TMG TMG-WC62S User manual

www.tmgindustrial.com TOLL FREE: 1-877-761-2819
6“ SKID STEER
WOOD CHIPPER
PRODUCT MANUAL
v.2023.02.20
TMG-WC62S

www.tmgindustrial.com 2 / 22 TOLL FREE: 1-877-761-2819
CONTENTS
IMPORTANT SAFETY INFORMATION ......................................................................................................................................... 3
YOUR SAFETY ............................................................................................................................................................................. 3
GENERAL SAFETY ....................................................................................................................................................................... 3
EQUIPMENT SAFETY GUIDELINES ................................................................................................................................................. 4
SAFETY TRAINING ....................................................................................................................................................................... 5
SAFETY SIGNS ............................................................................................................................................................................ 5
PREPARATION ............................................................................................................................................................................. 6
MAINTENANCE SAFETY ............................................................................................................................................................... 6
HYDRAULIC SAFETY .................................................................................................................................................................... 7
TRANSPORT SAFETY ................................................................................................................................................................... 7
TO THE NEW OPERATOR OR OWNER ............................................................................................................................................ 8
OPERATION ............................................................................................................................................................................ 8
MACHINE COMPONENTS ............................................................................................................................................................. 8
MACHINE BREAK-IN ................................................................................................................................................................... 9
PRE-OPERATION CHECKLIST ...................................................................................................................................................... 9
MACHINE SET-UP .................................................................................................................................................................... 10
HYDRAULIC CONNECTIONS &MOUNTING .................................................................................................................................. 10
CHIPPING OPERATION ............................................................................................................................................................... 12
UNPLUGGING ............................................................................................................................................................................ 13
SEVERE PLUG ........................................................................................................................................................................... 13
MAINTENANCE ..................................................................................................................................................................... 14
BLADE AND BREAKER MAINTENANCE ........................................................................................................................................ 14
ROTOR BLADES MAINTENANCE ................................................................................................................................................. 14
LEDGER BLADES MAINTENANCE ................................................................................................................................................ 15
HYDRAULIC SYSTEM ................................................................................................................................................................. 15
BOLT TORQUE ........................................................................................................................................................................... 15
SPECIFICATION .................................................................................................................................................................... 16
SPECIFICATIONS &CAPACITIES ................................................................................................................................................ 16
PARTS LIST ......................................................................................................................................................................... 17
WOOD CHIPPER ASSEMBLY ....................................................................................................................................................... 17
HYDRAULIC COMPONENTS ......................................................................................................................................................... 19
ROTOR ASSEMBLY .................................................................................................................................................................... 20
DISCHARGE CHUTE ASSEMBLY .................................................................................................................................................. 21
INFEED HOPPER ASSEMBLY ....................................................................................................................................................... 22

www.tmgindustrial.com 3 / 22 TOLL FREE: 1-877-761-2819
IMPORTANT SAFETY INFORMATION
Your Safety
YOU are responsible for the SAFE operation and maintenance of your TMG Skid Steer Wood Chipper. YOU must ensure that you
and anyone else who is going to use, maintain or work around the Skid Steer Wood Chipper be familiar with the using and
maintenance procedures and related SAFETY information contained in this manual. This manual will take you step-by-step
through your working day and alerts you to all good safety practices that should be used while using the Skid Steer Wood
Chipper.
Remember, YOU are the key to safety. Good safety practices not only protect you but also the people around you. Make these
practices a working part of your safety program. Be certain that EVERYONE using this equipment is familiar with the
recommended using and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do
not risk injury or death by ignoring good safety practices.
1. Skid Steer Wood Chipper owners must give operating instructions to operators or employees before allowing them to
operate the machine, and at least annually thereafter.
2. The most important safety device on this equipment is a SAFE operator. It is the operator’s responsibility to read and
understand ALL Safety and Operating instructions in the manual and to follow these. Most accidents can be avoided.
3. A person who has not read and understood all using and safety instructions is not qualified to use the machine. An untrained
operator exposes himself and bystanders to possible serious injury or death.
4. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect
the life of the equipment.
5. Think SAFETY! Work SAFELY!
General Safety
1. Read and understand the Operator’s Manual and all safety signs before using, maintaining, adjusting, or cleaning the Skid
Steer Wood Chipper.
2. Have a first-aid kit available for use should the need arise and know how to use it.
3. Have a fire extinguisher available for use should the need arise and know how to use it.
4. Do not allow riders.
5. Wear appropriate protective gear. This list includes but is not limited to:
- A hard hat
- Protective shoes with slip resistant soles
- Heavy gloves

