Thermo Pride AH2436AE1 Supplement

MAC-202
ECN 5577-MA 190924
13 & 14 SEER
AIR HANDLER
INSTALLATION & SERVICE MANUAL
MODELS: AH2436AE1, AH4260AE1,
AH2436BE1, AH4260BE1
PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION AND BEFORE
PERFORMING ANY SERVICE OR MAINTENANCE THESE INSTRUCTIONS MUST
BE LEFT WITH THE USER AND SHOULD BE RETAINED FOR FUTURE
REFERENCE BY QUALIFIED SERVICE PERSONNEL
: Improper installation, adjustment, alteration, service, or maintenance can
cause injury or property damage. Refer to this manual. For assistance or additional
information consult a qualified installer, service agency, or manufacturer listed below.
THERMO PRODUCTS, LLC.
BOX 237
DENTON, NC 27239
PHONE: [phone] MADE N USA

TABLE OF CONTENTS
SECTION BEGINNING PAGE
SAFETY SECT ON 1
KNOCKDOWN OF A R HANDLER 2
REASSEMBLY OF A R HANDLER 3
SETT NG UP THE A-CO L FOR A R COND T ON NG 4
COUNTERFLOW OR ENTAT ON 6
NSTALLAT ON OF HOT WATER CO L 8
BLOWER A R ADJUSTMENT 9
DUCT SYSTEM 13
DUCT S Z NG CHART 14
NDOOR EVAPORATOR CO L 14
TUB NG L NE SETS 14
HOW TO MEASURE L QU D SUB-COOL NG 18
MEASUR NG TEMPERATURE DROP ACROSS THE “A” CO L 19
ELECTR CAL 19
UA ADAPTER CAB NET 22
RECOMMENDED SUSPENS ON PROCEDURE FOR AH A R HANDLER 22
ECM TROUBLE SHOOT NG 23
TROUBLE SHOOT NG CHARTS 26
SEQUENCE OF OPERAT ON 28
REPLACEMENT PARTS L ST 29

1
SAFETY SECTION
This page contains various warnings and cautions found throughout this Service and nstallation Manual.
Please read and comply with the statements on the cover and the statements below.
: Improper installation, adjustment, alteration, service, or maintenance can cause injury
or property damage. Refer to this manual. For assistance or additional information consult a
qualified installer, service agency, or manufacturer listed below.
: f drilling or screwing into panel or plate is necessary, make certain drill or screw does not
penetrate into any part of evaporator coil or hot water coil and cause damage. Personal injury and/or
property damage may result.
: Do not use this system if any part has been under water. mmediately call a qualified
service agency to inspect the system and to replace any part of the electrical or control system which has
been under water.
: The cooling and heating coils must be cleaned by a qualified service person.
: This air handler is not to be used to condition during construction.
: When testing electrical equipment, always follow standard electrical procedures and
precautions.
: DO NOT wet electronic components during hydronic testing. Wetting electronic
components may damage circuitry and cause a hazardous situation. Dry moisture from all leads and
terminals if wetting occurs. Wait at least 24 hours for the circuit to fully dry before energizing the system.
: Personal injury or property damage could result from major repair or service of this system
by anyone other than a qualified contractor.
: f you do not follow these instructions exactly an unsafe condition may result causing
personal injury, loss of life or property damage.
nstallation and service personnel are required by some states to be licensed. Persons not qualified shall not
install this equipment nor interpret these instructions.
All local codes and regulations take precedence over the instructions in this manual and should be followed
accordingly. n the absence of local codes, installation must conform with these instructions, regulations of
the National Fire Protection Association and provisions of the National Electric Code.

2
AIR HANDLER
Each air handler is shipped with an evaporator coil preinstalled. The AH2436A(B)E1 is shipped with a
13U2436AB14 evaporator coil for 2 to 3 ton operation. The AH4260A(B)E1is shipped with a
13U4848AH20 evaporator coil for 3 to 5 ton operation.
The construction of the air handler permits easy knockdown and reassembly. See Figure A & B.
Figure A
FOLLOW THESE STEPS FOR KNOCKDOWN OF AH2436:
1. Start with unit setting in a vertical position (Figure A).
2. Remove blower access door.
3. Remove screws from front a-coil access panel, front heating option access panel, front middle panel
and supply air end casing.
4. Remove the front A-coil drain pan retainer and the horizontal drain pan support shipping screw(s) from
the right side casing.
5. Remove the evaporator a-coil assembly.
6. Remove the side support drain pan angles and A-coil bottom front and rear supports.
7. Disconnect power leads and unplug circulation pump connector from the blower control board.

