The Splash Lab TSL.R.030 Maintenance and service guide

TSL R 030. .
ribbon hand dryer
installation + maintenance

contents
3 Safety and Warnings
4 Box Contents
5 Technical Data
6 BeforeYouInstall
8 HowtoInstall
13 Commissioning
15 Operation
15 Maintenance
16 Cleaning
17 Troubleshooting
18
18
Diagram
Spare Parts / Accessories
19 Warranty
BackCover ContactDetails
2 + TSL.R.030 RIBBON HAND DRYER MANUAL

To reduce the risk of fire, electric shock or injury to persons, observe the following:
+ Use this unit only in the manner intended by the manufacturer. If you have any
questions contactthemanufacturer(seebackpagefordetails).,
+ This equipment should be installed in a way that ensures all electrical parts are
keptdry.
+ A means of electrical isolation must be incorporated in the fixed wiring, in
accordancewiththecurrentlocalregulationsinforce.
+ Disconnectthepowersupplybeforeperforminganymaintenanceontheproduct.
+ Childrenshouldnotplaywiththisequipment.Cleaningandmaintenanceshallnot
beperformedbychildrenwithoutsupervision.
+ Thisequipmentisdesignedtobeusedincommercialandpublicareas;itisnot
intendedfordomesticorresidentialuse.
+ Replacefuseonlywiththesametypeandratingoffuse.
+ Ensurewiringandcoverisinstalledcorrectlybeforeconnectingtolivepower
supply.
+ Ifindoubt consultanelectrician.,
+ Thisproductisnotintendedforuseinadomesticorresidentialapplication.
+ Thedryermustbeinstalledinaccordancewiththeelectricalinstallation
regulationsinforceatthetimeofinstallation.
+ Thehanddryermustbegrounded.
Read and save these instructions
WARNING !
TSL.R.030 RIBBON HAND DRYER MANUAL + 3
General information
310 410 5008
Technical support
[e-mail]
For further contact information visit:
www.thesplashlabusa.com
Warehouse + Offices:
20809 Higgins Court, Torrance CA 90501
Showroom:
8745 Washington Boulevard, Studio D, Culver City CA 90232
TSL.R.030 ribbon hand dryer

A Dryerheadassembly
B Hand dryer motor unit
C Power cable
D Anti-rotation collar (already installed)
E Gasket (already installed)
F Anti-rotation washer
G Fixing nut
H Motor mounting screws
I Hex wrench
J Air hose
boxcontents
A
C
B
I
H
D
E
F
G
J
4 + TSL.R.030 RIBBON HAND DRYER MANUAL

Current 7.6-8.4A; 3.8-4.2A
Powerconsumption 0.84-1.0kW
Standbypower 0.3-0.4kW
Dryingtime <15seconds
Weight 17lb13oz (8.0kg)
Material AISI304stainlesssteel
Noiselevels 70.6dB
Heatingelement 500W
Motortype Brushtype;dualballbearings;
Motorpower 500 - 350W
Airspeed 367ft/s
Airflow 25.3cuft/min
Sensorrange 5"+/-1"
Securitycut-of f time 60seconds
Motorthermalprotection Autoresettingthermostatsetat203°F
Heaterthermalprotection Autoresettingthermostatsetat185°F
Thermalcutoutfusesetto288°F
Insulation Class1
IPrating IP35
Approvals CE UL cUL, RoHS, ADA,,
technical data
Finishes TSL.R.030.C.E120.H Bright Polished
TSL.R.030.CS.E120.H Brushed Stainless
TSL.R.030.CP.E120.H Brushed Copper
TSL.R.030.BK.E120.H Brushed Black
TSL.R.030.BR.E120.H Brushed Brass
Voltage 110-120V ac, 60Hz; 220-240V ac, 50Hz
TSL.R.030 RIBBON HAND DRYER MANUAL + 5
Warranty1 year parts and labor
Filter 3M filter assembly (HEPA filter is available for this
product, please enquire for technical information)

