TK MVP-90 User manual

1
Operator’s Safety and Service Manual
Plate Compactor
MVP-90
It is the OWNER´S RESPONSABILITY to communicate information on the
SAFE USE and OPERATION of this machine to the operators.
27112013
Discount-Equipment.com

2
TABLE OF CONTENTS
1.Serial Number Location.............................................. 3
2.Parts Ordering Procedure .......................................... 3
3.Assembling Instructions ............................................. 4
4.Safety Precautions ..................................................... 4
5.Safety Notice & Decals ............................................... 5
6.Before Operating........................................................ 9
7.Starting Engine ......................................................... 10
8.Operating Instructions ............................................. 11
9.Service Instructions.................................................. 12
10.Maintenance Schedule .......................................... 14
11.Replacements......................................................... 14
12.Torque Chart .......................................................... 15
13.Warranty ................................................................ 16
14.Warehouse Locations............................................. 17
15.Notes...................................................................... 18
16.Parts List Breakdown....................................Attached
Discount-Equipment.com

3
1. SERIAL NUMBER LOCATION
The model/serial number decal is located on the shroud assembly (black).
(Write model number)
(Write serial number)
The unit’s year of manufacture can be determined by the serial number. Contact your nearest
sales branch or for more information.
This Unit warranty is stated in this Operational and Safety manual on page 16. Failure to
return warranty registration card renders the warranty null and void.
An engine owner’s manual is also attached to every unit. Engine parts may order from any
authorized dealer. Refer to the engine owner´s manual lo learn about specifications and part
identification.
2. PARTS ORDERING PROCEDURE:
Parts are available worldwide and must be ordered through your local distributor. If you
can’t locate the distributor in your area refer to page 17 of this manual to locate the
nearest branch and contact numbers for assistance.
Grinders are intended for use in several applications. They are powered by four stroke
gas engines or electric motors and are available in different sizes and manufacturers.
This Operation manual contains only standard parts. Variations of these parts as well as other
special parts are not included. Contact your local distributor for assistance in identifying
parts not included in this manual.
ALWAYS HAVE READY:
1. Model and serial number of machine when ordering parts.
2. Model and serial number of engine when ordering engine parts.
3. Item part number(S), description, and quantity.
4. Company name, address, zip code, and purchase order number.
Discount-Equipment.com

4
5. Preferred method of shipping.
REMEMBER –You own the best. If repairs are needed, use
only purchased parts from authorized distributors.
3. ASSEMBLING INSTRUCTIONS
UNPACKING
1. Remove the unit and all components from its shipping crate. You will see:
Preassembled Plate Compactor
FINAL ASSEMBLING
Plate Compactors are shipped completely assembled almost for immediate use, just
lubricants and oil are needed to start the engine.
Note: All installation hardware must be inserted into its respective location on the
equipment, see parts explosion for more details.
1. Using appropriated equipment, bring the unit to the ground from its shipping pallet.
Warning: failure to use proper lifting equipment could cause
the equipment to fall and cause serious injury.
4. SAFETY PRECAUTIONS
READ AND STUDY THE FOLLOWING SAFETY INFORMATION BEFORE ATTEMPTING TO OPERATE THIS
EQUIPMENT. IN ADDITION, ENSURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH
THIS EQUIPMENT IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
WARNING - LETHAL EXHAUST GAS!
An internal combustion engine discharges carbon monoxide, which is a poisonous and odorless
invisible gas. Death or serious illness may result if inhaled. Operate only in an area with good
ventilation, NEVER IN A CONFINED AREA!
WARNING - DANGEROUS FUELS!
Use extreme caution when storing, handling and using fuels - they are highly volatile and explosive in
the vapor state. Do not add fuel while engine is running. Stop and cool the engine before adding fuel.
DO NOT SMOKE WHEN REFUELING!
SAFETY GUARDS
It is the owner's responsibility to ensure ALL GUARDS AND SHIELDS are in place and in working order.
Discount-Equipment.com

