Könner & Söhnen KS 7THE 52/30 User manual

Electric horizontal log splitter
Please, read this manual
carefully before use! Owner’s Manual
KS 7THE 52/30
KS 8TKE 52/35
EN

INTRODUCTION
SAFETY INFORMATION 1
Thank you for your purchase of Könner & Söhnen products. This manual contains a brief description of
safety, use and debugging. More information can be found on the ocial manufacturer’s website in the
support section: ks-power.de/betriebsanleitungen.
You can also go to the support section and download the full version of the manual by scanning the QR
code, or on the website of the ocial importer of Könner & Söhnen products: www.ks-power.de/en.
Manufacturer reserves the right to make alterations into the generators, which may not be reected in this
manual. Pictures and photos of the product may vary from its actual appearance. At the end of this manual,
You may nd contact information which you are free to use in case of any issues occurrence.
All data, specied in this operation manual is the most up to date for the moment of its publishing. The
current list of service centers you can nd at the website of ocial importer: www.ks-power.de/en.
We care about the environment, therefore, we consider it expedient to saveWe care about the environment, therefore, we consider it expedient to save
paper and leave in print a short description of the most important sections.paper and leave in print a short description of the most important sections.
Be sure to read the full version of the manual before
getting started!
Failure to follow the recommendations marked with this
sign may lead to serious injury or death of the operator
or third parties.
Useful information while operating the machine.
ATTENTION – DANGER!
IMPORTANT!
Please, read this manual carefully before use!
WARNING!
PROTECTING YOURSELF AND THOSE AROUND YOU 1.1
Safety symbols and description of inscriptions can be found in the full web version.Safety symbols and description of inscriptions can be found in the full web version.
Always take the following precautions when using this machine:
• Always wear protective goggles or safety glasses with side shields while using the log splitter to protect
your eyes from possible thrown debris.
• Avoid wearing loose clothing or jewelry, which can catch on moving parts.
• We recommend wearing gloves while using the log splitter.
• Wear shoes with non-slip treads when using your log splitter. Do not use the machine while barefoot or
wearing open toed sandals.
•Wear long pants while operating the log splitter.
• Keep bystanders at least 50 feet away from your work area at all times. Stop the motor when another
person or pet approaches.
• Never allow children to operate the log splitter.
• Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people,
their property, and themselves.
www.ks-power.de/en |1

Operating this Log Splitter safely is necessary to prevent
or minimize the risk of death or serious injury. Unsafe
operation can create a number of hazards for you.
WARNING!
Always follow these precautions:
• Never open the switch box or motor cover. Never
attempt any electrical repairs yourself. If in doubt,
consult a qualied electrician, or contact your local
dealer for help or informations.
• Never use an extension cord that is not rated for
outdoor use.
• Never operate the Log Splitter if there is an elec-
trical hazard present.
• Never operate the Log Splitter in wet conditions
and always store under cover.
• Never operate the Log Splitter with a damaged
electrical cord or damaged extension cord.
• Never pull on the electrical cord to move the ma-
chine.
• Always grasp the electrical cord plug when un-
plugging the cord from the outlet; never pull the
plug out by the cord. Make sure your ngers do
not touch the metal prongs when plugging or un-
plugging.
• Never operate the Log Splitter unless the electri-
cal cord is plug
• If you are using an extension cord, keep the con-
nection between the electrical cord and the exten-
sion cord well away from any water.
• Never use an extension cord longer than 10 feet
and smaller than 1.5 mm2 or 20 feet and smaller
than 2.5 mm2 in diameter, the cord will produce
a voltage drop that will prevent the motor from
supplying full power and may cause damage to the
motor. Use of a smaller diameter extension cord
could result in melting of the insulation or even
create a re.
• Always keep the electrical cord and/or extension
cord away from excessive heat, oil, and sharp ob-
jects.
Always take the following precautions when operat-
ing this Log Splitter:
• The machine is designed to split logs. Do not use
it for any other purpose.
• Never operate your unit on a slippery, wet, mud-
dy, or icy surface.
• Exercise caution to avoid slipping or falling.
• Never, under any conditions, remove, bend, cut,
t, weld, or otherwise alter standard parts on the
Log Splitter. This includes all shields and guards.
Modications to your machine could cause person-
al injuries and property damage and will void your
warranty.
• Allow only one person to operate the Log Splitter
at any time. This includes placing the log on the
beam.
• If the machine should start making an unusual
noise or vibration, shut o the Motor, Unplug the
Power Cord, wait ve minutes for machine to cool
down then inspect for damage. Vibration is gener-
ally a warning of trouble. Check for damaged parts
and clean, repair and replace as necessary.
• Never tamper with safety devices. Check their
proper operation regularly.
• Before performing any maintenance or inspection
procedure on the Log Splitter, shut o the Motor,
unplug the Power Cord and wait ve minutes for
machine to cool down.
• Never allow people who are unfamiliar with these
instructions to use the Log Splitter.
• Never overload or attempt to split logs beyond
the recommendations listed in this manual.
• Never operate the machine when under the inu-
ence of alcohol, drugs, or medication.
• Use the machine only in daylight.
• Keep all nuts and bolts tight and keep the equip-
ment in good operating condition.
SAFETY WITH ELECTRIC - POWERED MACHINES 1.2
Never overlook the hazards of electricity.
WARNING!
www.ks-power.de/en |2