Ribbonhanddryersaresuppliedwith
47-1/4 offlexiblehose,sothe" (1200mm)
dryermotorunit mustbefittedwithin
47-1/4 oftheheadunit, to" (1200mm)
ensurethatthemotorair-outlethead
canbeconnected.
Basins
Use of a The Splash Lab Monolith basin
isrecommendedforusewiththeRibbon
rangeofproducts. Ifanalternativebasin
isused, then appropriatemountingpoints
must becreatedinbasinorcountertopto
accommodatetheRibbonproducts.
Powersupply
A15Afusedsupplymustbeprovidedfor
connectiontothemainspowersupply.
Spacing
If the Ribbon Hand Dryer is installed with
other units from the Ribbon range, the
Ribbon Faucet, which is at the center, should
be 8" (200mm)to the left of the Hand Dryer.
The Ribbon Soap Dispenser should be
6" (152mm)to the left of the Faucet.
Location
before you install
Disclaimer:Circuitsshouldonlyuse
80%oftheirgivenamperagetoprevent
overloads.ThestandardUS120V15Amp
circuitshouldonlyuseupto12ofits15
amps, 220V8Amp circuitshouldonlyuse
upto4ofits8 amps.
6 + TSL.R.030 RIBBON HAND DRYER MANUAL
8"
(200mm)
Back wall
Fixture insert
Washbasin
Top view
Ø" 1-3/8 (35mm)
Soap Faucet Dryer
6"
(152mm)
2"
(50mm)

SIDEFRONT
THROUGH HOLE
Default
Sensor
Range
3-15/16 - 5-1/8" "
(100-130mm)
Ø 1 3/8" (35mm)
2-1/4"
(57.2mm)
Ø 1-1/4" (32mm)
2-23/32" (69mm)
10-3/4" (270mm)
12-1/16" (306mm)
7-9/16" (193mm)
9-1/16"
(230mm)
7-11/16"
(195.3mm)
5-3/4" (146mm)
6-5/8"
(168.4mm)
5-7/8" (148.5mm)
110-120V / 15A plug
220-240V / 8A plug
before you install
TSL.R.030 RIBBON HAND DRYER MANUAL + 7
51-3/16" (1300mm)
47-1/4" (1200mm)
/"3 8 (9.5mm)MIN
- / "1 3 8 (35mm)MAX

1
Drill hole 1 3/8 diameter in " (35mm)
counter-top, if not already cut.
2
Fit anti-rotation washer from below basin.
how to install
8 + TSL.R.030 RIBBON HAND DRYER MANUAL

Fix fixing nut, and secure using wrench. Remove cover-fixing screws from
underside of dryer motor using the
security hex key provided, and then
remove the cover.
3 4
TSL.R.030 RIBBON HAND DRYER MANUAL + 9

how to install
Fit the dryer motor unit to wall or cabinet,
within 47-1/4 of the dryer " (1200mm)
nozzle already installed on the basin /
countertop.
Thread the power cable through the
knockout in the back or base of the dryer
and feed to connector block. Connect
the cables as marked on the dryer unit.
(Cable supplied pre-fitted)
5 6
10 + TSL.R.030 RIBBON HAND DRYER MANUAL

7 8
Thread the sensor and ground cables
through the air-hose.
Feed cables into air outlet nozzle and
then through cable exit grommet.
TSL.R.030 RIBBON HAND DRYER MANUAL + 11

9 10
Connect the sensor cable to the 6-pin
fitting on the PCB control, and the
ground cable to the corresponding earth
connector in the dryer motor unit.
Connect air hose onto outlet nozzle on
dryer motor and tighten hose clamp.
how to install
12 + TSL.R.030 RIBBON HAND DRYER MANUAL

11
Re-fit the dryer cover and tighten the
fixing screws.
TSL.R.030 RIBBON HAND DRYER MANUAL + 13

Turn on the power supply to the dryer, and then test that the dryer will operate when
the user’s hands are placed within the detection range.
The motor speed and sensor range can be adjusted to suit user preference and the
environment, if required. The heater element can also be switched of f if desired.
Warm air speed adjustment
1.Switch of f the power, loosen the cover
screws and remove the cover.
2.Use small Phillips head screwdriver
to turn variable resistor shaft. Turn
clockwise to increase the motor
speed; turn counter-clockwise
to reduce the motor speed.
Sensor range adjustment
1.Switch of f the power, loosen the cover
screws and remove the cover.
2.Use small Phillips head screwdriver
to adjust the variable resistor. Turn
clockwise to increase the sensitivity;
turn counter--clockwise to reduce
the range.
commissioning
14 + TSL.R.030 RIBBON HAND DRYER MANUAL

1. Switch of f the power, loosen the
cover screws and remove the cover.
2. Adjust the heater switch on the
PCB with a small plastic or wood
flat blade probe.
2-1 Slide the switch to ‘ON’:
Enables heater
2-2 Slide the switch to ‘1’:
Disables heater
Heater Element Switch ON/OFF
TSL.R.030 RIBBON HAND DRYER MANUAL + 15