www.tmgindustrial.com 4 / 22 TOLL FREE: 1-877-761-2819
- Wet weather gear
- Hearing Protection
6. Install and secure all guards before starting.
7. Wear suitable ear protection for prolonged exposure to excessive noise.
8. Turn machine off, stop and disable engine, remove ignition key and place in your pocket, set park brake and wait for all
moving parts to stop before servicing, adjusting, repairing, or unplugging.
9. Clear the area of people, especially small children, before using the unit.
10. Review safety related items annually with all personnel who will operating or maintaining the Skid Steer Wood Chipper.
Equipment Safety Guidelines
1. Safety of the operator and bystanders is one of the main concerns in designing and developing equipment. However, every
year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to
handling equipment. You, the operator, can avoid many accidents by observing the following precautions in this section. To
avoid personal injury or death, study the following precautions and insist those working with you, or for you to follow them.
2. In order to provide a better view, certain photographs or illustrations in this manual may show an assembly with a safety
shield removed. However, equipment should never be used in this condition. Keep all shields in place. If shield removal
becomes necessary for repairs, replace the shield prior to use.
3. Replace any safety sign or instruction sign that is not readable or is missing. Location of such safety signs is indicated in
this manual.
4. Never use alcoholic beverages or drugs which can hinder alertness or coordination while using this equipment. Consult
your doctor about using this machine while taking prescription medications.
5. Under no circumstances should young children be allowed to work with this equipment. Do not allow persons to use or
assemble this unit until they have read this manual and have developed a thorough understanding of the safety
precautions and of how it works. Review the safety instructions with all users annually.
6. This equipment is dangerous to children and persons unfamiliar with its operation. The operator should be a responsible,
properly trained and physically able person familiar with machinery and trained in this equipment's operations. If the
elderly are assisting with work, their physical limitations need to be recognized and accommodated.
7. Never exceed the limits of a piece of machinery.
8. If its ability to do a job, or to do so safely, is in question - DON'T TRY IT.
9. Do not modify the equipment in any way. Unauthorized modification may result in serious injury or death and may impair
the function and life of the equipment.

www.tmgindustrial.com 5 / 22 TOLL FREE: 1-877-761-2819
10. In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment, hazard control
and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved
in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation
instruction in each of the appropriate sections of the skid steer and machine manuals. Pay close attention to the Safety
Signs affixed to the skid steer and the machine.
Safety Training
1. Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe
equipment can be wiped out by a single careless act of an operator or bystander.
2. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the
awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and
storage of this equipment.
3. It has been said, "The best safety feature is an informed, careful operator." We ask you to be that kind of an operator. It is
the operator's responsibility to read and understand ALL Safety and Using instructions in the manual and to follow these.
Accidents can be avoided.
4. If this machine is used by any person other than yourself, or is loaned or rented, it is the machine owner's responsibility to
make certain that the operator, prior to using:
a. Reads and understands the operator's manuals.
b. Is instructed in safe and proper use.
5. Know your controls and how to stop the skid steer tractor and machine quickly in an emergency. Read this manual and the
one provided with skid steer tractor.
6. Train all new personnel and review instructions frequently with existing workers. Be certain only a properly trained and
physically able person will use the machinery. A person who has not read and understood all using and safety instructions
is not qualified to use the machine. An untrained operator exposes himself and bystanders to possible serious injury or
death. If the elderly is assisting with the work, their physical limitations need to be recognized and accommodated.
Safety Signs
1. Always keep safety signs clean and legible.
2. Replace safety signs that are missing or have become illegible.
3. Replaced parts that displayed a safety sign should also display the current sign.
4. Safety signs have a part number in the lower righthand corner. Use this part number when ordering replacement parts.
5. Safety signs are available from your authorized Distributor or Dealer Parts Department or the factory.