5
IGNITION SYSTEMS
Breakerless magneto and batteries ignition systems CAN CAUSE SEVERE ELECTRICAL SHOCKS, avoid
contact with these components or their wiring.
SAFE DRESS
DO NOT WEAR loose clothing, rings, wristwatches, etc., near machinery.
NOISE PROTECTION
Wear O.S.H.A. specified hearing protection devices.
FOOT PROTECTION
Wear O.S.H.A. specified steel tip safety shoes.
HEAD PROTECTION
Wear O.S.H.A. specified safety helmets.
EYE PROTECTION
Wear O.S.H.A. specified eyes shields, safety glasses, and sweat bands.
DUST PROTECTION
Wear O.S.H.A. specified dust mask or respirator.
OPERATOR
Keep children and bystanders off and away from the equipment. Only trained Operators who fully
understand its safety operation must use this equipment.
For details on safety rules and regulations in the United States, contact your local Occupational Safety
and Health Administration (O.S.H.A.) office. Equipment operated in other countries must be operated
and serviced in accordance and compliance with any and all safety requirements of such country. The
publication of these safety precautions is done for your information does not by the publication of
these precautions, imply or in any way represent that these are the sum of all dangers present near
equipment. If you are operating a unit it is your responsibility to insure that such operation is
in full accordance with all applicable safety requirements and codes. All requirements of the United
States Federal Occupational Safety and Health Administration Act must be met when operated in
areas that are under the jurisdiction of that United States Department.
5. SAFETY NOTICE & DECALS
IMPORTANT NOTICE
The "SAFETY ALERT SYMBOL" is used to call attention to items or operations that may be
dangerous to those operating or working with this equipment. These symbols can be found
throughout the manual and on the unit itself. Please read these warnings and cautions carefully.
Discount-Equipment.com

6
READ SAFETY DECALS CAREFULLY
Carefully read and follow all safety decals. Keep them in good conditions. If they become
aged, replace as required. If repainting, REPLACE ALL decals. Decals are available from your
authorized Distributors. Decals are not shown to scale.
201155
201157
IMPORTANT NOTICE
The "SAFETY ALERT SYMBOL" is used to call attention to items or operations that may be
dangerous to those operating or working with this equipment. These symbols can be found
throughout the manual and on the unit itself. Please read these warnings and cautions carefully.
Discount-Equipment.com

7
READ SAFETY DECALS CAREFULLY
Carefully read and follow all safety decals. Keep them in good condition. If they become aged,
replace as required. If repainting, REPLACE ALL decals. Decals are available from your
authorized Distributors. Decals are not shown to scale.
201003 (x2)
201005
201026
201152
201005
201006
201001 BIG
201001 SMALL
290791
201004
201154
Discount-Equipment.com

8
SAFETY PRECAUTIONS
!
DANGER
EXPLOSION HAZARD
Never operate the machine in an
explosive atmosphere, near
combustible materials or where
ventilation does not clear exhaust
fumes.
!WARNING
BURN HAZARD
Never come into contact with the
engine or muffler when engine is
operating or shortly after it is turned
off. Serious burns may occur
!CAUTION
MOVING PARTS
Before starting the machine ensure
that all guards and safety devices
are in place and functioning
properly.
!CAUTION
MACHINE DAMAGE
Advance cutter depth in small
increments to avoid premature
wear or damage.
!ATTENTION
READ OWNERS MANUAL
Read and understand operator's
manual before using this machine.
Failure to follow operating
instructions could result in serious
injury or death.
Discount-Equipment.com

9
6.BEFORE OPERATING
REMEMBER! It is the owner´s responsibility to communicate information on the safe
use and proper operation of this unit to the operators.
Before operating, review SAFETY PRECAUTIONS listed on page 6 of this manual.
Familiarize yourself with the operation of the unit and confirm that all controls
function properly BEFORE starting engine.
Locate the killing switch and assure you know how to STOP the unit.
Make sure hands, feet, and clothing are at a safe distance from any moveable parts
prior to starting.
Shrouds and guards are provided to protect the operator or structures in close
proximity to rotating hot engine parts. It is the RESPONSABILITY OF THE OPERATOR to
see that they are properly in place. NEVER operate this equipment without a guard.
OIL LEVEL - Check the oil level in the engine. For more information see "Lubrication"
under the engine "Owner's Manual" the "Maintenance" section of this manual. All
Equipment come without oil, running an engine without lubrication may damage the
engine.
AIR CLEANER - Check to ensure elements are in good condition and properly installed.
Review every decal with the OPERATOR.
FUEL SUPPLY - Engines on equipment require an automotive grade of clean, fresh,
unleaded or regular gasoline. All equipment’s come without gasoline and oil.
FUEL FILTER - Check to ensure element is in good condition... Replace if it is clogged or
damaged.
SPARK PLUG (GAS UNIT) –Check and clean spark plugs regularly. A fouled, dirty or
carbonated spark plug may cause difficulties starting and poor engine performance.
Set spark plug gap to recommended clearance. Refer to engine manual.
POSITION –The only operating position for this grinder is at the rear of the equipment.
If the operator must leave this position the engine must be shut down.
SPECTATORS –Keep all personnel/spectators away from the Grinder while running.
This spinning equipment can throw segments and can cause injuries.
Discount-Equipment.com