+ The user is to shake excess water of f their hands.
+ The user then places their hands within the detection range of the sensor to
activatethehand dryer.
+ The motor will start and air is blown onto the user’s hands.
+ The motor will stop when the user’s hands are removed from the detection range.
maintenance
The hand dryer should be serviced on a regular basis to ensure long service life of
the unit.
+ Isolate the unit from the power supply before any servicing or maintenance work is
carried out.
+ Remove the cover by unscrewing the fixing screws on the underside of the cover.
+ Remove any dust or foreign body from the air intake and (both inside and outside
the dryer). Where necessary, use a brush or vacuum cleaner.
operation
16 + TSL.R.030 RIBBON HAND DRYER MANUAL
+

TSL.R.030 RIBBON HAND DRYER MANUAL + 17
All grades of stainless steel will stain or discolor if due care and attention is not
taken. The surface must be regularly cleaned to ensure a long service life of the
hand dryer.
Use a soft cloth or sponge with a mild solution of soapy water as part of the regular
washroom janitorial routine. Do not use abrasive or cream cleaners as these will
damage the surface finish.
If the hand dryer is subjected to a highly chlorinated environment e.g. swimming
pools or marine coastal locations, a further treatment, in addition to the regular
cleaning as described above, is recommended to use a household cleaning product
containing silicone.
If further information is required, contact The Splash Lab Team for more detailed
stainless-steel care guidelines. 
cleaning
+
+
+
+

If the dryer will not run:
+ First ensure that the breaker supplying the dryer is operational. If it is, disconnect
the power and remove the dryer cover. Taking suitable precautions to avoid shock
hazard, reconnect the power and check for voltage at the terminal block. Verify
that connections are made correctly.
The dryer cycles by itself or runs constantly:
+ Ensure that there is no obstruction on or in front of the IR sensor. Clean any dirt or
debris of f the sensor lens. If problem persists, replace sensor.
The dryer makes a loud noise and does not run for a complete cycle:
+ Ensure that the supply voltage is correct. Dryer will make a loud humming noise
if the input voltage is too high. Verify voltage requirement on unit rating label and
correct supply as required. (If circuit board module has been damaged, replace it
and the infra-red sensor module.)
The dryer runs but air stream is low pressure and/or low velocity:
+ Ensure that the supply voltage is correct. Dryer will run weakly if the input voltage
is too low. Verify voltage requirement on unit rating label and correct supply as
required.
initial installation
troubleshooting
18 + TSL.R.030 RIBBON HAND DRYER MANUAL

If the dryer will not run:
+ First ensure that the breaker supplying the dryer is operational. If it is, disconnect
the power and remove the dryer cover. Replace the CBM and IR sensor module.
Taking suitable precautions to avoid shock hazard, reconnect the power and
check for Voltage at the terminal block.
The IR sensor only sees close range objects:
+ Ensure that there is no obstruction on or in front of the IR sensor. Clean any dirt
or debris off the sensor lens. Check variable resistor for sensor range setting. If
problem persists, disconnect the power and remove the dryer cover and replace
CBM, IR sensor module.
The heater gets hot but no air stream is produced:
+ Disconnect the power. Remove the dryer cover. Check variable resistor for speed
setting. Disassemble the blower- motor/ fan housing. Replace the fan motor.
Reassemble.
in-service failure
troubleshooting
TSL.R.030 RIBBON HAND DRYER MANUAL + 19

The dryer only blows cold air during a full cycle:
+ Disconnect the power. Remove the dryer cove and check/ ensure heater switch
is ON. Disassemble the blower- motor/ fan housing. Test the thermostat for open
circuit. Check the heater element for signs of burning or breakage. Damaged
element must be replaced.
The air stream is low pressure and velocity:
+ Check the output nozzle for obstructions, If none are present, disconnect the
power. Remove the dryer cover. Remove any dust/lint buildup from intake vent
slots. Check VR for speed setting. Disassemble the blower / motor / fan housing.
Check motor brushes for wear; if less than 1 1/4" is remaining. Replace brushes.
We are always looking to improve. If these steps
did not solve your problem please contact us
and we will endeavor to help.
Tel: [phone]
Email: [e-mail]
20 + TSL.R.030 RIBBON HAND DRYER MANUAL