Titan Attachments LS3PT25 User manual

25 TON LOG SPLITTER
LS3PT25
198375
Operator’s Manual
Read the Operator’s Manual entirely. When you see this
symbol, the subsequent instructions and warnings are
serious follow without exception. Your life and the lives
of others depend on it!

2
GENERAL WARNINGS
READ and UNDERSTAND this manual completely before using 3PT Hitch 25 Ton Log Splitter.
Operator must read and understand all safety and warning information, operating instructions,
maintenance, and storage instructions before operating this equipment. Failure to properly operate and
maintain the log splitter could result in serious injury to the operator or bystanders.
OPERATION WARNINGS
•Do not at any time have people, sit, or stand on the log splitter.
•Do not allow children to play on, stand upon or climb on the log splitter.
•Never carry any cargo or wood on your log splitter
•Always inspect the log splitter before using to assure it is in good working condition.
•Replace or repair damaged or worn parts immediately.
•Check for hydraulic fluid leaks by passing a piece of paper or cardboard underneath or over the
area of the leak. Do not check for leaks with your hand.
•Always check and tighten hardware and assembled parts before operation.
•Do not adjust the hydraulic valve. The pressure relief valve on the log splitter is preset at the
factory. Only a qualified service technician should perform this adjustment.
•Do not exceed equipment maximum load capacity of 25 tons.
•Do not alter the log splitter in any manner. Any alteration will void the warranty and could cause the
log splitter to be unsafe to operate.
•Always operate the log splitter on clear and level ground.
•Do not operate the log splitter at night, only during daylight hours.
CRUSH AND CUT HAZARDS
•Always keep hands and feet clear from moving parts while operating the equipment.
•Always clear and keep work area clean and free of debris when operating.
•Always wear safety gear, eye protection, gloves and work boots when operating the log splitter.
ASSEMBLY IS REQUIRED
This product requires assembly before use. See “Assembly” section for instructions. Because of the weight
and/or size of the log splitter, it is recommended that another adult be present to assist with the assembly.
INSPECT ALL COMPONENTS closely upon receipt to make sure no components are missing or damaged.
WARNING
The warnings, cautions, and instructions outlined in this instruction manual cannot cover
allpossible conditions or situations that may occur. It must be understood by the operator
that common sense and caution are factors which cannot be built into this product and
must besupplied by the operator.
PROP 65 WARNING
This product can expose you to chemicals including lead and lead compounds which are known
to the State of California to cause cancer and birth defects or other reproductive harm. For more
information, go to www.P65Warnings.ca.gov.

3
HAZARD SIGNAL WORD DEFINITIONS
ABOUT YOUR 3PT 25 TON LOG SPLITTER
This hydraulic log splitter has a heavy-duty steel construction and up to 25 tons of ram force. The splitter is
designed to work in both the horizontal and vertical position. When there's work to be done,you need
outdoor power equipment you can rely on, this 3-point hitch log splitter will get the job done fast. Never
exceed the rated capacity of 25 tons when operating the log splitter.
Technical specifications on the log splitter are provided in the “Specifications” section of this manual.
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
DANGER DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.

4
CONTROLS AND FEATURES IDENTIFICATION
Read this owner’s manual before operating the equipment. Familiarize yourself with the location and
function of the controls and features. Save this manual for future reference.
1. Beam
2. Handle
3. Control Valve
4. Cylinder
5. Rear Support Leg
6. Main Cross Beam
7. Front Support Leg
3 PT HITCH 25 TON LOG SPLITTER ASSEMBLY
Set the shipping crate on a solid flat surface and carefully remove the lid. Use two people and takeall parts
out of the shipping crate and inspect the components to ensure there are no missing piecesbefore starting
to assemble the log splitter follow steps 1 through 2.
TOOLS REQUIRED
•18mm, 19mm Wrenches
•Wood Hammer
Inspect all Log Splitter Components.
If you have damaged components: Contact the freight company
thatdelivered the log splitter and file a claim.

