THE SHOWER LAB VIEW 14.2H User manual

Illustration - View 14.2H
Bi-folding Bath Screen
Inward Opening
VIEW 14.2H
07/2019 V 2.2

VIEW 14.2H
IMPORTANT
•This shower screen / enclosure must be installed by suitably qualified individuals. We
recommend a minimum of two people for safe assembly of certain sections of this screen.
•Ensure all appropriate safety equipment, especially protective footwear, safety glasses
and gloves are used.
•When drilling holes in ceramic tiles, use masking tape to prevent the drill from slipping:
DO NOT use hammer action as this will crack the tiles. Use a high quality drill bit to ensure
a clean, precise hole.
Tighten hinges and brackets to the recommended 15.6N.
•
•
Please leave these instructions with the customer following installation.
PRIOR TO INSTALLATION
•Before disposing of the packaging and prior to commencing assembly, please check all
the components to ensure that they have been supplied correctly and are undamaged.
Subsequent claims for missing or damaged pieces will not be accepted once the
packaging has been disposed of and installation commenced.
•In the event of any queries please contact your supplier quoting the relevant model
information.
•The Tray / Tiled floor on which this screen is to be installed must be level on all sides.
•It may be necessary to use alternate fixings to those supplied, depending on the properties
of the walls to be fixed to.
•Use the protective corners supplied at all times until the glass is moved to its final position.
•Ensure that the glass is installed correctly, taking care to avoid installing the glass upside
down. On certain panels an easy clean coating is applied to one side only, this is clearly
marked with a sticker on the non-coated side. The coated surface is to be fitted inwards
towards the inside (wet side) of the screen.
•Ensure that all surfaces to be sealed are clean and dry prior to applying the silicone
sealant. Use a high grade fungal resistant sealant.
•Allow a minimum of 48 hours after application of the silicone sealant prior to using the
screen.
TOOLS & MATERIALS REQUIRED
Junior Hacksaw
Straight Edge (Steel
Rule)
Fine Tooth File
Set or Roofing
Square
Masking Tape
Modelling Knife
Spirit Level
Pencil
Silicone Gun
Power Drill
Ø6mm Masonry Drill Bit
2x Suction Glass Lifters
High Quality Silicone Sealant
Tape Measure
Pozi-drive
Screwdrivers, PZ1&2
Safety Glasses and
Gloves
CARE AND MAINTENANCE
(please ensure that these instructions are left with the installed unit)
•We recommend routine cleaning of your screen / enclosure with hot water using a soft
cloth, then drying with a dry soft cloth or chamois leather.
Ritec Aftercare for Shower Glass is recomended for best results.
•All glass has been treated with EASY CLEAN glass finish and care must be taken to avoid
any abrasive cleaning products that may damage the special surface protection.
•DO NOT use acidic based de-scaler products or products containing bleaches or solvents.
Digital Torque Wrench
07/2019 V 2.2

Supplied Parts
Glass Panel - P
x1
Glass Panel - R
x1
Glass to Wall Hinge
x2
(Option Dependant)
Bath Screen Underframe
x1
Bath Screen End Cap
x1
Glass support
x4
Bottom door seal
x2
Glass to wall seal
x1
180° Magnetic seal
x1
Inward Opening
Outward Opening
Glass to glass hinge
x2
Each hinge includes
3x Screws and Wall Plugs
VIEW 14.2H
07/2019 V 2.2

A
B
I
C
C
H
D
D
F
G
E
G
A
B
I
C
H
D
F
E
G
Glass Panel - P
Glass Panel - R
Glass to Wall Hinge
Bath Screen Underframe
Bath Screen End Cap
Bottom Door Seal
Glass to Wall Seal
180° Magnetic Seal
Glass to Glass Hinge
These instructions are for the bi-folding bath screen. The image below shows an inward opening
conguration.
Please use the below diagram to reference the list of parts.
VIEW 14.2H
07/2019 V 2.2

Please see below the two congurations for this bi-folding bath screen.
Please note the hinge orientation that has been supplied will help determine which
conguration you have.
Inward Opening
Outward Opening
VIEW 14.2H
07/2019 V 2.2

Measure the width of both panels, add
6mm to this measurement.
Mark this length on the under-frame.
For best results, use masking tape. Cut
squarely with a fine toothed junior
hacksaw. Unwrap the tape and remove
any burrs with a fine file, taking care
not to scratch or damage the surface
finish.
Posi�on the under-frame on the edge
of the bath. The under-frame needs to
be set back far enough so that it is on
the level surface.
DO NOT use silicone at this point.
Peel off the backing tape and secure
the under-frame squarely in place with
the self-adhesive pads supplied.
Peel off the backing tape from the
under-frame end cap, insert into the
end of the under-frame and press
down firmly.
Place the glass supports over the
under-frame as indicated.
12
3 4
Inside of shower
01/05
VIEW 14.2H
07/2019 V 2.2

Assemble the two 90° glass to wall
hinges onto the screen, making sure
the hinge is centred in the glass holes.










glass to wall hinges to the wall.



the measurements.





screw the hinges to the wall.
5
7 8
Professional Tip
If drilling ceramic tiles, place
masking tape on the tiles before
marking and drill through the
tape to prevent the drill bit from
skidding.
DO NOT use Hammer Action as
this will break the tiles.
02/05
Wall Plate
always on
inside of
screen
9
Hole “B”
VIEW 14.2H
07/2019 V 2.2
















910
11 12


03/05
VIEW 14.2H
07/2019 V 2.2



























 
 
Trim the aps
Underframe
Bottom
Door
Seal
14mm
Magnestic
Seal
Cut only the aps
Cut
Cut
04/05
VIEW 14.2H
07/2019 V 2.2

Using the sharp modelling knife, trim
any excess gasket material from the
hinges and brackets that may have
squeezed out when �ghtening. Take
care not to scratch the glass.
Fit the cover plates to the 90° glass to
wall hinges and glass to glass hinges.
17 18
Apply silicone sealant as hown below
between the under-frame and the bath
tub. Both inside and out.
19
Trim
Silicone Silicone
Silicone
05/05
VIEW 14.2H
07/2019 V 2.2

Glass to Wall Hinge Template
Please use this template to locate Hole “B” if your screen opens OUTWARDS from the wall.
Tear Here
Tear Here
40mm
70mm
27mm
15mm
Hole “B”
VIEW 14.2H
07/2019 V 2.2