Textron Jacobsen DS312 Supplement

WARNING: If incorrectly used this machine can cause severe injury. Those who use
and maintain this machine should be trained in its proper use, warned of its dangers
and should read the entire manual before attempting to set up, operate, adjust or
service the machine.
ASSEMBLY & OPERATIONS
MANUAL-FRONT MOUNTED
SPRAYER & ADAPTER
4128423 REV A
MODEL:
73-70675 DRIFTLESS SPRAYER DS312

CALIFORNIA
Proposition 65 Warning
Diesel engine exhaust and some of
its constituents are known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Californie Proposition 65
Avertissement
Les échappements des moteurs diesel
et certains de leurs composés sont
reconnus par l’Etat de Californie pour
être cancérigènes, provoquer des
défauts congénitaux et d’autres dangers
en matière de reproduction.
ADVERTENCIA
AVERTISSEMENT
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
California Advertencia
de la Proposicion 65
El estado de California hace saber que
los gases de escape de los motores
diesel y algunos de sus componentes
producen cáncer, defectos de
nacimiento y otros daños en el
proceso de reproducción humana.
L’ é mission du moteur de ce mat é riel
contient des produits chimiques que
l’Etat de Californie consid è re ê tre
canc é rig è nes, provoquer des d é fauts
cong é nitaux et d’autres dangers en
mati è re de reproduction.
El estado de California hace saber
que los gases de escape de este
producto contienen productos
quÍmicos que producen cáncer,
defectos de nacimiento y otros daños
en el proceso de reproducción
humana.
© 2003, TEXTRON INC

1
DRIFTLESS
SPRAYER
IMPORTANTMESSAGE
Thank you for purchasing this Jacobsen product. You have purchased a world class product, one of the best
designed and built anywhere.
This product comes with an Owner/Operator's Manual. The useful life and good service you receive from this
product depends to a large extent on how well you read and understand this manual. Treat this product properly
and adjust it as instructed, and it will give you many years of reliable service.
See a Jacobsen dealer for any service or parts needed. Jacobsen service ensures that you continue to receive
the best results possible from Jacobsen products. You can trust Jacobsen replacement parts because they are
manufactured with the same high precision and quality as the original parts.
Jacobsen designs and builds its equipment to serve many years in a safe and productive manner. For longest
life, use this product only as directed in the manual, keep it in good repair and follow safety warnings and
instructions. You'll always be glad you did.
Jacobsen, a Textron Company
One Bob Cat Lane
Johnson Creek, WI 53038-0469
1-2004
TABLE OF CONTENTS FIGURES PAGE
SAFETY ......................................................................................................................................................... 2
GENERAL SPRAYING INFORMATION ..................................................................................................... 3, 4
GENERAL MAINTENANCE ........................................................................................................................... 5
ASSEMBLY ................................................................................................................................................. 6-9
OPERATION ................................................................................................................................................ 10
PARTS SECTION .........................................................................................................................................11
CASTER FRAME PARTS .................................. FIGURE 1 ................................................................. 12, 13
WING FRAME PARTS ....................................... FIGURE 2 ................................................................. 14, 15
ELECTRICAL..................................................... FIGURE 3 ................................................................. 16, 17
PLUMBING ........................................................ FIGURE 4 ................................................................. 18, 19
ASSEMBLY-FM MOUNT .................................... FIGURE 5 ................................................................. 20, 21
INSTALLATION SHEET ..................................... FIGURE 6 ................................................................. 22, 23
CASTER WHEEL ASSEMBLY ........................... FIGURE 7 ................................................................. 24, 25
NOZZLE BODIES .............................................. FIGURE 8 ....................................................................... 26