www.tmgindustrial.com 6 / 22 TOLL FREE: 1-877-761-2819
Preparation
1. Never use the machine until you have read and completely understand this manual, the skid steer tractor Operator's
Manual and each of the Safety Messages found on the safety signs on the skid steer tractor and machine.
2. Personal protection equipment including hard hat, safety glasses, safety shoes, and gloves are recommended during
assembly, installation, operation, adjustment, maintaining, repairing, removal, cleaning, or moving the unit. Do not allow
long hair, loose fitting clothing or jewelry to be around equipment.
3. PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS!
Power equipment with or without equipment attached can often be noisy enough to cause permanent, partial hearing loss. We
recommend that you wear hearing protection on a full-time basis if the noise in the Operator's position exceeds 80db. Noise
over 85db on a long-term basis can cause severe hearing loss. Noise over 90db adjacent to the Operator over a long-term basis
may cause permanent, total hearing loss. NOTE: Hearing loss from loud noise (from tractors, chain saws, radios, and other
such sources close to the ear) is cumulative over a lifetime without hope of natural recovery.
4. Clear working area of stones, branches or hidden obstacles that might be hooked or snagged, causing injury or damage.
5. Use only in daylight or good artificial light.
6. Be sure machine is properly mounted, adjusted and in good operating condition.
7. Ensure that all safety shielding, and safety signs are properly installed and in good condition.
Maintenance Safety
1. Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.
2. Follow good shop practices.
a) Keep service area clean and dry.
b) Be sure electrical outlets and tools are properly grounded.
c) Use adequate light for the job at hand.
3. Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed building. The exhaust
fumes may cause asphyxiation.
4. Before working on this machine, shut off the engine, set the brake, and turn fuel valve off.
5. Never work under equipment unless itis blocked securely.
6. Always use personal protection devices such as eye, hand and hearing protectors, when performing any
service or maintenance work. Use heavy or leather gloves when handling blades.
7. Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must
be used to restore your equipment to original specifications. The manufacturer will not be responsible for injuries or
damages caused by use of unapproved parts and/or accessories.

www.tmgindustrial.com 7 / 22 TOLL FREE: 1-877-761-2819
8. A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this equipment.
9. Periodically tighten all bolts, nuts and screws and check that all electrical and fuel connections are properly secured to
ensure unit is in a safe condition.
10. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing
unit in service.
Hydraulic Safety
1. Make sure that all the components in the hydraulic system are kept in good condition and are clean.
2. Before applying pressure to the system, make sure all components are tight, and that lines, hoses and couplings are not
damaged.
3. Do not attempt any makeshift repairs to the hydraulic lines, fittings, or hoses by using tapes, clamps or cements. The
hydraulic system operates under extremely high pressure. Such repairs will fail suddenly and create a hazardous and
unsafe condition.
4. Wear proper hand and eye protection when searching for a high-pressure hydraulic leak. Use a piece of wood or cardboard
as a backstop instead of hands to isolate and identify a leak.
5. If injured by a concentrated high-pressure stream of hydraulic fluid, seek medical attention immediately. Serious infection
or toxic reaction can develop from hydraulic fluid piercing the skin surface.
6. Relieve pressure on hydraulic system before maintaining or working on system.
Transport Safety
1. Comply with state and local laws governing safety and transporting of machinery on public roads.
2. Check that all the lights, reflectors and other lighting requirements are installed and in good working condition.
3. Do not exceed a safe travel speed. Slow down for rough terrain and cornering.
4. Do not drink and drive.
5. Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, intersections,
etc. Watch for traffic when operating near or crossing roadways.

