Elite Screens Sable Frame B2 Series User manual

JA12142021 www.elitescreens.com U-00199 1
Sable Frame B2 Series
Matte White Fixed Frame Screen
FeaturingCineWhite®UHD-B
USER’S GUIDE – M Type
V 2.1
__________________________________________________________________________________________
Congratulations on your new Sable Frame B2 purchase! The material included is our ISF Certified
CineWhite® UHD-B which produces accurate colors in a light controlled environment as the director intended.
In order for the CineWhite® UHD-B to maintain its projection qualities and optimum performance
please refer to the list below for proper maintenance and cleaning.
•Use a dry microfiber cloth to remove dust from the screen’s surface.
•When cleaning, use a damp microfiber cloth with warm water to remove anymarks.
•Never rub or apply pressure when cleaning the surface.
•Never attempt to use any solutions, chemicals, or abrasive cleaners on the screen surface.
•To avoid damaging the screen, avoid touching it directly with your fingers, pens/pencils or any other
sharp or abrasive objects.

JA12142021 www.elitescreens.com U-00199 2
Frame Parts List
A. Vertical Frame x 2pcs
B. ½ Horizontal Frame x2 pcs
C. ½ Horizontal Frame x 2 pcs
Hardware Parts List
a. M4*4
b. D5*4
c. M4*4
d. D5*4
g.
h.
i.
j.
k.
l.
o.
p.
r.
Item
Parts List
92”
100”
110”
120”
135”
150”
165”
180”
200”
a.
Center Joints- M4 (bottom position)
2
2
2
2
2
2
2
2
2
b.
Center Joints-D5 (top position)
2
2
2
2
2
2
2
2
2
c.
Elbow Joints M4 (bottom position)
4
4
4
4
4
4
4
4
4
d.
Elbow Joints D5 (top position)
4
4
4
4
4
4
4
4
4
g.
M4x7 Screws
24
24
24
24
24
24
24
24
24
h.
Spring
56
60
66
72
80
88
100
106
116
i.
Pull Hook
2
2
2
2
2
2
2
2
2
j.
Wall brackets
4
4
4
4
4
4
6
6
6
k.
Wall Screws M5x50
8
8
8
8
8
8
12
12
12
l.
Hollow Wall anchors
8
8
8
8
8
8
12
12
12
o.
Center Support Bar
1
1
1
1
1
1
2
2
2
p.
White gloves
2
2
2
2
2
2
2
2
2
r.
Φ3 mm Long Iron (sides) rod /
Short rod (top/bottom)
2/4
2/4
2/4
2/4
2/4
2/4
2/4
2/4
2/4
C+B
B+C
A
A
Red
Black

JA12142021 www.elitescreens.com U-00199 3
Frame Assembly
Step 1: Place the EPE sponge (foam) sheet on the ground of the area where the screen will be assembled.
Step 2: Position the pieces of the frame on the EPE sponge in the arrangement shown below.
Step 3: Insert center joint (a/b) connectors into one-half of the horizontal frame (B/C) and secure with the
M4x7 screws (g) as shown in the illustration below.
Tip: The center joint (b) with the larger diameter holes should be on top.
Step 4: Connect the elbow joints (c/d) to the top and bottom sections of the vertical frame. Once inserted,
connect the vertical sections to the horizontal frame sections. Make sure all holes are in alignment and the frame
pieces are flush (no gaps). They should form perfect right angles.
Tip: The elbow joint (d)with the larger diameter holes should be on top.
8.
a.
b.
d.
c.

JA12142021 www.elitescreens.com U-00199 4
Step 5. Secure the elbow joints by fastening them with M4x7 screws (g), 4 at each corner.
Screen Material
Step 6: Put on the white gloves (p) and carefully unroll the screen material on a clean surface from the roller to
the other side as shown below. The back side of the screen material should be placed upwards. Then place a
bottom grommet (r) on the screen material’s eyelet and snap in the top grommet (s) as shown below.
Repeat the process for all eyelets.
Step7: Carefully place the screen on top of the assembled frame as shown below.Make sure that the angular
edges of the frame are not allowed to come into direct contact with the screen material to avoid puncturing.
Front

JA12142021 www.elitescreens.com U-00199 5
c
c
c
c
c
c
c
c
c
c
Step 8: Insert the rods (r) through the sleeves according to their corresponding lengths on each edge of the
screen as shown below. The short rods (top/bottom) will overlap to secure a firm grasp in the middle areas.
How to attach the springs
Step 9: Hook one end of the spring and secure inside the groove of the frame, use the spring hook (i)to attach
the spring to the hole located on the screen material’s outer edge in the following order.
Back Side
r. (Red tips)
Back Side
r. (Black tips)
Back Side
Back
Side
Go through the hole
from bottom to top
h.
i.
Spring must hook both
overlapping
short rods.
c
c

JA12142021 www.elitescreens.com U-00199 6
First connect on four corners, steps 1-4. make sure all four corners are fixed before proceeding with next spring.
Continue to attach the remaining springs to the material in steps 5-12 in the follow order.
1
2
4
3
5
6
7
8
9
10
11
12

JA12142021 www.elitescreens.com U-00199 7
Step 10: Insert the Center Support Bar (o) into the upper top groove on the back of the frame with the bottom end
near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in
alignment with the groove.
Installation
Step 11: Measure the overall length and height of the frame and drill holes for the top brackets. Line up the wall
brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. If not
installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50 wood screws with a
screwdriver. Make sure the brackets are leveled.
Model/Size
X = Wall bracket distance
X1 = Bracket hole distance
Y = Top/Bottom Wall Bracket Height
92”
1100mm (43.30”)
30mm (1.18”)
1180mm (46.46”)
100”
1170mm (46.06”)
30mm (1.18”)
1280mm (50.39”)
110”
1280mm (50.39”)
30mm (1.18”)
1410mm (55.51”)
120”
1390mm (54.72”)
30mm (1.18”)
1530mm (60.24”)
135”
1550mm (61.02”)
30mm (1.18”)
1720mm (67.72”)
150”
1720mm (67.72”)
30mm (1.18”)
1900mm (74.80”)
Diagonal Models 150” and
below use 1 x Center Support
Bar
Diagonal Models above 150”
require 2 x Center Support Bars
Place a center support
bar 30 cm (11.8”) apart
from the center (red
line).
Don’t lock the screw to the bottom.
j.
k.
Diagonal Sizes of 150” and below use 4 x wall brackets

JA12142021 www.elitescreens.com U-00199 8
Step 12: Position the fixed frame screen onto the top wall brackets (fig 1) as shown below and push down at the
center of the top of the frame (fig 2) to secure.
For Technical Support or an Elite Screens contact in your area,
visit www.elitescreens.com
Model/Size
X = Wall bracket distance
X1 = Bracket hole distance
Y = Top/Bottom Wall Bracket Height
165”
940mm(37.01”)
30mm (1.18”)
2090mm(82.28”)
180”
1030mm (40.55”)
30mm (1.18”)
2280mm (89.76”)
200”
1140mm (44.88”)
30mm (1.18”)
2530mm (99.61”)
Don’t lock the screw to the bottom.
Diagonal Models above 150” require 6 x wall brackets
c
c
1.
2.