2
DRIFTLESS
SPRAYER
SAFETY
GENERALSAFETY
Many people die or suffer serious injury in job related accidents every year due to carelessness. Know
your machinery and be aware of potential hazards. Put safety first in all your operations.
Review all instructions and procedures outlined in this manual annually. Every operator must familiarize
themselves with the operating instructions of the sprayer.
Operational Safety
• Shut down sprayer and power unit and wait for all parts to stop before adjusting, cleaning, or
lubricating the power unit or sprayer.
• Before spraying a field, familiarize yourself with any rocks, debris, trees, ditches or gullies that may be
potentially dangerous. Plan the spraying route to avoid these hazards. When spraying, use individual
section controls to reduce the amount of double spraying.
• Keep sprayer boom width in mind at all times. When turning, exercise caution and avoid any
obstacles or other persons.
Assembly Safety
• Clear large area to fold booms out in field position.
• A minimum of two people should be available for assembly of large equipment, especially when lifting
or exertion is required.
• Always use clean tools of the proper size and specification to match the hardware and specific job.
Transport Safety
• Never transport sprayers with castor wheels on the ground faster than 16 km/h (10 mph).
• Reduce speed on rough terrain.
• For all sprayers ensure that booms are folded and/or locked securely for transport.
Minimize Chemical Drift
The Windfoil sprayer has been designed in wind tunnels to control air flow around and behind the
sprayer to minimize drift, allowing safe spraying in windy conditions.
Drift can blow off a field after it has been sprayed, especially in high winds. Reasonable caution should be
taken, in order to spray effectively and safely.
For maximum drift control, keep curtain in contact with the canopy to ensure a seal to it. Drift
control of the Windfoil is less effective when the wind blows the curtain off the turf canopy,
breaking the seal between the curtain and the turf.

3
DRIFTLESS
SPRAYER GENERAL SPRAYING INFORMATION
Application Tips
Always use clean, filtered water in the sprayer tank.
Check the flow rate from all nozzles using the capacity calibration technique. See Calibration section for
tables and instructions. Adjust the sprayer pressure to get the proper flow rate.
Wilger Hose Connector Bodies
Diaphragm check valves close at 15 psi to prevent excessive dripping.
Table 1: Application rate for Spraying Systems TP Nozzle at 10 inch spacing
Calibration
As a tip wears, the spray pattern distorts, output volumes usually increase, and the droplet characteristics
change. Recalibration may correct for output changes, but cannot correct for spray pattern changes or
the drop size generated. To calibrate and operate the sprayer at the desired pressure. Collect the output
from each nozzle for 60 seconds, using an accurate measuring cup. Record the output from each nozzle.
Replace nozzles that are more than 5% above or below the average reading, or have a visibly distorted
pattern.
Actual sprayer speed, as determined from the following tables, will differ from the sprayer speedometer
readings because of wheel slippage. Run a speed test in the field to be sprayed, and have the sprayer
tank half full. The sprayer must be at full speed before starting the test run. To determine the speed
discrepancy, mark off a distance as found on one of the tables. Run the power unit over this distance,
carefully noting the speedometer reading and recording the time to cover the distance. The actual speed
traveled can be found for the specific distance and time to travel, using the table.
Liquid Capacity
Press
Number bars
800067 2.07
2.76
4.14
2.07
2.76
4.14
80015 2.07
2.76
4.14
2.07
2.76
4.14
2.07
2.76
4.14
2.07
2.76
4.14
2.07
2.76
4.14
2.07
2.76
4.14
2.07
2.76
4.14
Tip
8001
8002
8003
8004
8005
8006
8008
U.S. GALLONS PER ACRE U.S. GALLONS/1000 SQ. FT.
Press 1 nozzle 2.5 3 4 5 7 2.5 3 4 5 7
psi gpm mph mph mph mph mph mph mph mph mph mph
30 0.06 14.3 11.9 8.9 7.1 5.1 0.33 0.27 0.20 0.16 0.12
40 0.07 15.9 13.3 9.9 8.0 5.7 0.37 0.30 0.23 0.18 0.13
60 0.08 19.0 15.8 11.9 9.5 6.8 0.44 0.36 0.27 0.22 0.16
30 0.09 21.4 17.8 13.4 10.7 7.6 0.49 0.41 0.31 0.25 0.18
40 0.10 23.8 19.8 14.9 11.9 8.5 0.55 0.45 0.34 0.27 0.19
60 0.12 28.5 23.8 17.8 14.3 10.2 0.65 0.55 0.41 0.33 0.23
30 0.13 30.9 25.7 19.3 15.4 11.0 0.71 0.59 0.44 0.35 0.25
40 0.15 35.6 29.7 22.3 17.8 12.7 0.82 0.68 0.51 0.41 0.29
60 0.18 42.8 35.6 26.7 21.4 15.3 0.98 0.82 0.61 0.49 0.35
30 0.17 40.4 33.7 25.2 20.2 14.4 0.93 0.77 0.58 0.46 0.33
40 0.20 47.5 39.6 29.7 23.8 17.0 1.09 0.91 0.68 0.55 0.39
60 0.25 59.4 49.5 37.1 29.7 21.2 1.36 1.14 0.85 0.68 0.49
30 0.26 61.8 51.5 38.6 30.9 22.1 1.42 1.18 0.89 0.71 0.51
40 0.30 71.3 59.4 44.6 35.6 25.5 1.64 1.36 1.02 0.82 0.58
60 0.37 87.9 73.3 54.9 44.0 31.4 2.02 1.68 1.26 1.01 0.72
30 0.35 83.2 69.3 52.0 41.6 29.7 1.91 1.59 1.19 0.95 0.68
40 0.40 95.0 79.2 59.4 47.5 33.9 2.18 1.82 1.36 1.09 0.78
60 0.49 116 97 73 58 42 2.67 2.23 1.67 1.34 0.95
30 0.43 102 85 64 51 36 2.35 1.95 1.47 1.17 0.84
40 0.50 119 99 74 59 42 2.73 2.27 1.70 1.36 0.97
60 0.61 145 121 91 72 52 3.33 2.77 2.08 1.66 1.19
30 0.52 124 103 77 62 44 2.84 2.36 1.77 1.42 1.01
40 0.60 143 119 89 71 51 3.27 2.73 2.05 1.64 1.17
60 0.74 176 147 110 88 63 4.04 3.36 2.52 2.02 1.44
30 0.69 164 137 102 82 59 3.76 3.14 2.35 1.88 1.34
40 0.80 190 158 119 95 68 4.36 3.64 2.73 2.18 1.56
60 0.98 233 194 146 116 83 5.35 4.45 3.34 2.67 1.91