SPECIFICATIONS 2
Model KS 7THE 52/30 KS 8TKE 52/35
Log splitter type hydraulic kinetic
Voltage 230 V 230 V
Frequency 50 Hz 50 Hz
Engine power 2000 W 2000 W
Force 7 ton 8 ton
Engine type electric electric
Engine model KS ECO 2100 KS ECO 2100
Max. Length 520 mm 520 mm
Max. Diameter 300 mm 350 mm
Cycle time ~ 10 sek. ~ 2 sek.
Operating position horizontal horizontal
Flywheel speed -400 U/min
Cable length 1.85 m 1.7 m
Electric motor winding copper copper
Wheels 6’’ 8’’
Gross dimensions (LxWxH) 980x270x520 mm 1270x340x780 mm
Gross weight 49 kg 130 kg
Protection class IP54M IP54M
Connect the mains lead to a standard 230V±10% (50Hz ±1Hz) electrical supply which has under-voltage,
over-voltage and over-current protection devices as well as a residual current device (RCD) with a maximum
residual current rated at 0.03A.
The diameter of the log is not the only factor that deter-
mines how easy it is to split. A small log may be dicult
to split if it has knots or is a particularly hard wood.
NOTICE
MAIN OVERVIEW HYDRAULIC LOG SPLITTER KS 7THE 52/30 3
Check these components according to the following list and Figure 1 below:
A. Log Guiding Plates
B. Log Pusher
C. Operating Handle Assembly
D. Wheel and Frame
E. Oil Pump
F. Electrical Motor Switch
G. Electrical Motor Assembly
H. Supporting Feet
I. Main Body
J. Splitting Wedge
Fig. 1
www.ks-power.de/en |3