10
7. STARTING ENGINE/AIR
GAS ENGINE
1. With the Plate Compactor engine level in the ground check oil level and add oil
and fuel as required.
2. Pull the stop switch on the unit to its "Out" position.
3. Move the engine throttle control to the "FAST" position.
4. Choke the engine if necessary. (You may not need to choke a warm engine)
BEFORE STARTING ENGINE MAKE SURE ALL GUARDS ARE IN PLACE.
5. Pull the starter string.
6. After the engine starts, move the choke lever to the open position, move the
throttle level to the "IDLE" position and let the engine warm-up for one or two
minutes.
To stop the engine, make sure to let the engine idle before stopping by using
the crank lift handle to raise the grinder cutters height.
7. Push in the engine stop switch on the equipment.
8. Close the fuel valve.
ELECTRIC MOTOR
1. With the cage in maximum raised position, plug the motor into a suitable power
source.
2. Move the switch on the motor to the "ON" position.
STOP THE ENGINE OR ELECTRIC MOTOR BEFORE:
Adding fuel.
Leaving equipment unattended for any amount of time.
Making any repairs or adjustments to the unit.
Lifting/Transportation.
Discount-Equipment.com

11
8.OPERATION INSTRUCTIONS
1. Once the engine has started, move the engine throttle lever quickly to the FAST
position. With the throttle lever in the fast position, the engine speed should be
around 2,300 RPM, which engages the centrifugal clutch.
2. Firmly gasp the compactor's handle bar with both hands as the compactor begins
moving forward.
3. Slowly walk behind the compactor and be on the lookout for any large objects or
foreign matter that might cause damage to the compactor or bodily injury.
4. Compactor traveling speed may drop on soils which contain clay, or other types of
soil. Soil with high moisture content can cause the compaction plate to "stick" to the
ground (not lifting up off the ground very fast or high). To rectify this problem,
consider the following:
Check the bottom plate to see if clay or equivalent material has been
lodged in the plate mechanism. If so, wash with water and remove.
Remember the compactor does not work as efficiently on clay or soils
that have a high moisture content level.
If the soil has a high moisture level, dry soil to appropriate moisture
content level or carry out compaction twice.
5. The MVC-90H is equipped with a watering system that can be used to wet the ground
during compaction to keep dust levels down.
NEVER FORCE THIS EQUIPMENT INTO THE SURFACE TO A POINT WHERE THE
EQUIPMENT STARTS BOUNCING
6. If the power source fails, raise the compactor off of the floor. Disconnect power
source, inspect accessories for damage. Replace damage (or questionable)
accessories before re-staring the equipment.
7. When transporting the compactor, disconnect the power source before lifting or
removing any guard.
8. When hosting or lifting grinder, always inspect frame and attaching hardware for
damage before lifting. Use proper safer hoisting and lifting equipment to prevent
injuries.
Discount-Equipment.com