3
8. Remove the screws that secure the blower assembly to the blower pan and pull blower sub-assembly
out the front of the unit.
9. Remove screws that secure the blower pan to the side & rear casings.
10. Push the front edges of the side casings slightly apart and remove the blower pan.
11. Remove screws from the return air end panel and side & rear casings.
12. Remove side & rear casings from the return air end panel.
REASSEMBLY OF AH2436
To reassemble the air handler, reverse steps above starting with number 12.
CONVERTING AH2436 FROM “LEFT TO RIGHT” AIRFLOW TO “RIGHT TO LEFT”
AIRFLOW:
 The AH2436 is shipped ready for horizontal “left to right” airflow or vertical operation.
 f horizontal “right to left” airflow is required, follow these steps:
SEE F GURE 1 FOR STEPS 1 THRU 6
1. Remove front panels from unit, and pull the coil assembly from the housing.
2. Remove the horizontal drain pan, and re-install it to the opposite side of the coil. Note: horizontal
drain pan must have drain plugs tightly closed in the rear of the unit.
3. Remove the top plate.
4. Remove the water diverter, and re-install it to the opposite slab.
5. Replace the top plate, and apply sealant to seal any air gaps.
6. Slide the coil assembly w/drain pan back into the housing.
Figure 1

4
Figure B
FOLLOW THESE STEPS FOR KNOCKDOWN OF AH4260
1. Start with unit setting in a vertical position (Figure B).
2. Remove the blower access door and front A-coil access panel.
3. Remove front tie panel (four screws).
4. Remove four screws between left/right side blower module casings and left/right side coil module
casings.
5. Remove two screws between rear blower module casing and rear coil module casing.
6. Top blower section is now disengaged from bottom coil section. Lift top off of bottom section.
7. f the Air Handler needs to be completely knocked down, follow steps in procedure for the
knockdown of the AH2436.
REASSEMBLY OF AH4260
To reassemble the air handler, reverse steps above starting with number 7.
SETTING UP THE A-COIL FOR AIR CONDITIONING
The AH2436 & AH4260 come with the A-coil pre-installed for vertical and left to right horizontal airflow.
The A-coil can also be re-positioned for counterflow operation.
IMPORTANT: When air handler is installed in attic above a finished ceiling, it is recommended that a
safety overflow pan with its own separate drain be installed under the entire unit.

5
For a right to left horizontal air flow the following steps 1-7 must be followed.
Otherwise skip to step 8.
Reversing the horizontal orientation
1. Remove the front a-coil access panel of the air handler.
2. Remove the front a-coil drain pan retainer.
3. Remove the horizontal drain pan support shipping screw(s) from the right side casing.
4. Remove the A-coil assembly and slip the horizontal drain pan assembly off of the right side of the
A-coil.
5. Slip the horizontal drain pan assembly onto the left side of the A-coil.
6. Re-install the A-coil assembly into the air handler. The A-coil drain pan should slide under the rear
retention clip. The horizontal drain pan assembly should rest against the left side casing insulation
and the side support angle.
7. Re-install the front a-coil drain pan retainer in front of the a-coil drain pan.
For all orientations
8. Cut open the appropriate drain pan drain access hole in the front A-coil access panel.
9. Slip the Suction line grommet panel over the suction line up to the access panel surface.
Figure C
11. Make appropriate liquid and suction line connections to coil and braze connections.
NOTE: A wet rag makes an excellent heat sink for tubing and grommets.
: f drilling or screwing into panel of plate is necessary, make certain drill does not penetrate
into any part of evaporator coil or hot water coil to avoid personal injury and/or property damage.
13. Position grommet panel on bottom door surface and secure in place with screws. Refer to Figure C.