KINETIC LOG SPLITTER KS 8TKE 52/35
CONTROLS AND FEATURES 3.1
9
10
1
5
678
2
3
4
1. Safety Level
2.Engagement Handle
3. Belt Guard
4. Splitting Wedge
5. Ram
6. Cradle
7. Frame Stand
8. Handle
9. Belt
10. Flywheel
LOG SPLITTER KS 7THE 52/30 OPERATION 4
1. Plan the work area before using the log splitter. Have
the logs positioned where they can be easily reached.
2. The log splitter accommodates logs up to 52 cm in
length. The log splitter will work most eciently on dry,
seasoned logs.
3. Position the log splitter securely on level ground or on a
secure stand. If necessary stabilise the wheels to prevent
the log splitter from moving during use. If using an exten-
sion cable, do so in a safe way to avoid damaging the ca-
ble or creating a hazard.
4. Before operating the log splitter, the bleed
screws (Fig. 3) should be loosened by 3-4 turns to al-
low the air to go in and out of the oil tank. Re-tighten the
screw when the work is complete or when moving the log
splitter to avoid oil leaks.
5. Always place logs rmly on the main body, lying at
against the log guide plates (Ref A on Fig1). Never attempt
to split a log at an angle and make sure the logs will not
twist or slip whilst being split.
Ensure the splitting wedge (Ref J on Fig. 1) and the log
pusher (Ref B on Fig. 1) will make contact with the log
squarely at each end.
6. For reasons of safety the log splitter requires a
two-handed operation. Switch on the electric motor us-
ing the green starting switch (Ref F on Fig. 1). Using both
hands press down on both operating handles (Ref C on
Fig. 1). The log splitter will compress the log, pushing
against the splitting wedge. When the log is split release
both handles – this will allow the log pusher to retract.
Fig. 2
Fig. 3
Fig. 4
Log splitter is supplied without the hydraulic oil. Please
don’t start the engine without lling the sucient
amount of hydraulic oil.
WARNING!
www.ks-power.de/en |4

LOG SPLITTER KS 8TKE 52/35 OPERATION 5
Never force the splitting of a log by sustaining the
hydraulic pressure for more than 5 seconds. Try re-
positioning the log on the splitter.
WARNING!
Press the green button to stop the log splitter. Tighten the screw (Fig. 3) and unplug the appliance when
operation is nished. Re-tighten the screw when the work is complete or when moving the log splitter to
avoid oil leaks.
1. Position your Log Splitter on a flat, dry surface
and chock the Wheels or screw down the Frame
Stand to prevent the Splitter from moving during
use.
2. Make sure the Log Splitter is plugged into a
properly grounded protected outlet.
3. Push the green button.
STOPPING THE MOTORSTOPPING THE MOTOR
Push the emergency stop or red button to shut the Motor off.
STARTING THE MOTORSTARTING THE MOTOR
Unplug the Power Cord when not using the Splitter.
NOTE
Switch
Emergency stop
button
Start button
NOTICE
The kinetic log splitter operates differently than a
hydraulic splitter. Not operating the machine properly
will result in damage to the machine.
This is a high-powered machine, with moving parts op-
erating with high energy. You must operate the machine
safely. Unsafe operation can create a number of hazards
for you, as well as anyone else in the nearby area.
WARNING!
Fig. 6 Fig. 7Fig. 5
All logs should be no longer than rated. Refer to the following photos for the correct and incorrect methods
of splitting logs. Never split a log using an incorrect or unsafe method.
• Do not place your hands on the ends of the log when loading the Log Splitter. This is a very UNSAFE
method and could result in injury to your hands (Figure 5).
• Do not reach or step across the beam while the Log Splitter is running. This is a very UNSAFE method
which could cause personal injury or even death.
• Never attempt to split wood across the grain (Fig. 6). The Log Splitter was not designed for cross-grain
splitting. Doing so could damage the Log Splitter and may cause personal injury.
• Make sure both ends of the log you are splitting are cut as square as possible (Fig. 6). This will prevent the
log from sliding out of position while under pressure (Fig. 7).
Always follow these notices:
• Do not be timid. A rapid movement of the Engagement Handle is necessary for the Rack and Pinion to
engage and disengage fully without damage. www.ks-power.de/en |5