www.tmgindustrial.com 8 / 22 TOLL FREE: 1-877-761-2819
To the New Operator or Owner
Follow all safety instructions exactly. Safety is everyone's business. By following recommended procedures, a safe working
environment is provided for the operator, bystanders, and the area around the worksite. Untrained operators are not qualified to
operate the machine.
Many features incorporated into this machine are the result of suggestions made by customers like you. Read this manual
carefully to learn how to use the chipper safely and how to set it to provide maximum field efficiency. By following the using
instructions in conjunction with a good maintenance program, your Skid Steer Wood Chipper will provide many years of trouble-
free service.
OPERATION
Machine Components
The TMG Skid Steer Mounted Wood Chipper is a rotor with blades for chipping wood. A hinged feed hopper moves the wood
material into the rotor. Each rotor is designed with 4 blades and a twig-breaker to generate the small pieces of wood. A
stationary knife at the rear of the rotor housing is placed by the moving knives to shear, chip or chop the material.
The skid steer tractor provides rotational power through its hydraulic system into the hydraulic motor on the rotor shaft. This
drive system is contained in the front frame.

www.tmgindustrial.com 9 / 22 TOLL FREE: 1-877-761-2819
Machine Break-In
Although there are no operational restrictions on the Wood Chipper when used for the first time, it is recommended that the
following mechanical items be checked:
After operating for 1 hour:
1. Torque all fasteners and hardware.
2. Check condition of rotor bearings.
3. Check the condition and clearance of the twig-breaker, rotor and stationary blades. Adjust or replace as required.
4. Check for entangled material. Remove all entangled material before resuming work.
5. Lubricate all grease fittings.
After operating for 10 hours:
1. Repeat steps 1 through 5 listed above. (After operating for 1 hour)
2. Go to the normal servicing and maintenance schedule as defined in the Maintenance Section.
Pre-Operation Checklist
Efficient and safe operation of the TMG Skid Steer Mounted Wood Chipper requires that each operator reads and understands
the using procedures and all related safety precautions outlined in this section. A pre-operation checklist is provided for the
operator. It is important for both the personal safety and maintaining good mechanical condition that this checklist is followed.
Before operating the Wood Chipper and each time thereafter, the following areas should be checked off:
1. Lubricate the machine per the schedule outline in the Maintenance Section.
2. Check the rotor, blades, and twig-breaker. Remove any twine, wire or other material that has become entangled.
3. Check the condition and clearance of the twig- breaker, rotor, and stationary blades. Adjust or replace as required.
4. Check that all bearings turn freely. Replace any that are rough or seized.
5. Make sure that all guards and shields are in place, secured and functioning as designed.
6. Check the condition of the curtain in the feed hopper. It must be in good condition to prevent chips from flying out.

www.tmgindustrial.com 10 / 22 TOLL FREE: 1-877-761-2819
Machine Set-Up
Follow this procedure to prepare and setup the machine at the work site:
1. Use the skid steer to position the Wood Chipper at the work site.
IMPORTANT
Position the machine so the prevailing wind/breeze blows the exhaust
gases/fumes away from the operator's station.
2. Lower the feed hopper down into its working configuration:
a. remove the nuts on the hopper anchor bolts,
b. unpin and the feeder hopper latch
c. carefully lower the hopper and secure it with the with the nuts on the anchor bolts.
d. Secure the feed hopper latch to the discharge chute with the latch pin
Hydraulic Connections & Mounting
The machine is shipped from the factory in a basic, universal configuration that allows it to be mounted to any model skid
steer. However, the skid steer must be equipped with a remote hydraulic outlet on the front of the cab frame.
The wood chipper should always be located on a level, dry area that is free of debris and other foreign objects. When attaching
the wood chipper to a skid steer, follow this procedure:
1. Make sure that all bystanders, especially small children are clear of the work area.

