THIS END UP FURNITURE Classic Small Dining Room Table User manual

THIS END UP FURNITURE CO.
P.O. Box 5410, Sanford, North Carolina 27331
[phone] [phone] Fax [phone] www.thisendup.com
June 2015
Classic Dining Room Table Assembly Instructions
Small an Me ium Dining Room Table
Pages 2
Large Dining Room Table
Pages 3

Dining Room Table Assembly Instructions
D
A
E
B
C
F
G
H
BRACKET
LEVELER
Tools Nee e
1 9/16” Wrench or Socket and Ratchet
1 Flat Head Screwdriver
Parts Inclu e
A Table Top (1)
B Table Leg (2)
C Center Board (1)
Har ware Kit
D 5” Lag Bolt (4)
E Flat Washer (4)
F 4 1/2” Machine Bolt (4)
G 1/4” Flat Washer (4)
H Wing Nut (4)
ASSEMBLY INSTRUCTIONS
1. Place table top (A) face down on floor.
2. To assemble base, attach legs (B) to centerboard (C) using (4) 5" lag bolts
(D) and (4) washers (E). Do not tighten lag bolts completely.
3. Lower base upside down onto top (A).
4. Line up holes in base with holes in brackets on the underside of table top (A).
5. Attach using (4) machine bolts (F) with (8) washers (G) and (4) wing nuts
(H). Make sure nuts are tight. **NOTE: MAKE SURE UPPER CROSS-
MEMBERS OF LEGS (B) ARE TIGHT AGAINST THE UNDERSIDE OF
TOP (A).
6. Fully tighten lag bolts (D).
7. Turn table into upright position. **NOTE: IF TABLE ROCKS, THERE ARE
LEVELERS ON THE BOTTOM OF THE BASE. THESE CAN BE UN-
SCREWED B HAND TO LEVEL THE TABLE
THIS END UP FURNITURE CO.
P.O. Box 5410 Sanford, North Carolina 27331
[phone] [phone] Fax [phone] www.thisendup.com
June 2015
D
E
F
G
H

ED
A
B
C
F
G
H
BRACKET
LEVELER
I
J
THIS END UP FURNITURE CO.
P.O. Box 5410 Sanford, North Carolina 27331
[phone] [phone] Fax [phone] www.thisendup.com
June 2015
TOOLS NEEDED
1 9/16" SOCKET & RATCHET
1 FLAT HEAD SCREWDRIVER
1 PHILLIPS HEAD SCREWDRIVER
PARTS LIST
A TABLE TOP
B TABLE LEG
C CENTERBOARD
D 5" LAG BOLT (4)
E WASHER (4)
F 4 1/2" MACHINE BOLT (4)
G 1/4" WASHER (8)
H WING NUT (4)
I TABLE BRACE(1)
J 1 1/2" SCREW (10)
ASSEMBLY INSTRUCTIONS
1. Place table top (A) face down on floor.
2. To assemble base, attach legs (B) to centerboard (C) using (4) 5" lag
bolts (D) and (4) washers (E). Do not tighten lag bolts completely.
3. Lower base upside down onto top (A).
4. Line up holes in base with holes in brackets on the underside of table
top (A).
5. Attach using (4) machine bolts (F) with (8) washers (G) and (4) wing
nuts (H). Make sure nuts are tight.**NOTE: MAKE SURE UPPER
CROSSMEMBERS OF LEGS (B) ARE TIGHT AGAINST THE
UNDDERSIDE OF TOP (A).
6. Fully tighten lag bolts (D).
7. Attach Table Brace (I) between legs with (10) screws (I) to underside
of top.
8. Turn table into upright position.**NOTE: IF TABLE ROCKS, THERE
ARE LEVELERS ON THE BOTTOM OF THE BASE. THESE CAN
BE UNSCREWED BY HAND TO LEVEL THE TABLE.
Dining Room Table Assembly Instructions
Large Dining Room Table