4
DRIFTLESS
SPRAYER
GENERAL SPRAYING INFORMATION
After the nozzles have been individually checked and matched, the sprayer should be calibrated to
determine the correct speed for the desired application volume. Refer to Table 1, for typical application
rates for different nozzles. Note nozzles listed are Spraying Systems nozzles.
Note: Tip pressure is usually less than the pressure at the pump. Losses occur in valves, hoses, etc.
Always check the flow by the above calibration method.
Table 2: Time in Seconds to Travel Distance of: Table 3: Time in Seconds to Travel a Distance of:
mph 10
(ft) 25 (ft) 50 (ft) 100 (ft) 200 (ft)
1
1.5
2
2.5
3
4
5
6.8 17.0 34.1 68.2 136
4.5 11.4 22.7 45.5 90.9
3.4 8.5 17.0 34.1 68.2
2.7 6.8 13.6 27.3 54.5
2.3 5.7 11.4 22.7 45.5
1.7 4.3 8.5 17.0 34.1
1.4 3.4 6.8 13.6 27.3
6 1.1 2.8 5.7 11.4 22.7
mph 10
(m) 25 (m) 50 (m) 100 (m) 200 (m)
1 36.0 90.0 180 360 720
1.5 24.0 60.0 120 240 480
2 18.0 45.0 90.0 180 360
2.5 14.4 36.0 72.0 144 288
3 12.0 30.0 60.0 120 240
4 9.0 22.5 45.0 90.0 180
5 7.2 18.0 36.0 72.0 144
6 6.0 15.0 30.0 60.0 120