12
9. SERVICE INSTRUCTIONS
Never service or lubricate the unit engine while running.
After servicing the unit, restore and fasten all guards, shields, and covers to their
original positions.
Never drain oil into the ground, into open streams, or down sewage drains.
Keep air filter clean at all times. Wash away dust and debris using anon-oil based
cleaning solvent. Let the filter dry before re- installing.
WHEN LIFTING/LOWERING ALWAYS:
1. Set the machine in an upright position.
2. Stop the engine or electric motor.
3. Secure hardware on the machine.
4. Make sure you use appropriated lifting equipment to lift equipment.
5. Do not position yourself where you could possibly be pinched / caught between
the equipment and some other obstacle.
TOWING
1. Do not tow the unit with another vehicle. The grinder may be damage if towed.
STORING
1. Drain fuel tank.
2. Run the engine until the fuel in the injection system is completely consumed.
3. Clean drive shaft, threats. Coat parts with grease.
4. Lube all bearings
5. Empty water system
6. Clean all moving parts with WD-40 lubricant.
7. Lower unit completely.
8. Cover unit for protection.
ENGINE
See engine owner´s manual maintenance schedule.
SPARK PLUG
1. Check and clean spark plugs regularly. A fouled, dirty or carbonized spark plug
causes hard starting and poor engine performance. Set spark plug gap to
recommended clearance. Refer to engine manual.
Discount-Equipment.com

13
BELT TENSION
1. If there is excessive belt play, there will be a decrease in the grinding action,
which could cause cage and machine damage. The normal belt play should be
3/8” to 1/2” which is attained by depressing the top section of the belt at the
belt guard mounting bracket location. When adjusting the belt make sure that
the drive pulley is in alignment with cage pulley. Tighten all engine mount bolts,
adjust the two engine-stop bolts, and tighten lock nuts.
REPLACING V-BELT/CLUTCH
1. Remove the belt cover.
2. Place an offset wrench (13 mm) or the like on the vibrator pulley (lower)
Fastening bolt.
3. Using a waste cloth or the like, pull the V-belt back strongly at midway of the
belt on the left side and rotate the offset wrench clockwise so that the V-belt
will come off.
4. Check the clutch and replace as necessary, following the procedures listed in
Checking the Clutch.
5. Place the V-belt on the lower vibrator pulley. Push the V-belt to the left side of
the upper clutch and rotate the offset wrench clockwise so that the V-belt
moves onto the pulley.
REPLACING CLUTCH
6. With belt cover removed, visually check outer drum of the clutch for seizure
and "V" groove for wear or damage.
7. Clean the "V" groove as necessary.
8. Check the clutch lining and shoe for signs of wear. If the shoe is worn, replace
the clutch to prevent deficient power transmission and slippage.
9. If Clutch must be replaced, first remove V-belt.
10. Remove bolt at engine power output by tapping an engaged wrench (e.g.
tapping with hammer) and rotate the bolt counterclockwise.
11. Remove clutch with a pulley extractor.
12. To install a new clutch, reverse steps 1-3.
Discount-Equipment.com

14
10. MAINTENANCE SCHEDULE
1. Check all hardware after the first 5 hours of use, the follow the maintenance schedule.
Maintenance
Services Intervals
After
every use
After 45
days or
50 hrs.
Every 3
months
or
100 hrs.
Every 6
months
or
200 hrs.
Every 9
months
or
300 hrs.
Every 12
months
or
400 hrs.
General Inspection:
Guards
Check
X
X
X
X
X
Warning stickers
Check
X
X
X
X
X
Test run
Check operation
X
X
X
X
X
V-belt & Clutch
Check
X
X
X
Engine:
Engine oil
Check level
X
X
X
X
X
X
Change
X
X
X
Engine oil filter
Replace
X
X
Oil cooler
Clean
X
X
X
X
Cooling Fins
Clean
X
X
X
X
X
Air cleaner
Check - clean
X
X
X
X
X
X
Replace
X
Air Intake Line
Check
X
Replace
2 years
Fan Belt
Check tightness
X
X
Replace
500 hrs.
Valve clearance
Check-adjust
X
X
Fuel filter
Check & clean
X
X
X
X
Replace
X
X
Fuel Tank
Clean
500 hrs.
Engine wiring
Check
X
11. REPLACEMENTS
Parts
Tolerance or Replacement Cycle
Engine Components
Refer to your engine manufacturer´s Owner´s
Manual
V-Belts
Replace if stretched to the point that the idler does
not work properly. Replace the V-belts if they are
cracked or torn.
Hardware
Re-torque all bolts after the first eight hours of
operation and check hardware every 25 hours.
Replace any worn or damaged hardware as
needed. Replacement hardware should be grade 5
and zinc plated.
Safety Decals
Replace if they become aged, damaged or cannot
be easily read.
Discount-Equipment.com

