Tomar TRX-03 User manual

IS0614-00
3/15/2016
TOMAR OFF-ROAD, 2100 W OBISPO AVE, GILBERT, AZ 85233
800-338-2133 www. omaroff-road.com
Product Manual
TRX SERIES LIGHTS
TRX-03 TRX-06 TRX-10

IS0614-00
Page 2 of 5
Wiring
Power Wires
•Red o +Vdc
•Black o -Vdc
Wire Runs
The able below lis s he maximum recommended wire run for he power and ground cables in fee .
Par
Number Lamps WIRE GAUGE
18 16 14 12 10 8
TRX-03 1 89 142 225 361 575 914
TRX-06 1 51 81 129 206 328 522
TRX-10 2 25 40 64 103 164 261
Common Switch Wiring Configuration

IS0614-00
Page 3 of 5
Mounting
TRX ligh bars include L shape moun ing bracke s designed o secure he ligh bar o a fla surface. The
bracke will allow a 135° range of mo ion. For addi ional moun ing op ions visi www. omaroff-road.com.
1. A ach he moun ing foo o he ligh bar using he 1/4 -20 socke head screws and ¼” fla
washers included wi h he ligh bar, leaving he screws finger igh .
2. Place he ligh bar wi h a ached moun ing fee on a fla surface ha has sufficien s reng h
o suppor i s weigh . Using he holes in he moun ing bracke s as a empla e mark he
loca ion of he moun ing holes. The moun ing holes in he bracke are designed o free fi
¼ inch hardware. Recommended drill sizes for ¼” hardware are 17/64 ” for clearance holes
and 13/64 for apped holes. No e: he hole pa ern on he foo is on 2” cen ers. For he hole
spacing be ween he moun ing fee refer o he Dimensions sec ion below.
3. Once he ligh bar is secured o he moun ing surface, adjus he ligh bar o he desired
angle and igh en he ¼- 20 socke head screws o approx. 36 in/lb.

IS0614-00
Page 4 of 5
Dimensions
Nominal
Length
Lamps
Dim "A"
Dim "B"
Dim "C"
Dim "D"
Dim "E"
Dim "F"
3
1
3.41
4.66
5.66
3.00
4.25
3.82
6
1
5.68
6.93
7.93
3.00
4.25
3.82
10
2
10.23
11.48
12.48
3.00
4.25
3.82
Moun ing Hole Spacing
Ou side Dimensions

IS0614-00
Page 5 of 5
Recommended Fuse/Breaker Sizing
Replacing a lamp module
All TRX lamp modules are in erchangeable and can be used in any posi ion on he ligh bar. This offers he
flexibili y o configure a ligh bar for any mission wi h perfec balance of flood, spo or dual color amber
whi e modules.
Wi h his modular design he replacemen of a TRX Lamp couldn’ be easier. Each module is herme ically
sealed so replacemen will no compromise he wa er igh in egri y of he ligh bar or void he warran y.
To replace a lamp module simply remove he wo lamp clips using a 9/64” hex ool. Unplug he lamp from
he wa erproof connec or, plug he new lamp in and rea ach he lamp clips.
Maintenance
The bes cleaning me hod is o gen ly wash he ligh bar wi h a solu ion of mild soap and lukewarm wa er,
using a sof clo h or sponge o loosen any dir or grime. Thoroughly rinse wi h clean wa er o remove any
cleaner residue and dry he surface wi h a sof clo h o preven wa er spo ing.
If using a high-pressure wa er cleaner and/or a s eam cleaner he pressure should no exceed 1,450psi.
The use of addi ives o he wa er and/or s eam should also be avoided.
Important Considerations for Le an lenses:
• Never use abrasive or highly alkaline cleaners.
• Never use aroma ic or halogena ed solven s like oluene, benzene, gasoline, ace one or carbon
e rachloride.
• Con ac wi h harsh solven s such as me hyl e hyl ke one (MEK) or hydrochloric acid can resul in
surface degrada ion and possible crazing.
• Never scrub lenses wi h brushes, s eel wool or o her abrasive ma erials.
Par Number Lamps
Amp draw
@13.8Vdc
Fuse/Breaker Size
(A)
TRX
-
03
1
1.3
3
TRX
-
06
1
2.1
5
TRX
-
10
2
4.2
10