5
DRIFTLESS
SPRAYER GENERAL MAINTENANCE
Cleaning
Sprayers need to be cleaned to prevent corrosion, cross contamination of chemicals and crop injury.
Trace amounts of one chemical can react with another or carry over to the next spraying and cause crop
damage, especially with pesticides. Long exposures with even small amounts of some chemicals can
damage sprayer components either by corrosion or deposits of gums, etc. If you spray crops that are very
susceptible to injury from the last chemical used, such as vegetables, turf, and ornamentals clean the unit
especially well.
Always try to end the day with an empty tank; avoid contamination of water supplies and injury to plants
or animals. Do not make puddles that might be accessible to children, pets, farm animals, or wildlife.
Flush with clean water, preferably after each day’s operation. However, if you plan to use the same
material over several days, most chemicals may be kept in the tank overnight; the label usually indicates
which may not. Rinse the outside of the sprayer. Surfactants combined with chemicals, when they are
compatible, will provide some cleaning action in the sprayer. Spray the rinse over the application area.
Some chemical combinations (especially if oil is used) may produce a putty type paste (buttering out) in
the sprayer tank and components; flushing with water after each load may prevent an accumulation. If
water alone does not dissolve and remove the buildup, add a low flammable solvent. Allow paste to
dissolve, then agitate and flush. Flush with detergent and finally with clean water. Check with your
chemical agent.
Whenever pesticides are changed, or before sprayer storage, clean sprayers thoroughly with a cleaning
solution. The solution used depends on the chemical to be removed from the sprayer. Check the
chemical label for cleaning instructions.
First, flush with water, then add the cleaning solution to the tank and thoroughly agitate before flushing.
Always flush with clean water to remove the cleaning solution. Remove nozzle tips and screens; clean
them in a strong detergent solution or kerosene, using a soft brush such as an old toothbrush. Never use
a metal probe to clean the orifice of a spray tip!
Follow the same safety precautions during cleaning as for applications. Use respirator, rubber gloves, or
other protective gear as may be directed by label instructions.
Sunshine
Many plastic sprayer parts are degraded by ultra violet light, especially the nozzle flow indicators. Store
the sprayer in the shade to extend the length of service.
Winterizing
After the sprayer is thoroughly cleaned, put 2 to 5 gallons of rust inhibitor or antifreeze in the tank prior to
the final flushing to help prevent corrosion. As the water is pumped from the sprayer, the antifreeze will
leave a protective coating on the inside of the tank, pump, and plumbing. Remove nozzle tips, screens
and no drip valves and store them in a can of light oil such as diesel fuel or kerosene to prevent
corrosion. Close nozzle openings with tape to prevent dirt, insects, mice, or other contaminants from
entering.
During the final cleaning, completely check the sprayer. Look at the hoses, clamps, connections, nozzle
tips, and screens for needed replacements. Store the sprayer in a reasonably clean and dry building.

6
DRIFTLESS
SPRAYER
ASSEMBLY
Description of Parts
Throughout this manual, parts or assemblies that perform a specific function carry an identifying name.
The following lists names used in this manual, along with a description of their appearance and function.
For further detail please refer to the general and plumbing assemblies located in the appendix.
Airfoil: The white plastic piece mounted above the spray boom that runs the entire length of the boom.
The airfoil stabilizes air flow over the spray boom.
Shroud:The large plastic body covering the sprayer. This enclosure houses the air cavity in which the
actual spraying is accomplished.
Curtain:The curtain is composed of fabric hanging down from the shroud edge. The curtain seals the air
inside the shroud.
Wing: The movable ends of the boom. The wing section breaks away from the center boom section
when the spray boom hits a large object. The wings break away to protect the object being
contacted, and the sprayer itself.
Center Frame:
The Center Frame supports the solution tank, supply pump, line strainer. The FM3500ST model
also includes the wing breakaway mechanisms and lift supports. The Center Frame attaches to
each spray boom section via float mechanisms.
Mount Adapter:
Adapts the Center Frame to fit your specific power unit.
First Checks
Your Front Mounted sprayer comes complete in one crate. The crate should include the following items:
1. Center spray section
2. Left and Right wing spray boom sections
3. Center castor frame
4. Center frame
5. Two Castor Wheel Assemblies
6. Assorted parts bag
7. Mount adapter
Look for the factory packing list attached to the shipping crate. Double check that this list has been
completely filled out and that you have all the items indicated by the list. If there are any problems
encountered please contact your dealer or the factory via the number indicated on the packing list.