www.tmgindustrial.com 11 / 22 TOLL FREE: 1-877-761-2819
2. Make sure there is enough room and clearance to safely drive up to the wood chipper.
3. Drive up to the wood chipper while aligning the mounting components, and hook up into the mount.
4. Secure the mounting:
a. Drive into the mounting frame.
b. Seat the top of the face plate into the frame of the wood chipper.
c. Raise the loader and tilt the face plate until it is fully mated.
5. Engage the lock pins to secure the wood chipper to the loader.
6. Connect the hydraulics:
a. Use a clean rag or paper towel to clean the dirt from the couplers
on the hose ends of the skid steer.
b. Connect the hoses to the skid steer couplers. Be sure the
couplers are securely seated.
c. Route and secure the hoses along the frame with clips, tape or
plastic ties to prevent binding and pinching. Be sure to provide
slack for tilting.

www.tmgindustrial.com 12 / 22 TOLL FREE: 1-877-761-2819
7. Raise the wood chipper.
8. Check that all hydraulic connections and locks are secure before beginning work.
Reverse the above procedure when unhooking.
Place planks or boards under the frame for extra support if required.
Chipping Operation
The Wood Chipper is a strong, rugged machine that is built to a
straightforward design which provides consistent chipping of logs up to 6"
(152mm)
Always wear personal protective equipment (PPE) whenever operating the
machine. This includes but is not limited to protective shoes with slip
resistant soles, protective goggles or face shield, heavy gloves, hearing protection and protective clothing.
Do not place metal, bottles, cans, rocks, glass or other solid material into the wood chipper. If something like this gets into the
machine, stop the machine immediately for a detailed inspection. Stop engine, remove ignition key and place in your pocket
and wait for all moving parts to stop before inspecting or unplugging. Inspect machine for damaged or loosened parts before
resuming work.
Caution and care should be exercised when feeding material into the feeder. Do not reach into the
hopper past the curtain barrier.
a. Before beginning to feed the rotor is up to speed.
b. Slowly slide the wooden material into the feed hopper and move it into the rotor.
c. Do not force the material into the rotor, as the material engages the rotor, the rotor will draw the
material in. Use continuous lite pressure to guide in the material.
d. Be aware of how much material you feed in, slow down or stop if the rotor begins to slow down.
e. Do not reach into the feed hopper further than the curtain to be sure not to contact the blades on the rotor.

www.tmgindustrial.com 13 / 22 TOLL FREE: 1-877-761-2819
f. Use a stick or branch to push any piece of material into the rotor that does not move on its own. If the jam persists then
stop the engine and wait for the rotor to stop and then clear the jam. Do not take a chance with getting your hand caught
in the rotor.
g. Ensure your wood chip pile is contained and doesn't affect the immediate work area.
Unplugging
Although the machine is designed to handle a wide variety of material without any problem, occasionally it plugs. When the
machine plugs, follow this procedure to unplug:
a. Clear the area of bystanders, especially small children.
b. Turn off the hydraulics, stop the engine, remove the ignition key and place it in your pocket and wait for all moving parts
to stop before unplugging.
c. Pull the material out of the feed hopper. Be sure all the material is out, and nothing is jammed or wedged between the
input opening and the rotor.
d. Pull the material out of the discharge hood. Use a stick to poke loose any material jammed into the discharge hood. Do
not allow anything to remain in this area.
e. Check that everyone is clear of machine before restarting engine.
f. Start the engine turn on the hydraulics, and resume working.
Severe Plug
a. Clear the area of bystanders, especially small children.
b. Turn off the hydraulics, stop the engine, remove the ignition key and place it in your pocket or remove spark plug wire, and
wait for all moving parts to stop before unplugging.
c. Loosen the feed hopper anchor nuts and raise the feed hopper.
d. Remove jammed material from inside the rotor compartment.
e. Clean out the discharge area/rotor.
f. Open the upper rotary housing and clean out the housing.
g. Be sure to turn the rotor by hand to be sure there is nothing jammed between the rotor and stationary blades.
h. Close, install and fold down all components opened to unplug. Tighten fasteners to their specified torque.
i. Check that everyone is clear of machine before restarting engine.
j. Start the engine turn on the hydraulics and resume working.

