Insinger N-8 User manual

DESIGN
Rugged Series N disposer with an 8” rotor is designed primarily for
installation in the vegetable and salad preparation area of a medium
to large kitchen. It is also ideal for handling of the general waste in
a small restaurant. Equipped with a 2 HP motor as standard, this
unit is also recommended for use in disposing of the waste from a
potato peeler. If the general waste is rather heavy use of the 3 HP
motor is recommended. 3 HP is also correct for use in the pot wash
area where peak work loads are always greater than anticipated,
making added motor strength a requirement. The 1 1/2 HP motor is
satisfactory for use in smaller kitchens where the waste is light.
SERIES N 8” ROTOR
COMMERCIAL FOOD WASTE DISPOSER
STANDARD EQUIPMENT
• 2 HP motor
6245 State Road
Philadelphia, PA 19135-2995
215-624-4800
215-624-6966 FAX
800-344-4802
www.insingermachine.com
OPTIONAL EQUIPMENT
• Stainless steel cone or sink attachment (includes vinyl silver trap
ring, solenoid valve, flow control valve, vacuum breaker)
• 1 1/2 HP motor- lighter duty
• 3 HP motor- heavier duty
• Offset-body for maximum space utilization, also available for both
cone & sink attachments
• Cones 12”, 15” & 18”
NOTE: Sink attachments and s/s cones need to be welded into table
O style- Optional off-set body
for use with bowl/cone trough

Note: For all rough in connections see Installation and Layout Detail Drawing
N-8 DISPOSER
DESIGN AND CONSTRUCTION
• Waste chamber design permits dual directional operation when used with reversing control or switch, doubling the life
cycle of the shattering mechanism. Regular waste chamber available with either 4 1/2” or 7” throat size.
• Basic body components are cast gray iron, machined, primed and painted. 8” diameter rotor with (2) bolt-on
reversible impact bars and sizing ring are cast ductile iron, machined, balanced and heat treated.
• Flexible drain connector. Fastens quickly to either metal or PVC drain line (2” pipe size).
• Stainless steel legs and feet, adjustable from 0” to 2”.
• Disposer connects to cone or sink assembly by means of a neoprene isolation sleeve and (2) stainless steel clamps.
• Offset Design: For maximum space utilization, disposer is also available with an 8” off-set waste chamber for both
cone and sink attachments. (Available with 7” diameter throat size only.)
MOTOR
• Reversing, continuous duty, 1725 RPM (1425 RPM, 50 Hz), full rated horsepower, double sealed, permanently
lubricated ball bearings.
• Thermal overload protection with manual reset button.
• Available for single phase or three phase installations.
• Available in 1 1/2 HP for light waste, 2 HP for standard use, 3 HP for heavy duty use.
• Dual voltage windings allow multi-voltage operation by motor lead connection. (See motor wiring diagram)
115-230 Volts, 60Hz; 110/220 Volts, 50 Hz, 1 Phase
208-230/460 Volts, 60 Hz; 190-220/380-440 Volts, 50 Hz, 3 Phase
(See table for ampere draw per horsepower, volts & phase)
CONTROLS
Electrical switches or control centers not included, must be selected as required.
Note: All plumbing and electrical connections should be made according to local codes.
HP SINGLE PHASE THREE PHASE
Volts Amps* Volts Amps*
1 1/2 115
230 17.2 8.6
208
230
460
4.9
4.4
2.2
2115
230 18.4 9.2
208
230
460
6.9
6.2
3.1
3 NA 208 230
460
9.7
8.8
4.4
*Ratings are for 60 Hz operation.
1” Min.
6” Max.
1” Min.
6” Max. 1” Min.
6” Max.
1” Min.
6” Max.
Disposer shown with regular 7” drum
and sink mounting assembly Note: All dimensions shown at 0” foot height adjustment
8” length of neoprene connector
sleeve furnished. May be cut to
desired length.
Adjustable 0” to 2”
Disposer shown with offset drum and
cone mounting assembly
4 1/2” regular drum with
sink mounting assembly
Table Cutout
13” for 12” cone
16” for 15” cone
19” for 18” cone
1” 5” for 12” cone
6” for 15” cone
7” for 18” cone 1”
1”
1”
4 1/2”
6 1/4”
8”
14 1/2”
27”
8”
7”
5” for 12” cone
6” for 15” cone
7” for 18” cone
6 1/4” 8” Adjustable 0” to 2”
19”
23” 14 1/2”
7”
8”
Water
inlet
Drain
4 1/2” regular drum with
cone mounting assembly
Drain
Cutout 5 1/2”
4 1/2” inside
diameter