5
ASSEMBLY INSTRUCTIONS
STEP 1: ATTACH SUPPORT LEGS
1. Attach front support leg (#2) to the main cross beam (#10) using hex bolt M12x100 (#4),
flat washer Ø12 (#5) and nylon lock nut M12 (#6), loosely tighten the nut.
2. On the other side of the main cross beam (10) attach the rear support leg (#19) using hex
bolt M12x90 (#18), flat washer Ø12 (#5) and nylon lock nut M12 (#6), loosely tighten the
nut.
3. Connect the front support leg (#2) and rear support leg (#19) to the bottom of the main
cross beam (10) using hex bolt M12x90 (#18), flat washer Ø12 (#5) and nylon lock nut
M12 (#6), tighten all the nuts.
4. Tighten all hardware.
STEP 2: ATTACH BEAM ASSEMBLY
1. Attach the beam assembly (#20) to the front support leg (#2) with the hitch pin (#3) andR-Pin
(#1), lower beam and secure with safety pin (#11).

6
SPLITTING FORCE AND CYCLE TIME
SPLITTING FORCE IN TONS
CYCLE TIME IN SECONDS
OPERATION INSTRUCTIONS
1. Set up the log splitter in a clear, level area.
2. Place a log on the beam against the foot plate. Make sure the log is securely up against foot plate.
3. Depress the valve handle so that the cylinder will drive the wedge into the log. Extend the cylinder
until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has
reached the end of its extension, retract the cylinder.
WARNING
Splitting force is determined by cylinder size and the tractor PSI. The cycle time depends
on the cylinder size and GPM’s that the tractor produces. Tractor should ideally produce
8-15 GPM at 1500 to 2500 PSI.
Do not exceed 3200 PSI. See tables below for approximate splitting force and cycle
time calculations. The 3-Point Log Splitter is designed for tractors with pressure ratings
that are under3200psi. Exceeding the recommended pressure rating will void the
warranty and damage the equipment.
WARNING
Read and understand the operating procedures before using this product! Failure to
comprehend and comply with warnings, cautions and instructions could result in serious
injuryor death. Operation of power equipment can be dangerous. It is the sole responsibility of the
operator to understand the assembly and safe operation of this product.

7
IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage thepump.
Always use extra care when splitting logs with unsquared ends.
IMPORTANT: To extend the life of the hydraulic cylinder, avoid “bottoming out” the wedge plate to thefoot
piece. To conform with industry safety standards the wedge stops 2 inches from the end of the stroke.
The log splitter can easily be rotated from horizontal to vertical operating position by removing and
replacing the lynch pin. Make sure the lynch pin is fully engaged and secure.
WARNING: Tilt slowly. Do not move from vertical to horizontal operating position until the support
frame legs are in a secure position. Tractor lift arms could fall resulting in serious injury.
MAINTENANCE AND STORAGE
WARNING
Improper maintenance and storage of the log splitter may void your warranty.
MAINTENANCE
1. With normal use the log splitter will not require any regular maintenance other than checking for
loose bolts and the inspection of hoses and fittings.
2. If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the 1/2 in. diameter
bolt that connects the wedge to the cylinder. The hose from the valve may need to be removed.
While the log splitter is in the horizontal position, loosen the hose clamp and disconnectthe hose
from the valve. Carefully lift the cylinder to allow the wedge to slide forward. The wedge can now be
lifted off and sharpened.
3. All replacement parts must meet manufacturer’s specifications.
What
When
How
Hoses Each Use
Inspect hoses for exposed wire mesh and leaks.
Replace
all worn or damaged hoses before using.
Hydraulic
Fittings
Each Use
Inspect fittings for cracks and leaks. Replace
alldamaged fittings before using.
Nuts and Bolts
Each Use
Check for loose bolts, tighten before operating.
Beam
Each Use
Apply grease to beam surface.
Moving Parts
Each Use
Clear debris from log splitter.
IMPORTANT:
If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement
parts that do not meet specifications may result in a safety hazard or poor operations.
STORAGE
•Before storing make sure the log splitter is clean and dry for years of trouble-free service.
•Lightly lubricate all log splitter surfaces and moving parts to prevent rust.
•Store indoors or protected area during severe weather and winter months.