www.tmgindustrial.com 14 / 22 TOLL FREE: 1-877-761-2819
MAINTENANCE
By following a careful service and maintenance program for your machine, you will enjoy many years of trouble-free operation.
Blade and Breaker Maintenance
The rotor and ledger blades need to be sharp for the Chipper to perform as expected. Periodic inspection is recommended.
Keep the blades sharp to reduce the amount of power required during operation. Watch the sharpness of the blades when
processing material with a lot of sand, soil or dirt mixed with it. Reverse or sharpen the blades if the cutting edge becomes dull.
Twig breaker should be inspected for gouges or bent.
Rotor Blades Maintenance
The rotor is equipped with 4 blades spaced evenly to keep the rotor in balance. If one needs to be changed, the one opposite
should also be changed.
It is recommended that the rotor blades be removed from the rotor when sharpening. Always sharpen the blades at a 45° angle
to provide the best cutting effect as it meets the stationary blade. Be sure to tighten the blade mounting bolts to their specified
torque when reinstalling the blades to the rotor.
1. Turn off the hydraulics, stop the engine, remove the
ignition key, and place it in your pocket and wait for
all moving parts to stop.
2. Remove the bolt that secures the upper rotor
housing, and carefully open the rotor housing.
3. Manually rotate chipper rotor plate so that the blade
is fully exposed
4. Remove the bolts that hold the rotor blade to the
rotor, remove the blade.
5. Rotate the blade and reinstall or replace with new or
resharpened blade.
6. Ensure the blade is properly oriented, with the
leading edge out. The blade is designed to fit into
the rotor one way only. See diagram for proper
installation.
7. Tighten down bolts as specified in the torque chart.
8. Repeat steps for remaining blades.

www.tmgindustrial.com 15 / 22 TOLL FREE: 1-877-761-2819
Ledger Blades Maintenance
The TMG-WC62S is equipped with a ledger (stationary) blade that acts as a shear for the moving rotor blades. The ledger blade
is designed with 4 usable corners. When the corner facing the rotor blade rounds over, remove the blade and reinstall with a
different corner facing the rotor blade. It is recommended that the clearance between the rotor and stationary blades be set and
maintained at 1/32 to 1/16 " (.76 - 1.52 mm) to obtain the best performance.
1. Turn off the hydraulics, stop the engine, remove the ignition key and place it in your pocket and wait for all moving parts
to stop.
2. Remove the 2 bolts that hold the ledger blade to the
ledger mount, remove the blade.
3. Rotate the blade and replace or replace with new or re-
sharpened blade.
4. Hand tighten the bolts and set the clearance between the
ledger and rotor blades at 1/32 - 1/16" .
5. Tighten down bolts as specified in the torque chart
Hydraulic System
WARNING!
A small stream of oil from a pinhole leak could penetrate your skin if contacted. To avoid an accident that could result in Death
or Serious Injury, never use your hand or other body parts in an attempt to locate a hydraulic leak.
NOTICE!
Always release the hydraulic system pressure from the hydraulic circuits prior to removing the attachment or any hydraulic
system service work.
Bolt Torque
CHECKING BOLT TORQUE
The tables shown below give correct torque values for various bolts and cap screws. Tighten all bolts to the torques specified
in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with
the same strength bolt.
Torque figures indicated above are valid for non-greased or non-oiled threads and heads unless otherwise specified. Therefore,
do not grease or oil bolts or cap screws unless otherwise specified in this manual. When using locking elements, increase
torque values by 5%.
* Torque value for bolts and cap screws are identified by their head markings

www.tmgindustrial.com 16 / 22 TOLL FREE: 1-877-761-2819
SPECIFICATION
Specifications & Capacities
• Universal skid steer style hookup
• Chipping capacity: 6"
• Max hydraulic pressure: 3600 psi
• Hydraulic flow rate: 27-35GPM
• Speed rated: 470-635 RPM
• Rotor size: 30"
• Rotor weight: 190 lb
• Rotor knives: 4/reversible
• Discharge hood height: 82”
• Feeding housing opening: 6 1/2" x 10"
• Hopper opening: 25" x 25"