4-5 cm
Hands on Sides
of Wood Fig. 8
• Do not hold the Handle in the forward position
when the Ram stops moving forward. Always pull the
Engagement Handle RAPIDLY to the back (Auto-Retract)
position as soon as the Log is split or when the Ram is
at the end of the stroke or when the Ram stops moving
forward due to a tough log.
1. Place the log on the Log Splitter. Grasp the log on the
sides near the middle of the block (Fig. 8). Center the log,
side-to-side, on the rail of the Log Splitter. Do not place
the log tightly to the cutting knife. The recommended
distance from the cutting knife is 4-5 cm.
The engagement Handle must be held fully in the Split
Position against the hard stop when splitting. Failure to
do so may result in kickback of the Handle.
CAUTION!
2. With one hand, actuate and hold the safety lever
towards you, then RAPIDLY actuate the Engagement
Handle fully towards the Motor until it contacts the
hard stop and hold firmly until the Log is split (Fig. 9).
3. IMMEDIATELY AFTER the log is split, actuate and
hold the Engagement Handle to the Auto-Retract
position to allow the Ram to return. If the Ram stops
before the end of the stroke while splitting a tough
log, quickly actuate the Engagement Handle back to
the Auto-Retract position.
Engagement
Handle
Safety lever
If the Ram stops before the end of the stroke while splitting a tough Log, quickly actuate the Engagement
Handle back to the Auto-Retract position. Let the Ram return and allow the Flywheels to gain momentum
for another full power split.
MAINTAINING THE HYDRAULIC
LOG SPLITTER KS 7THE 52/30 7
Fig. 9
• The Engagement Handle should never be stopped in any location between the fully forward or fully
backward positions.
SHARPENING THE WEDGE AND CLEANING THE GUIDE RAILSHARPENING THE WEDGE AND CLEANING THE GUIDE RAIL
After using the log splitter for some time, sharpen the wedge using a fine tooth file and smooth any burrs
or rough edges along the cutting edge.
Clean the guide rail regularly, especially when splitting wood that is rich in resin.
TO FREE A JAMMED LOG 6
Release both operating handles so that the log pusher is fully
retracted. Insert a triangular wedge of wood under the log and
activate the log pusher to push the wedge under the jammed log.
Repeat this process using progressively larger wedges until the
jammed log is freed.
Never hammer a jammed log or place your hands near
WARNING! the log when attempting to free a jammed
log.
WARNING!
www.ks-power.de/en |6

Fig. 8
LUBRICATIONLUBRICATION
RAIL MAINTENANCERAIL MAINTENANCE
Between each use of the LOG SPLITTER, we recommend
removing any debris caught on the Rail or Ram and applying
a rust preventative (Fluid Film or equivalent) to any bare
metal areas on the top of the Rail (Fig. 10). This will assure
the smoothest return action of the Ram.
MAINTAINING THE KINETIC
LOG SPLITTER KS 8TKE 52/35 8
Before performing any maintenance procedure or
inspection, stop the electric motor, wait five minutes to
allow all parts to cool. Disconnect the power cord from
the source of Electricity.
WARNING!
All Bearings of your Splitter are sealed units and should
have sufficient lubricant to last the life of your machine
with normal use.
WARNING!
Top of Rail
REPLACING HYDRAULIC OILREPLACING HYDRAULIC OIL
Replace the hydraulic oil in the log splitter after every 150 hours of use. Take
the following steps to replace the oil:
1. Make sure all moving parts are stopped and the log splitter is unplugged.
2. Unscrew the oil drain bolt.
3. Turn the log splitter onto the support leg side and hold over a 3 litre
container to drain the oil into.
4. Turn the log splitter vertically to stand on its end with the motor underneath
and the operating handles uppermost.
5. Fill with fresh hydraulic oil. As stated in the Specifications Table on
page 5 the correct oil capacity is 2.9L.
6. Clean the surface of the dipstick, which is attached to the oil drain bolt,
with a clean lint free cloth and put back into the tank to check the new level.
Make sure the level of the refilled oil is just between the two grooves around
the dipstick.
7. Clean the oil drain bolt before screwing it back. Make sure it is tightened to
avoid leakage before placing the log splitter horizontally.
Periodically check the oil level to ensure it is between the
two grooves on the dipstick. Refill when the oil reaches
the lower level.
NOTICE
Use hydraulic oilI SO VG 22.
The following hydraulic oils or equivalent are recommended for the log splitter’s hydraulic transmission
system:
- SHELL Tellus 22
- MOBIL DTE 11
- ARAL Vitam GF22
- BP Energol HLP-HM22
It is important to grease the Rack every
5 hours for proper operation.
NOTE
GREASING THE RACKGREASING THE RACK
Fig. 10
TOOLS AND SUPPLIES NEEDED:TOOLS AND SUPPLIES NEEDED:
• General Purpose Grease • Clean Rags • 13mm Wrench
www.ks-power.de/en |7