7
DRIFTLESS
SPRAYER ASSEMBLY
Mount Adapter Attachment
Remove the Mount Adapter and associated hardware from the crate. Refer to Mount Adapter Drawing
(#12285) in the Appendix for help in identifying these parts.
1. Remove appropriate accessories from your power unit to allow your Rogers mount adapter to be
attached.
2. Refer to Specific Mount Adapter instructions for directions.
3. Refer to Mount Adapter drawing for proper orientation of Mount Adapter and attaching hardware.
4. Attach Mount Adapter to power unit.
5. Double check installation to ensure all connections are solid and that any float mechanisms are free
to operate through the entire operating range.
Tank and Boom Pull Attachment
1. Using the 1½” square u-bolts supplied attach the tank mount to the back of the 1½” tubing farthest
away from the power unit with the tank numbers facing away from the power unit. Attach the ¾”
hose with the supplied gear clamp.
2. Using the 1½” square u-bolts supplied attach the boom pull upright tubes on the appropriate sides
(refer to part 48 on drawing 12686).
3. On the right boom pull upright tube attach the eyebolt with two pulleys using the ¼” nut supplied in
the parts bag. On the left boom pull upright tube attach the eyebolt with one pulley.
4. The boom pull upright tubes contain the stand legs and a d-ring necessary for storage purposes.
Center Frame Attachment
1. Remove Center Frame from crate.
2. Place Center Frame in front of Mount Adapter. The pump and line strainer face away from the power
unit.
3. The Center Frame attaches to the Mount Adapter with 1 1/2" square U-bolts and 3/8" nylock nuts.
Refer to Mount Adapter drawing where appropriate.
Center Caster Frame Attachment
1. Remove Center Caster Frame from the crate. The Center Caster Frame includes the center boom
section.
2. Locate the two Caster Wheel Assemblies.
3. Place a Caster Wheel Assembly in each of the wheel bushings of the Center Caster Frame placing
the caster wheel spacers on the top of the bushings. The bushings are located to the extreme left and
right of the front of the Caster Frame.
4. Place the Lynch Pin into end of the caster wheel shaft.
5. Attach the Center Caster Frame to the Center frame via a 1" diameter by 6" long pin. A cotter pin is
provided to hold the 6" long pin in place.

8
DRIFTLESS
SPRAYER
Wing Attachment
1. Place the left and right wings to the sides of the Center Frame. The wheels of the wings will locate to
the outer rear of the sprayer and face toward the power unit.
2. Release the breakaway mechanism of the Center Frame. You may find it beneficial to strike the end
of the Breakaway Arm with a rubber mallet.
3. Loosen the Guide ring that is on the Breakaway Arm.
4. Remove the 1/4" bolts holding the Wing Pivot U-Clamp to the wing.
5. Remove the Wing Pivot U-Clamps from the wing.
6. Place the Wing Pivot U-Clamps onto the Breakaway Arm.
7. Reattach the Wing to the U-Clamps.
8. Ensure that the U-Clamp is pressed up against the inside of the Breakaway Arm.
9. Tighten the 1/4" bolts holding the Wing Pivot U-Clamp to the Breakaway Arm.
10. Lock the Guide Ring into position tight against the Wing Pivot U-Clamp closest to the power unit.
Lock with the Guide Ring set screw.
11. Locate the two ropes and handles. Run the longest rope through the left wing rope cleat and the
shorter rope through the right rope cleat and then both ropes through the half moon ring located on
the Three Valve Mount.
12. Run the longest rope to the right upright tube that has two pulley’s on it and place the rope through
one of the pulleys, then run the rope directly across to the left upright tube, through the pulley and
down to the left wing rope pull tab. Run the shortest rope to the right upright tube, through the pulley
and down to the right wing rope pull tab.
13. Tie a tight knot in the very end of the rope. Pull rope back out of the Rope Tab until the knot is tight
against the Rope Tab.
Plumbing Hookup
1. Locate the Three Valve Mount that holds the On/Off control valves for each spray section and the
pressure regulating valve. Attach the cross plate supplied in the parts bag to the Three Valve Mount
with ¼” square u-bolts. Attach Mount to upright on the Center frame with 1 1/2" square U-bolts.
2. Adjust height of controls to suit your power unit and user preference. Use the supplied tie straps to
secure the hoses in the appropriate place.
3. Attach the Universal Mount Bracket and Nozzle Flow Indicator for the Center Boom Section using the
¼” x 2" lg bolts supplied to the support on the solution tank.
4. Locate the three 1/2" hoses from the Center Boom Section. Cut to desired length and hook the end of
each hose to the hose barbs on the nozzle flow indicator. To avoid confusion, ensure that the position
that each hose exits the shroud of the spray boom corresponds with the position it is installed on the
nozzle flow indicator. Plastic, crimp type hose clamps are located in the parts box.
5. Attach wing supply hoses to the appropriate wings placing the supply hose underneath the
breakaway arm. Attach the center nozzle flow indicator supply hose and also the bypass hose to the
top of the solution tank. Use the plastic crimp type hose clamps to secure to hose barbs.
ASSEMBLY

