Tiger Tool 15012 User manual

1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
•
Stay Alert! Watch what you are doing and use common sense when
operating this tool.
•
Inspect product for damage prior to using, do not use if product is
in unsafe condition.
•Do not operate tool while under the influence of drugs, alcohol,
or medication.
•
Always use safety equipment to prevent injuries. Approved face and
eye protection must always be worn by the operator, as well as others
in the work area.
•
Do not overreach, keep proper footing and balance at all times.
• Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving parts.
•
Keep hands clear of all pressurized hydraulic components.
• Always ensure hoses are free from sharp bends and kinks.
•
Keep your work area clean and well lit.
CAUTION: KEEP HYDRAULIC COUPLER PROTECTED WHEN NOT IN USE. DUST CAPS SHOULD BE USED ON COUPLERS WHEN NOT IN USE TO
AVOID CONTAMINANTS FROM ENTERING THE HYDRAULIC CYLINDER AND POWER SOURCE. THIS PRACTICE WILL HELP TO EXTEND THE LIFE OF
THIS PRODUCT AND ENSURE CONTINUED CONSISTENT OPERATION.
Safety Warning
Read all instructions and safety warnings prior to operation. Failure to do so could result in
equipment damage, personal injury, or even death.
Have What It Takes
Peterbilt Air Trac Pin
& Bushing Adapter
15012

1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Operating Instructions
Have What It Takes
Peterbilt Air Trac Pin
& Bushing Adapter
15012
Bushing Removal
1 Remove torque rod from the suspension. Figure A
2Thread on the 15001-55 cylinder adapter to the 17202
hydraulic cylinder.
3Attach the 15001-79 face plate on to the 15001-57 extension
tube and place the two pcs on to the 15001-55 cylinder
adapter and 17202 hydraulic cylinder assembly.
4Place the 15001-112 push adapter over one end of the
bushing and install one 15001-125 threaded pin, hand
tighten with the provided ¼" socket driver.
5Insert the 15001-3 pull-bar through the 15001-126 pull
adapter. Place the pull adapter/pull-bar over the other
end of the bushing and install the remaining 15001-125
threaded pin.
6Slide the hydraulic cylinder, cylinder adapter, spacer tube,
face plate over the pull-bar assembly and thread on the
15001-7 trigon nut, hand tighten.
7Connect your 10,000psi hydraulic pump to the cylinder and
apply force until the cylinder has fully extended (approx.
2"). Release pressure and hand tighten trigon nut. Repeat
until bushing is removed.
8Remove adapters from the old bushing and
disassemble tooling.
Figure A
15001-125
15001-57
15001-79
15001-55
15001-112
15001-126

Have What It Takes
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Operating Instructions
Bushing Installation
1Thread on the 15001-55 cylinder adapter to the 17202
hydraulic cylinder.
2Attach the 15001-79 face plate to the 15001-55
cylinder adapter (the 15001-57 extension tube is
not used for installation).
3Place the 15001-112 push adapter on to the new bushing
and install one of the 15001-125 threaded pins, tighten by
hand with the provided ¼" socket driver.
4Insert the 15001-3 pull-bar through the 15001-126 pull
adapter. Place the pull adapter/pull-bar over the other
end of the bushing and install the remaining 15001-125
threaded pin.
5Insert the pull-bar and bushing assembly through the eye
of the torque rod (threaded end of the pull-bar first) until
the bushing is up against the torque rod in the desired
orientation.
6Place the hydraulic cylinder, cylinder adapter, face plate
over the pull-bar and thread on the 15001-7 trigon nut,
hand tighten.
7Connect your 10,000psi hydraulic pump to the cylinder and
apply force until the cylinder has fully extended. Release
pressure and hand tighten trigon nut. Repeat until the
bushing is in desired installed depth.
8Remove adapters from the bushing and
disassemble tooling.
Here at Tiger Tool, your satisfaction is our number one
priority. Should you have any questions about this or any of
our products, please call us at 1.800.661.4661.
Peterbilt Air Trac Pin
& Bushing Adapter
15012

Part Number Qty.
1
1
1
2
1
1
1
16
Description
Spacer Tube
Cylinder Adapter
Peterbilt Air Trac Face Ring
Threaded Pin
.25" Socket Driver
Push Adapter
Pull Adapter
Magnets
Parts Breakdown
1.800.661.4 661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
Peterbilt Air Trac Pin
& Bushing Adapter
15012
15001-57
15001-55
15001-79
15001-125
15030-1
15 0 01-112
15001-126
15001-9
15001-57
15001-9
15001-79
15001-55
15030-1
15001-125
15001-112
15001-126