Fig. 12
1. Use a 13 mm wrench to remove the Guard Screws that secure the flywheel Guard (Fig 11).
2. Remove the Guard Screws that secure the Flywheel and Belt Guard.
3. Disconnect the return spring.
4. Pull the Rack out and grease the Rack Teeth, top side of the Rack and the Pinion (Fig.12).
5. Push the Rack back in and reinstall the Return Spring when finished greasing.
6. Reinstall the Guards.
Guard
Screws
flywheel
Guard
Guard
Screws
Belt Guard
Pinion
Rack Teeth
Fig. 11
REGULAR MAINTENANCE CHECKLIST 9
This manual compliance! You can find a list of service center addresses on the website of exclusive importer:
www.ks-power.de/en
Potential faults and troubleshooting methods can be found in the full version of the manual.Potential faults and troubleshooting methods can be found in the full version of the manual.
WARRANTY SERVICE TERMS 10
The international manufacturer warranty is 1 year. The warranty period starts from the date of purchase.
In cases when warranty period is longer than 1 year according to local legislation please contact your local
dealer.TheSellerwhichsellstheproductisresponsibleforgrantingthewarranty.PleasecontacttheSellerfor
warranty. Within the warranty period, if the product fails because of defects in the production process, it will
be exchanged on the same product or repaired.
The warranty card should be kept throughout the warranty period. In case of warranty card loss, a second
one will not be provided. The customer must provide the warranty card and buyer`s check during request
for repair or exchange. Otherwise, the warranty service will not be provided. The warranty card, attached to
the product during sale, should be correctly and fully completed by the retailer and customer, signed and
stamped. In other cases, warranty is not considered as valid.
Provide clean product to the service center. Parts, that must be replaced, are the property of the service
center.
PROCEDURE Before each use Every 5 hours Every 25 hours Every 150 hours
Check general equipment
condition
Cleaning the rail from
debris
Check belt
KS 8TKE 52/35
Check the condition of the
electrical cord
Grease rack
Clean motor exterior and
cooling ns
Motor oil changing KS 7THE 52/30
www.ks-power.de/en |8

Fig. 12

CONTACTS
Deutschland:
DIMAX International GmbH
Deutschland, Hauptstr. 134,
51143 Köln,
www.ks-power.de
Ihre BestellungenIhre Bestellungen
[email protected]
Kundendienst, technischeKundendienst, technische
Fragen und UnterstützungFragen und Unterstützung
[email protected]
Garantie, Reparatur undGarantie, Reparatur und
ServiceService
[email protected]
SonstigesSonstiges
[email protected]
Polska:
DIMAX International
Poland Sp.z o.o.
Polen, Warczawska, 306B
05-082 Stare Babice,
www.ks-power.pl
[email protected]
Україна:
ТОВ «Техно Трейд КС», вул.
Електротехнічна 47, 02222,
м. Київ, Україна
www.ks-power.com.ua
[email protected]
Россия:
ТД «Рус Энержи К&С» 129090,
г.Москва, проспект Мира,
д.19, стр.1, эт.1, пом.1,
комн.6б, офис 99В
www.ks-power.ru
[email protected]