Timeguard WFAD3 Manual

Installation & Operating Instructions
WiFi 3 Way Adaptor
withUSB Ports
Model: WFAD3
Installation & Operating Instructions

1
1. General Information
These instructions should be read carefully
in full before installation, and retained for
further reference and maintenance.
2. Safety
• Do not plug in any appliance that
exceeds the capacity of the Smart Plug.
• Always ensure the plug of any appliance is
fully inserted into the Smart Plug outlet.
• If cleaning of the Smart Plug is
required, remove from mains power and
wipe Smart Plug with a dry cloth.
• Do not immerse in water or any other liquid.
• For indoor use only.
3. Technical Specifications
• 230V AC 50 Hz
• Switch Rating: 13A Total Load
• Manual ON/OFF Control
• USB Port Output: 5V 2.4A (Total)
• Operating Temperature: -0°c to +65°c
• Operating Humidity: ≤80%RH
• WLAN-Standard: 802.11 b/g/n
• Encryption: WEP/WPA/WPA2
• CE Approved
• EC Directives:
Conforms to the latest directives
Dimensions (H x W x D): 56 x 155 x 34mm

2
4. System Requirements
• Smartphone/Tablet with
at least iOS 8.0 or Android 5.0
• WLAN-enabled router: 2.4GHz
(Separate Band)
• Tuya Smart App
5. Downloading App
and Registration
Note: The smartphone or tablet
must be connected to a 2.4GHz band
on the router. Paring on the 5GHz
band will result in paring either timing
out or being unsuccessful. Refer to
your ISP (Internet Service Provider)
on separating the bands if required.
• Ensure your phone or tablet is connected
to your local Wi-Fi network.
• Download the Tuya Smart App onto
your phone or tablet by searching
for ‘Tuya Smart’ on Google Play Store
or the App Store. You can also scan the
applicable QR code below;

3

4
• Install the App and open
it to the registration screen.
Click on the ‘Register’ button.

5
• Tap ‘Agree’ to accept the privacy policy.

6
• Choose your region by selecting
the Country Code. Enter your email
address or phone number and
click ‘Get Verification Code’.

7
• Enter the Verification Code sent to the
email address or phone number that you
provided. Once you have successfully
entered the code, it will automatically
move you to the Password screen.
• Assign a Password (this must be between
6 to 20 characters including letters and
digits) and click ‘Done’.

8
• You are now registered and by default
will see the App home page.

9
6. Home Management
Note: Before adding any devices to your
account, structuring your household
(or the property) may be a consideration
if you plan on using Smart devices
in different rooms or locations.
• Select the ‘Me’ option from the home
page which will navigate you to your
personal settings. From here you can
setup a nickname for your profile i.e.
‘Mr Smith’s Account. After this select
the ‘Home Management’ option.

10
• Select the ‘Home Name’ option
and enter your last name or even
‘My Home’ if preferred. (This is required
to allocate devices to separate rooms later
once paired).

11
• Next tick the rooms you wish to assign
to your account; this can be changed
at any time and custom room names
can also be added.
• To navigate back to the home screen,
press the ‘Back’ button, and then
click Home.

12
7. Pairing your Device(s)
• To add a new device to your account,
click the ‘Add Device’ button
(or click on the + button in the
top right hand corner)

13
• Notice the different categories of
products; it is essential that the correct
product is selected for the pairing
process to be successful. For the Wi-Fi
3 Way Power Strip, choose the ‘Power
Strip (Wi-Fi)’ option from the list.

14
• Plug the Wi-Fi 3 Way Adaptor into a
socket with the power switch in the ON
position. Press and hold the round On/Off
button for a few seconds until the LED
starts to flash.
• When the LED is flashing press
the ‘Confirm indicator rapidly
blinking’ button. Enter the password
for the network and press the ‘Confirm’
button to pair the product to your
account (In most cases the password
should autofill).

15

16
• The App will pair the smart product
to the network. The time it takes for
pairing to complete, which will differ
depending on the network connection.
Shortly into the pairing process, the
flashing Status LED will become stable
(ON). This indicates that the product has
joined the network.

17
• If the following screen is displayed, then
the product has been paired successfully.
To rename your product, select the pencil
icon. If this is not required, click on the
‘Done’ button and you will guided to
the device controls menu.

18

19
• To navigate back to the home screen,
press the ‘Back’ button. The newly paired
Wi-Fi Smart Switch will now be listed.
Note: If the pairing process was not
successful, disconnect the mains supply
from the product and re-establish power
to the unit. Follow the bullet points from
’Section 7‘ to try again.