6
14. Make appropriate condensate drain connections and seal the access opening.
For counterflow orientations:
Figure D
To convert AH2436 to counterflow:
1. Remove front A-coil access panel
2. Remove front a-coil drain pan retainer and the horizontal drain pan support shipping screws from
the right side casing.
3. Remove the A-coil assembly. Slide the horizontal drain pan assembly off of the right side of the A-
coil and discard.
4. Remove A-coil bottom front, side, rear supports, side support drain pan angles and rear a-coil drain
pan retainer.
5. Turn air handler over.
6. Re-install supports, angles and retainer removed in step 4 in the counterflow configuration using
pre punched holes located in the center of the casings.
7. Re-install A-coil and front a-coil drain pan retainer.
8. Re-install front A-coil access panel.

7
Figure E
To convert AH4260 to counterflow:
1. Remove the blower access door and front a-coil access panel.
2. Remove front tie panel (four screws).
3. Remove four screws between left/right side blower module casings and left/right side coil module
casings.
4. Remove two screws between rear blower module casing and rear coil module casing.
5. Top blower section is now disengaged from bottom coil section.
6. Lift blower module off of coil module.
7. Turn blower module over.
8. Remove return air end casing from coil module.
9. Place coil module on top of inverted blower module.
10. Re-install return air end casing on top of coil module and secure with screws.
11. Re-install all screws which secure blower module to coil module.
12. Re-install front tie panel.
13. Re-install blower access door and front a-coil access panel.

8
INSTALLATION OF THE HOT WATER COIL:
1. Remove top door of air handler.
2. Slide hot water coil's side hanger brackets into coil channel (retaining channel) in the air handler. See
Figure F.
3. Push coil into unit until the coil is stopped by the back casing.
4. Cut out appropriate holes in insulation, realign top door and secure into place.
5. Make appropriate hydronic connections to inlet (blower side) and outlet (duct side) of coil and braze
into place.
6. Seal connections through panel with duct sealer or equivalent.
Figure F
: f drilling or screwing into panel or plate is necessary, make certain drill does not penetrate
into any part of evaporator coil or hot water coil. Personal injury and/or property damage may result.

9
Figure G
NOTE: Drain lines must be pitched no less than 1/4" per foot away from the air handler.
BLOWER AIR ADJUSTMENT
The ECM blower control must be set in order to
establish proper air movement Use the following steps to
do this:
1. dentify to tonnage of the condensing unit that will be
used.
2. f Hydronic heat is to be used, identify your BTU heat
requirements, preferred supply air temperature, water
temperature and water flow through the coil in gallons per
minute.
3. Locate the blower control board mounted to the front of
the blower assembly.
4. Locate the red switch block labeled SW1 for adjusting the
Heating and Cooling blower speed.
5. Locate SW2, just below SW1, for adjusting Blower
delays.
Figure H

10
BLOWER COOLING SPEEDS
Refer Table C1 for setting switches 4, 5 & 6 for the A/C sizing.
BLOWER HEATING SPEEDS WITH HYDRONIC COIL
n the next two pages:
1. Locate the page that refers to the Air Handler to be set up.
2. Find the line(s) on the chart that best represents the water temperature and gallons per minute available.
3. Find the point along the curve that best fits the BTU and Supply Air temperature desired.
4. Read the letter associated with that point and use it to find the switch settings in the table below the
chart.
(The table below the switch settings represent the actual numbers represented by the chart )
Table C1 COOLING SWITCH SETTINGS
A/C
TONS
CFM
AH2436A/BE1 COOL
Settings (SW1)
AH4260A/BE1 COOL
Settings (SW1)
4 5 6 4 5 6
2 800 OFF OFF OFF
2-1/2 1000 ON OFF OFF
3 1200 OFF ON OFF OFF ON OFF
3-1/2 1400 ON ON OFF
4 1600 OFF
OFF ON
5
1800 ON OFF ON
2000 OFF
ON ON
2200 ON ON ON
S aded cells represent t e factory settings