9
DRIFTLESS
SPRAYER
Electrical Hookup
1. Route electrical harness along power unit frame. Avoid all pivot points and moving parts to avoid
pinching or wearing into cable.
2. Plug cable into auxiliary 12V power outlet on power unit.
3. Tie cable securely to power unit.
4. Clean terminals of battery to ensure good connections.
Last Check
1. Double check all fasteners, nuts and bolts adjusted during installation for tightness.
2. Grease all grease nipples. There are two nipples at each wing pivot, one nipple for the Center Castor
Frame pivot and one nipple for each castor wheel pivot.
3. Operate the front mount sprayer through its entire float range. Check for interference between the
frame, fenders, floor boards and attachments. Check also for pinching of hoses and electrical power
wire for pump.
4. Place water in solution tank. Operate pump and spray through each boom section. Check all
plumbing for any possible leaks.
5. Operate sprayer over concrete pad. Examine spray pattern on concrete to ensure all spray tips are
operating.
ASSEMBLY

10
DRIFTLESS
SPRAYER
OPERATION
First Checks
During sprayer setup, test the operation of the spray tips, hoses and plumbing system with clear water.
Refer to the sprayer maintenance and operation section found in this manual.
Clean sprayer tank and flush plumbing system with clean water.
Check line strainer and nozzle screens for residue and debris. Clean screens with clear water. Replace
any screens that remain clogged after cleaning or are torn.
Check and clean nozzle tips. To ensure best performance calibrate spray tips. Refer to Calibration found
in the General Spraying Information section of this manual. The frequency that you should perform
calibration will vary based on the volume and type of spraying that is done.
Determine proper chemical mixture based on the specific chemical and spray tip size. Different size spray
tips and nozzle screens are available through your Jacobsen dealer.
Using the Sprayer
Prepare to spray by turning on the power switch for the pump. Observe the pressure gauge on the 3
Valve Mount. The pressure should rise slightly above the spray pressure desired for the specific tip type
and chemical. The exact difference between the set pressure with no booms spraying and the spray
pressure will depend on the size of tips and number of spray booms engaged.
Adjust the pressure regulator located on the 3 Valve Mount to obtain the desired pressure.
Begin moving at the desired spray speed.
Turn on the appropriate sections of the spray boom with the specific On/Off valve located on the 3 Valve
Mount.
Boom Operation
If you wish to lift a boom, switch off the pressure to the boom. Wait a couple of seconds so the mist under
the boom can settle before lifting the boom.
Each wing can be lifted with the rope and secured in place by pulling the rope through the cleat on the top
of the 3 valve mount.
To disengage simply lift the rope to pull it out of the cleat. Store the excessive rope with the handle on the
hook.
The wings are attached to your boom via the breakaway pin and pivot. If you strike an object with a wing
that wing should breakaway as a protection against damage.
After striking an object return the wing to position. Grasp boom at outer edge. Move end of boom forward
until Breakaway Pin contacts the breakaway mechanism. With sharp forward motion, lock boom into
Breakaway catch.