www.tmgindustrial.com 17 / 22 TOLL FREE: 1-877-761-2819
PARTS LIST
Wood Chipper Assembly

www.tmgindustrial.com 18 / 22 TOLL FREE: 1-877-761-2819
Part No.
Ref.
Part Description
QTY
1
GB/T6170
Nut M10
4
2
GB/T93
Spring Washer 10
4
3
GB/T96.1
WASHER 10
10
4
BX62R.7
Knife, Ledger
1
5
GB/T96.1
WASHER 12
3
6
BX62R.11
Ledger Knife bolt
2
7
GB/T5786
BoltM12x1.5x40
2
8
GB/T 93
Spring Washer 12
3
9
BX62HS.1
Housing, Bottom Rotor
1
10
GB/T 5783
Bolt M16×50
6
11
GB/T 889.1
Nut M16
6
12
BX62H.15
Skid steer mount plate
1
13
GB/T5783
BoltM12x35
7
14
BX62R.6
Twig Breaker
1
15
GB/T 97.1
WASHER 12
6
16
GB/T889.1
Nut M12
6
17
BX62HS.16
Cover
1
18
GB/T 97.1
WASHER 10
6
19
GB/T5786
BoltM12x1.5x30
1
20
GB/T 5783
BoltM10×25
6
21
BX62HS.12
Hydraulic components
1
22
BX42HS.10
Coupling XL6
1
23
GB/T 1096-1979
Flat key A10*45
1
24
GB/T5786
Bolt M14*1.5*40
8
25
GB/T 93
SPRING WASHER 14
8
26
GB/T 97.1
WASHER 14
8
27
GB／T7810
Bearing UCF210
2
28
BX62HS.3
Rotor Assembly
1
29
BX62R.13
Bearing cover
1
30
BX62S.2
Infeed Hopper Assembly
1
31
BX62R.5
Upper Weldment
1
32
GB/T 4329
Lick pin
1
33
BX62R.4
Discharge Chute Assembly
1
34
GB/T6177.1
Nut M10
2

www.tmgindustrial.com 19 / 22 TOLL FREE: 1-877-761-2819
Hydraulic components
Part No.
Ref.
Part Description
QTY
A1
BX42HS.12.2
Hydraulic hose 02: Length:2400mm
1
A2
GE22LREDOMD
END STRAIGHT JOINT G3/4"-M30*2
2
A3
GB/T 70.1
Bolt M10*60
4
A4
GB/T 93
Washer 10
4
A5
BX62HS.12.3A
valve block
1
A6
GE10LRMOED
END STRAIGHT JOINT G1/4"-M16*1.5
1
A7
BMTY-200-4-FD-D-M
Motor
1
A8
BX42HS.12.1
Hydraulic hose 01: Length:2400mm
2
A9
GE10LR3/8EDOMD
END STRAIGHT JOINT G3/8"-M16*1.5
1
A10
KIS-PT-G03SF
FLAT FACED COUPLERS G3/8 FEMALE
1
A11
KIS-PT-G04SP
FLAT FACED COUPLERS G1/2 MALE
1
A12
KIS-PT-G04SF
FLAT FACED COUPLERS G1/2 FEMALE
1
A13
GE22LR1/2EDOMD
END STRAIGHT JOINT G1/2"-M30*2
2
A14
GB/T 5783
Bolt M12*45
4
A15
GB/T 889.1
NUT M12
4
A

www.tmgindustrial.com 20 / 22 TOLL FREE: 1-877-761-2819
Rotor Assembly
Part No.
Ref.
Part Description
QTY
B1
BX62R.3.2
Knife, Rotor
4
B2
GB/T 97.1
WASHER 12
16
B3
GB/T 93
SPRING WASHER 12
16
B4
GB/T 5783
Bolt M10*20
16
B5
BX62R.3.1
Rotor Weldment
1
B