11
HYDRONIC COIL MODEL HC1-B
AH2436*E1 Temperature & Heat Values at 140, 160 & 180
0
F and
3,4,5,6 & 7 gallons per minute at selected speeds
95
105
115
125
135
145
155
25 35 45 55 65 75 85
Heating Capacity (KBTU/H)
Supply Air w/70º Return (ºF)
7gpm:180
6pgm
5gpm
4gpm
3gpm
7gpm:160
6gpm
5gpm
4gpm
3gpm
7gpm:140
6gpm
5gpm
4gpm
3gpm
140
0
F
Water
180
0
F
160
0
F Water
A
B
C
D
E
F
G
H
Motor Speed (A,B,C etc.)
SPEED CFM
1
2
3
A
689
OFF
OFF
OFF
B
754
ON
OFF
OFF
C
819
OFF
ON
OFF
D
897
ON
ON
OFF
E
975
OFF
OFF
ON
F
1066
ON
OFF
ON
G
1170
OFF
ON
ON
H
1300
ON
ON
ON
Water
Temperature
Flow Tubeside
PD
CFM 689 (A) 754 (B) 819 (C) 897 (D) 975 (E) 1066 (F) 1170 (G) 1300 (H)
Supply Air (ºF
151º
148º
145º
142º
139º
136º
133º
129º
Heat (Kbtu/H
61517
64858
67946
71362
74504
77871
81378
85332
Supply Air (ºF
149º
146º
143º
140º
137º
134º
131º
127º
Heat (Kbtu/H
60283
63437
66346
69553
72493
75631
78888
82545
Supply Air (ºF
147º
144º
141º
138º
135º
132º
128º
125º
Heat (Kbtu/H
58593
61512
64191
67131
69813
72663
75606
78893
Supply Air (ºF
144º
140º
137º
134º
131º
128º
125º
121º
Heat (Kbtu/H
56163
58766
61139
63727
66073
68549
71090
73907
Supply Air (ºF
139º
135º
132º
129º
126º
123º
120º
116º
Heat (Kbtu/H
52393
54554
56507
58615
60509
62490
64505
66717
Supply Air (ºF
136º
133º
131º
128º
126º
124º
121º
118º
Heat (Kbtu/H
50092
52795
55294
58057
60597
63317
66151
69343
Supply Air (ºF
134º
132º
129º
127º
124º
122º
119º
116º
Heat (Kbtu/H
49061
51611
53962
56554
58928
61461
64090
67039
Supply Air (ºF
132º
130º
127º
125º
122º
120º
117º
114º
Heat (Kbtu/H
47654
50011
52174
54547
56711
59009
61382
64031
Supply Air (ºF
130º
127º
125º
122º
120º
117º
114º
111º
Heat (Kbtu/H
45639
47738
49652
51738
53629
55624
57670
59939
Supply Air (ºF
126º
123º
120º
118º
115º
113º
110º
107º
Heat (Kbtu/H
42530
44272
45845
47544
49069
50664
52286
54068
Supply Air (ºF
121º
119º
117º
115º
113º
111º
109º
107º
Heat (Kbtu/H
38730
40806
42723
44842
46788
48872
51041
53484
Supply Air (ºF
120º
118º
116º
114º
112º
110º
108º
106º
Heat (Kbtu/H
37900
39865
41666
43651
45468
47406
49417
51672
Supply Air (ºF
118º
116º
114º
112º
110º
108º
106º
104º
Heat (Kbtu/H
36792
38597
40252
42067
43721
45478
47290
49313
Supply Air (ºF
116º
114º
112º
110º
108º
106º
104º
102º
Heat (Kbtu/H
35200
36806
38268
39862
41305
42828
44390
46121
Supply Air (ºF
113º
111º
109º
107º
105º
103º
101º
99º
Heat (Kbtu/H
32760
34090
35291
36588
37751
38968
40206
41565
1.16
1.94
1.13
5.67
4.25
4.15
2.95
3.02
1.99
2.88
1.89
1.11
5.54
Heat Settings (SW1)
180º F
7 gpm
6 gpm
5 gpm
4 gpm
3 gpm
5.42
4.05
160º F
7 gpm
6 gpm
5 gpm
4 gpm
3 gpm
140º F
7 gpm
6 gpm
5 gpm
4 gpm
3 gpm