15
12. TORQUE CHART
Discount-Equipment.com

16
13. WARRANTY
THIS IS YOUR WARRANTY –PLEAE READ AND SAVE
1. TK Equip warrants each new machine against any manufacturing defect in material and workmanship
under normal use and service for a period of (1) one year. Warranty period begins on first day of use by end
user. This first day of use is established by the date of a completed warranty card or a bill of sale to the end
user.
2. The obligation under this warranty is limited to the replacement of parts at your TK Equip factory branch
or on an authorized TK Equip distributor.
3. Machines altered or modified without a TK Equip written consent may void this warranty policy
immediately. Misuse, negligence, accidents or the operation of the machines in any other way that the
recommended by TK Equip operation procedures, will void this warranty policy. This warranty shall not
apply to machines repaired by other than authorized TK Equip branches or distributors.
4. The cost of transportation and other expenses related are not covered by this warranty.
5. Written authorization for the return of merchandise under warranty must be obtain from TK Equip
customer service contact. All equipment & parts returned may be sent with a signed RGA (Return Goods
Authorization) for its follow up.
6. TK Equip reserves the right to inspect and render the final decision on each warranty case.
7. TK Equip reserves the right to improve or make product changes without incurring any obligation to
update, refit or install on machines previously sold.
8. TK Equip is not responsible for any liability, damage or injury directly or indirectly from the design,
material or operation of its product.
9. The warranty letter must be returned to TK Equip within 10 days after purchase/adquire, for a first use
failure warranty claim.
10.Warranty request must be submitted in written within 30 days after machine failure to TK Equip customer
service.
11. THE FOREIGN WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR USE AND OF ALL OTHER
OBLIGATION OR LIABILITIES ON OUR PART, AND WE NEITHER ASSUME NOR AUTHORIZE AINES, MOTOR
AND THEIR COMPONENTS.NY OTHE RPERSON TO ASSUME FOR US ANY OF OUR PRODUCTS . LIKEWISE, THIS
WARRANTY
Discount-Equipment.com

Discount-Equipment.com is your online resource for commercial and industrial
quality parts and equipment sales.
Locations:
Florida (West Palm Beach): 561-964-4949
Outside Florida TOLL FREE: 877-690-3101
Need parts? Check out our website at www.discount-equipment.com
Can’t find what you need?
Click on this link: http://www.discount-equipment.com/category/5443-parts/ and fill out
the request form.
Please have the machine model and serial number available in order to help us get
you the correct parts. One of our experienced staff members will get back to you with
a quote for the right part that your machine needs.
We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mayco, Toro/Stone,
Diamond Products, Magnum, Airman, Mustang, Power Blanket, Nifty Lift, Atlas Copco,
Chicago Pneumatic, Allmand Brothers, Essick, Miller Spreader, Skyjack, Lull, Skytrak,
Tsurumi, Husquvarna/Target, Whiteman-Concrete/Mortar, Stow-Concrete/Mortar, Baldor,
Wacker, Sakai, Snorkel, Upright, Mi-T-M, Sullair, Neal, Basic, Dynapac, MBW, Weber,
Bartell, Bennar Newman, Haulotte, Ditch Runner, Blaw-Knox, Himoinsa, Best, Buddy,
Crown, Edco, Wyco, Bomag, Laymor, Terremite, Barreto, EZ Trench, Takeuchi, Basic, Bil-
Jax, Curtis, Gehl, Heli, Honda, ICS/PowerGrit, Puckett, Waldon, ASV, IHI, Partner, Imer,
Clipper, MMD, Koshin, Rice, Gorman Rupp, CH&E, Cat Pumps, Comet, General Pump,
Giant,AMida, Coleman, NAC, Gradall, Square Shooter, Kent, Stanley, Tamco, Toku, Hatz,
Kohler, Robin, Wisconsin, Northrock, Oztec, Toker TK, Rol-Air, Small Line, Wanco, Yanmar
Discount-Equipment.com

18
15. NOTES:
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
Discount-Equipment.com