Thrustmaster T818 User manual

ENGLISH
FRANÇAIS
DEUTSCH
NEDERLANDS
ITALIANO
ESPAÑOL
PORTUGUÊS

User Manual
Carefully read
the instructions provided in this
manual before installing the product, before
any use
of the product and before any maintenance.
Be sure
to follow the safety instructions.
Failure to follow these
instructions may result in accidents and/or damage
.
Keep this manual so that you can refer to
the
instructions in the future.

TABLE OF CONTENTS
1. INSTALLATION PROCEDURE.........................6
2. FAQ AND TECHNICAL SUPPORT ................12

3
The Cockpit Mounting Kit is a system for mounting the
T818 base in cockpits, composed of a support plate and
a set of screws with nuts.

4
Mounting diagram in cockpits
A mounting diagram for cockpits is available at
https://support.thrustmaster.com/ product/t818-
cockpit-mounting-kit
You can print out the diagram and use it in your
cockpit in order to verify your cockpit’s compatibility.
Most cockpits available on the market are already
compatible with Thrustmaster bases (TS-
PC Racer
Servo Base, TS-XW Servo Base, T-
GT II Racing
Wheel Servo Base, T300 Racing Wheel Servo Base).
Using the Cockpit Mounting Kit
therefore lets you
install the ba
se in a cockpit without having to adapt
anything.

5
Only use the mounting systems and accessories
specified by the manufacturer.

6
1. Installation procedure
- Assemble the Cockpit Mounting Kit on the T818 base.
- Tighten the four mounting screws clockwise.

7
- Position the T818 base with the Cockpit Mounting
Kit on the cockpit’s shelf, lining up the perforations.

8
- Screw in the four mounting screws clockwise.

9
Set of screws
Use these screws included with the
Cockpit Mounting
Kit
to attach the base to the cockpit’s shelf. Three
configurations
of screws are possible, depending on
your cockpit.

10
Stability
Do not mount the base with the
Cockpit Mounting Kit
on the front edge or rear edge of the shelf.
Everything
must fully rest on the shelf, and be screwed into the
shelf.

11
Getting into and out of the cockpit
Do not use the wheel’s rim as a lever to help you get
into or out of your racing seat: by doing so, you risk
damaging your base and/or your wheel.

12
2. FAQ and technical support
Do you have questions regarding the Cockpit Mounting
Kit, or are you experiencing technical problems? If so,
visit the Thrustmaster technical support website:
https://support.thrustmaster.com/ product/t818-
cockpit-mounting-kit

Manuel de l’utilisateur
Lisez attentivement
les instructions fournies dans ce
manuel avant d'installer le produit, avant
toute
utilisation et avant tout entretien. Conformez-
vous aux
consignes de sécurité. Le non-
respect de ces
instructions peut causer des accidents et/ou des
dommages. Conservez
ce manuel pour toute
consultation ultérieure des instructions.

TABLE DES MATIÈRES
1. PROCEDURE D’INSTALLATION.....................6
2. FAQ ET SUPPORT TECHNIQUE ...................12

3
Le Cockpit Mounting Kit est un système de montage de
la base T818 sur cockpits, composé d’une plaque de
support et d’un jeu de vis avec écrous.

4
Plan de montage sur cockpit
Un plan de montage sur cockpit est disponible sur
https://support.thrustmaster.com/ product/t818-
cockpit-mounting-kit
Vous pouvez l’imprimer et le reporter sur votre cockpit
pour vérifier sa compatibilité.
La plupart des cockpits disponibles sur le marché sont
déjà compatibles avec les bases Thrustmaster (TS-
PC
Racer Servo Base, TS-XW Servo Base, T-
GT II Racing
Wheel Servo Base, T300 Racing Wheel Servo Base).
L'utilisation du Cockpit Mounting Kit permet donc
d'installer la base sur un cockpit sans adaptation.

5
Utilisez uniquement les systèmes de fixation/
accessoires spécifiés par le fabricant.

6
1. Procédure d’installation
- Assemblez le Cockpit Mounting Kit sur la base T818.
- Serrez les quatre vis de fixation dans le sens horaire.

7
- Positionnez la base T818 avec le Cockpit Mounting
Kit sur la tablette du cockpit en faisant correspondre
les perforations.