12
HYDRONIC COIL MODEL HC2-A
AH4260*E1 Temperature & Heat Values at 140, 160 & 180°F
and 7,8,9 & 10 gallons per minute at selected speeds
100
110
120
130
140
150
40 60 80 100 120
Heating Capacity (KBTU/H)
Supply Air w/ 70° Return (°F)
10gpm:180
9gpm
8gpm
7gpm
10gpm:160
9gpm
8gpm
7gpm
10gpm:140
9gpm
8gpm
7gpm
180
0
F Water
160
0
F Water
140
0
F
Water
AB
C
D
E
F
G
H
Motor Speed (A,B,C etc.)
Heat Settings (SW1)
SPEED
CFM
1
2
3
A
1007
OFF
OFF
OFF
B
1102
ON
OFF
OFF
C
1197
OFF
ON
OFF
D
1311 ON ON OFF
E
1425
OFF
OFF
ON
F
1558
ON
OFF
ON
G
1710
OFF
ON
ON
H
1900
ON
ON
ON
Supply Air (
o
F 148 146 144 141 139 136 133 130
Heat (Kbtu/H 86 91 96 101 106 112 117 124
Supply Air (
o
F 147 145 142 140 137 135 132 129
Heat (Kbtu/H 85 90 94 99 104 109 115 121
Supply Air (
o
F 146 144 141 138 136 133 130 127
Heat (Kbtu/H 83 88 92 97 102 107 112 118
Supply Air (
o
F 145 142 139 137 134 131 129 125
Heat (Kbtu/H 82 86 90 95 99 104 109 114
Supply Air (
o
F 134 132 130 128 126 124 121 119
Heat (Kbtu/H 70 74 78 82 86 91 95 101
Supply Air (
o
F 133 131 129 127 125 123 120 118
Heat (Kbtu/H 69 73 77 81 85 89 94 99
Supply Air (
o
F 132 130 128 126 124 121 119 117
Heat (Kbtu/H 68 72 75 79 83 87 91 96
Supply Air (
o
F 131 129 127 124 122 120 118 115
Heat (Kbtu/H 66 70 73 77 81 84 88 93
Supply Air (
o
F 119 118 116 115 113 111 110 108
Heat (Kbtu/H 54 57 60 64 67 70 74 78
Supply Air (
o
F 119 117 116 114 112 111 109 107
Heat (Kbtu/H 53 56 59 62 66 69 72 76
Supply Air (
o
F 118 116 115 113 111 110 108 106
Heat (Kbtu/H 52 55 58 61 64 67 70 74
Supply Air (
o
F 117 115 114 112 110 109 107 105
Heat (Kbtu/H 51 54 57 60 62 65 68 72
Inlet Water
Temperature Flow Tubeside PD CFM 1007 (A) 1102 (B) 1197 ('C) 1311 (D) 1425 (E) 1558 (F) 1710 (G) 1900 (H)
180
o
F H
2
O
10 gpm 1.88
9 gpm 1.54
8 gpm 1.23
7 gpm 0.95
160
O
F H
2
O
10 gpm 1.92
9 gpm 1.57
8 gpm 1.25
7 gpm 0.97
140
o
F H
2
O
10 gpm 1.95
9 gpm 1.6
8 gpm 1.27
7 gpm 0.99

13
BLOWER TIME DELAY
n cases where the yellow wires are used to start and stop the hydronic pump, SW2 may be used to delay
when the blower is cycled on or off to increase comfort and efficiency.
Use Table D1 to set the switches appropriately
Table D1: Delays before blower cycles “ON or “OFF”
SW2 Positions “ON” Delay SW2 Positions “OFF” Delay
1 2 (Seconds) 3 4 (Minutes)
OFF OFF 30 OFF OFF 2
ON OFF 60 ON OFF 4
OFF ON 120 OFF ON 6
ON ON 480 ON ON 8
DUCT SYSTEM
The duct system and load sizing calculation should follow the design standards of Air Conditioning
Contractors of America (ACCA) - manuals D & J - or the American Society of Heating, Refrigeration and
Air Conditioning Engineers, nc. (ASHRAE) Latest Edition Fundamentals Volume.
To aid you in evaluating existing duct systems quickly, review the chart on Page 14 which shows the CFM
capacity for square inch areas, based on .10" wc static pressure (SP) loss on the supply systems.
Each of the system's components (trunk lines, take-offs, runs and register and grill-free areas) must be
properly sized and matched together to ensure you are obtaining the air handling capacity of the duct
system. A 12x8 duct with a 400 CFM capacity, for example, MAY NOT flow 400 CFM if the register(s)
to which it connects can only flow a total of 200 CFM.
The air handling capacity MUST BE EQUAL TO the supply system at a minimum when sizing the return
air duct system. t is recommended to follow design parameters set down by ACCA or ASHRAE on the
return air duct systems.