11
DRIFTLESS
SPRAYER PARTS SECTION
PARTS
SECTION

12
DRIFTLESS
SPRAYER
CASTER FRAME PARTS
FIGURE 1

13
DRIFTLESS
SPRAYER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
CASTER FRAME PARTS
FIGURE 1
1-1 01395 BOLT-5/16 X 3 1/2 4
1-2 00400 FRAME-CASTER 1
1-3 00972 FITTING 5
1-4 00921 CASTER WHL ASSY 2
1-5 01499 AIRFOIL 1
1-6 01397 DECAL 3
1-7 01154 BOLT-1/4 X 3/4 2
1-8 01157 WASHER-FLAT 14
1-9 00968 NUT-1/4 36
1-10 01396 DECAL 6
1-11 00721L AIRFOIL STANDOFF 4
00721R AIRFOIL STANDOFF 4
1-12 01153 NUT-#10 10
1-13 01152 SCREW-#10-24 X 3/4 10
1-14 01502 SHROUD 1
1-15 00969 NUT-5/16 6
1-16 12653 FLAT-AL,SPAR LP SPRAYER 2
1-17 01387 CURTAIN 1
1-18 01385 CURTAIN-HANGER 1
1-19 00805 COLLAR 2
1-20 01156 Scr, TEK, #12 x 1 1/4 14
1-21 01070 BOLT-1/4 X 2 4
1-22 00961 PLUG-TUBE 2
1-23 01073 SCREW-SET 2
1-24 00954 BOLT-3/8 X 7 2
1-25 00966 BOLT-1/4 X 2-1/2 8
1-26 00814 BREAKAWAY CATCH 2
1-27 00955 SPRING 2
1-28 00956 NUT-3/8 30
1-29 12272 SCREW-1/4 X 1-1/4 4
1-30 00130 BUSHING 4
1-31 00804 PIN-1 X 6 3
1-32 00470 BREAKAWAY ARM 2
1-33 12717 LEG-STEINER FM 2
1-34 01319 PIN-1/4 X 2-1/2 2
1-35 00128 BUSHING 4
1-36 06521 BOLT-3/8 X 5 2
1-37 00957 WASHER-FLAT 3/8 8
1-38 00690 SPRING 2
1-39 12713 PL,STL,DBL CROSS,1-1/2 X 11
1-40 12740 MT, 3 VLV / ROPE 1
1-41 01050 UBLT-3/8 X 1-1/2 X 2-1/2 10
1-42 01209 VALVE 1
1-43 01164 BOLT-1/4 X 1 4
1-44 12723 CLEAT-CLAMP 2
1-45 05388 SCREW-#10-24 X 1/2 4
1-46 00425 FRAME-CENTER 1
1-47 01049 UBLT-1/4 X 1 X 2 2
1-48 12683L BOOM-PULL LEFT 1
12683R BOOM-PULL RIGHT 1
1-49 12681 PULLEY 3
1-50 12684 EYEBOLT 2
1-51 01057 PLUG 4
1-52 01398 SERIAL PLATE 1
1-53 01172 CLAMP-SADDLE 1
1-54 12570 TANK 1
1-55 00963 NUT-1/2 2
1-56 05103 STRAP-HOLDER 2
1-57 01701 STRAPPING 1
1-58 12811 ROPE 1
12812 ROPE 1
1-59 06318 HANDLE-PLASTIC 2
1-60 12045 PL,AL,BACKING 1
1-61 01310 TIE 2
1-62 01306 TIE 10
1-63 00965 PIN-3/16 X 1-1/2 3

14
DRIFTLESS
SPRAYER
WING FRAME PARTS
FIGURE 2

15
DRIFTLESS
SPRAYER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
WING FRAME PARTS
FIGURE 2
2-1 01500 AIRFOIL-40" / 50" 2
2-2 01503L SHROUD-LFT 1
01503R SHROUD-RT 1
2-3 01381L FRAME-40" SERIES LFT 1
01381R FRAME-40" SERIES RT 1
2-4 00920 WHL ASSY 2
2-5 12387 BOLT-5/8 X 5 2
2-6 01313 NUT-5/8 2
2-7 01505 CURTAIN 2
2-8 01504 CURTAIN HANGER 2
2-9 00951 U-CLAMP 4
2-10 05447 BOLT-5/16 X 2 2
2-11 06307 ROPE 2
2-12 12057 BACKING-WING 2
2-13 01154 BOLT-1/4 X 3/4 6
2-14 01157 WASHER-FLAT 1/4 2
2-15 00968 NUT-1/4 2
2-16 01396 DECAL 2
2-17 00721L AIRFOIL STANDOFF 4
00721R AIRFOIL STANDOFF 4
2-18 01397 DECAL 3
2-19 01153 NUT-#10 4
2-20 01152 SCREW-#10-24 X 3/4 4
2-21 00966 BOLT-1/4 X 2-1/2 2
2-22 00130 BUSHING 2
2-23 00972 FITTING 2
2-24 01156 Scr, TEK, #12 x 1 1/4 14
2-25 01070 BOLT-1/4 X 2 2

16
DRIFTLESS
SPRAYER
ELECTRICAL
FIGURE 3

17
DRIFTLESS
SPRAYER
ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY
ELECTRICAL
3-1 12724 ELEC CON-MALE 1
3-2 12813 CABLE-14/2 X 60 1
3-3 01216 SEAL 4
3-4 01215 TERMINAL 2
3-5 01274 CONN,WEA-PAK,2M,06L 1
3-6 01276 CONN,WEA-PAK,2F,07L 1
3-7 01219 TERMINAL 1
FIGURE 3

18
DRIFTLESS
SPRAYER
PLUMBING
FIGURE 4