
Conduit must not
protrude past here
Support
Structure