14
DUCT SIZES FOR HOMES
Velocity Approximately 800 Feet Per Minute
THE INDOOR EVAPORATOR COIL
1. EVAPORATOR COIL is a finned coil through which air in the home is circulated. Heat from the air is
transferred to the liquid refrigerant inside the evaporator coil. The coils for use in AH air handlers are in an
A-shaped configuration (A Models).
2. CONDENSATE DRAIN PAN is attached to the bottom of the evaporator coil to collect water
condensed out of the air. Two drain fittings are provided for connection to a convenient drain point.
3. HORIZONTAL CONDENSATE DRAIN PAN is attached to the right side of the first one for
horizontal left to right air flow. t may relocated to the left side as well. A drain fitting is provided for
connection to a convenient drain point.
TUBING LINE SETS
1. SUCTION LINE is an insulated large copper tube connecting the outlet of the A/C evaporator to the
suction inlet of the A/C CONDENSER

15
2. LIQUID LINE is a single small tube connecting the outlet of the A/C condenser to the expansion valve
inlet on the A/C evaporator coil.
TUBING SIZE REFERENCE CHART
Tube Diameter for Total Line Length
0-50’ 50-75’ 75-100’
MODEL Suction Liquid Suction Liquid Suction Liquid
HP14241A1, HP14301A1,
AC14241E2, AC14301E2 3/4” 3/8” 7/8” 3/8” 1-1/8” 1/2”
HP14361A1, HP14421A1,
HP1448xA1, HP1460xA1 7/8” 3/8” 1-1/8” 1/2” 1-1/8” 5/8”
AC14361E2, AC14421E2,
AC1448xE2, AC1460xE2 7/8” 1/2” 1-1/8” 1/2” 1-1/8” 5/8”
NOTES:
For line lengths over 25’ adjust charge accordingly per foot of variation from chart.
.65 oz. per foot for 3/8” and 3/4” line set
.674 oz. per foot for 3/8” and 7/8” line set
.694 oz. per foot for 1/2” and 7/8” line set
.72 oz. per foot for 1/2” and 1” line set
.76 oz. per foot for 5/8” and 1-1/8” line set
These charges are to be used in conjunction with a liquid sub-cooling measurement for best performance.

16
TUBING INSTALLATION
The compressor oil is constantly pumped through the refrigerant lines in normal operation of an air
conditioning system. To ensure proper lubrication of the compressor by avoiding oil accumulation at
undesirable points in the system, follow the guidelines listed below:
1. No traps in the suction line are necessary if the outdoor condensing unit is level with the indoor
evaporator coil or the indoor evaporator coil is 4 feet or less lower then the outdoor condensing unit.
Any horizontal runs of suction line should have minimum 1/2" pitch for every 10 feet of line towards
the outdoor condensing unit. See Figure .
Figure I
2. A trap is necessary in the suction line at the indoor evaporator coil if the indoor evaporator coil is
more than 4 feet below the outdoor condensing unit.
Figure J

17
NOTE: Multiple suction line traps are recommended for longer or multiple suction lines. See Figure J.
An inverted trap should be installed on the horizontal suction line near the evaporator coil to prevent liquid
flood back to the compressor (See Figure K.) if the indoor evaporator coil is located 10’ or more above the
condensing unit.
Figure K
A gradual loop in the tubing can be constructed to take up the excess tubing if you find that too much
tubing has been brought onto a job. Such a loop MUST be kept in a horizontal (flat) plane to avoid
trapping the oil.
Refrigerant lines should be inserted into a suitable conduit or raceway when the lines are to be buried
between the building and the outdoor condensing unit. The lines must be provided with sufficient
protection and support to prevent damage when installed above ground.
When making "on the job" tubing, a solder of 95% tin, 5% antimony or any of the silver solders such as
SilFos, Phos-Copper, Easy-Flo 35 or 45, should be used. No attempt will be made here to instruct proper
soldering or brazing technique but it is necessary that the installer be properly instructed in accordance with
good existing practices.
All joints and fittings must be properly leak tested as per EPA guidelines after “on the job” tubing has been
made up. The line set and the evaporator coil must be evacuated to 29.96” Hg (1000 microns) or lower
when all joints and fittings are leak free. The service valves on the condenser may then be opened to release
the refrigerant to the system. Verify proper system performance. See condensing unit manual for additional
performance data.