8
SPECIFICATIONS
Ram Force:
19-25 Tons (*)
Tractor Categories:
CAT 1 & CAT 2
Hitch Tractor:
3 Point
Cycle Time:
11.5 – 15 Sec
Harden Steel Wedge:
8”
Max. Log Length:
26”
Hydraulic Cylinder:
4.13” x 24.5”
Max. Pressure: 3200 PSI
Valve:
Auto Return
Warranty:
3 Year / 1 Year Limited
(*) Ram Force depends on Tractor and Cylinder Diameter. (Reference charts on previous page) Splitting
Force is determined by cylinder size and tractor PSI. Cycle Time is determined by cylinder size and GPM
produced by tractor. Ideally tractor should produce 8 - 15 GPM at 1500 to 2500 PSI. Do not exceed 3200 PSI,
exceeding 3200 PSI will overstress log splitter mechanism and void warranty.

9
PARTS DRAWING AND PARTS LIST

10
PARTS DRAWING AND PARTS LIST
REF DRAWING NO. DESCRIPTION QTY
1 LSP25-00012-DX R Pin 1
2 LTS25-01000 Front Support Leg 1
3
LSP25-05000-DX
Hitch Pin
1
4 9101-12100-DX8.8 Hex Bolt 12x100 2
5 9301-12000-DX Flat Washer Ø12 16
6 9206-12000-DX Nylon Lock Nut M12 9
7 LSP25-00006-DX Safety Pin A 1
8 LSP25-00003-DX Spring 2
9
9404-03030-DX
Cotter Pin 3x30
2
10 LTS25-03000 Main Cross Beam 1
11 LSP25-00008-DX Safety Pin B 1
12 LTS25-00001-DX Suspension Pin V 1
13
T680-20000-DX
Lock Pin
3
14 LTS25-00002-DX Suspension Pin v 2
15 9301-22000-DX Flat Washer Ø22 2
16 9306-22000-DX Lock Washer Ø22 2
17 9201-22000-DX Hex Nut M22 2
18 9101-12090-DX8.8 Hex Bolt M12x90 6
19 LTS25-02000 Rear Support Leg 1
20 LSP25B-01000 Beam 1
21 LSP25-00004-DX Cylinder Pin 1
22 LSP25-00005-DX R Pin 2
23 LSP25A-08000 Cylinder 1
24 LSP25-00001-DX Metal Tube 1
25 LSP25-06000 Connector 2
26 N801-00005-CD Quick Connector 2
27 LST25-00003-DX Right Angle Connector 2
28 N29W-00001 Plate 1
29
9110-08010-DX
Screw M8x10
4
30 M1V24A-00001 Control Valve 1
31 LSP25-17000-DX Combination Connector 1
32 9901-15.2*2.4 O Ring 1
33 LSP25B-02000 Wedge 1
34 9101-12065-DX8.8 Hex Bolt M12x65 1

11
Attach the log cradle to the beam with the Ø12 flat washer
and M12 lock nut.
LOG CRADLE
Ø12 FLAT WASHER
M12 LOCK NUT

12
ACKNOWLEDGEMENT OF RISK AND RELEASE OF LIABILITY
The use of any equipment, including this one, involves the potential risk of injury. Apart from any
warranty claim that might be presented for a claimed defect in material or workmanship of the product,
you accept and assume full responsibility for any and all injuries, damages (both economic and non-
economic), and losses of any type, which may occur, and you fully and forever release and discharge
Titan, its insurers, employees, officers, directors, associates, and agents from any and all claims,
demands, damages, rights of action, or causes of action, present or future, whether the same be known
or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
This equipment must be used with care by capable and competent individuals under supervision, if
necessary.
WARNING
Do not overfill! Mower should be level
when checking oil in gear box.
some activities might be able to cause
electric shock
Sharp objects may be involved.
Use protective cover during maintenance.
TITAN LIMITED WARRANTY: TERMS, EXCLUSIONS AND LIMITATIONS OF REMEDIES
This product comes with a one (1) year limited warranty that can be found at
www.palletforks.com/warranty.html. Please review the same for all details regarding the Titan Limited
Warranty.
THE TITAN LIMITED WARRANTY FOUND AT WWW.PALLETFORKS.COM/WARRANTY.HTML IS
EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, EACH
OF WHICH IS HEREBY DISCLAIMED.

13
NEED HELP? CONTACT US FIRST.
1-800-605-7595
[e-mail]
www.palletforks.com
© 2021 Titan Brands