Robert Juliat daus 861 User manual

EN
DALIS - 861
Firmware V1.XX – 27/03/17
DN41108100
Robert Juliat S.A.S. 32, rue de Beaumont, F60530 Fresnoy-en-Thelle - phone : [phone] - fax : [phone] - [email protected]
Dalis - 861
Asymmetric washlight
8 colour LED 150W Asymmetric washlight
For more information,
Please download the full manual online
http://www.robertjuliat.com/ambiance_lighting/dalis861.html
Package contents:
1x Dalis 861
1x Neutrik PowerCon© True1 connector
(ref. NAC3FX-W)
Quick start guide

EN
EN -1-
1 User’s instructions
GENERAL INSTRUCTIONS
1. Not for residential use.
2. These fixtures must only be serviced by a
qualified technician.
3. In addition to the instructions indicated on this page,
relevant health and safety requirements of the
appropriate EU Directives must be adhered to at all
times.
4. This fixture is in compliance with section 17 - Lighting
appliance for theatre stages, television, cinema and
photograph studios. Standards NF EN 60598-1 and
NF EN 60598-2-17.
5. This fixture is rated as IP20, and is for indoor use
only.
FIXTURE
6. Ensure fixture is correctly mounted on an appropriate
support.
7. Protection screens must be replaced in the event of
any damage, such as cracks or deep scratches, since
these might reduce performance.
8. When hung or flown the fixture must be secured by
an additional hanging accessory (such as a safety
cable or bond) of suitable length.
9. Safety bonds or cables must be securely attached to
the fixture and be as short as possible, or rolled up as
necessary, to minimise travel distance should the
fixture be dislodged.
10. WARNING: LED source become hot during use.
Allow fixture to cool before servicing.
11. Do not tamper with design of fixture nor any of its
safety features.
12. Tighten electrical mains cable connections regularly
and replace with one of identical specification if
damaged.
13. Use only with correct power supply.
14. Do not orientate the fixture towards a source of light
(sun, fixture), in particular for LED versions.
VENTILATION
15. Keep well away from flammable material.
16. Not for outdoor use. Do not cover. Do not permit
fixture to get wet.
17. To avoid overheating, do not obstruct air vents.
PLEASE NOTE
These products have been built to conform to European
standards relating to professional lighting equipment. Any
modification made to our products will void the
manufacturers' warranty.
2 Installation

EN
EN -2-
3 Electrical / Data connection
1
Power
input:
• Connector: Neutrik powerCON TRUE1
• Voltage: 90 à 264V 50/60Hz
• Power consumption: 140W max.
2
Power
output:
• Connector: Neutrik powerCON TRUE1
• Daisy chain:
§ 230V: 20 units max
§ 120V: 10 units max
§ 100V: 8 units max
3
Data In:
• Connector: XLR 5-pin
• Protocol: USITT DMX 512-A / RDM
4
Data Out:
• Connector: XLR 5-pin
• Protocol: USITT DMX 512-A / RDM
5
Ethernet:
• Connector: RJ45
• Protocol: Art-Net / sACN + software
update
4 DMX control
DMX address and control mode selection:
Data Mode
DMX
DMX Address
Start addresss : XXX
Mode X : XXXXXXX
Main screen
Personality

EN
EN -3-
5 DMX chart
DMX$
address$
Mode$1:$
FullMode16b$
Mode$2:$
FullMode16b$
Mode$3:$
Presetmode16b$
Mode$4$
Presetmode8b$
1$
Dimmer&
Dimmer&
Dimmer&
Dimmer&
2$
Dimmer&fine&
Red&
Dimmer&fine&
Colour&presets&
3$
Red&
Green&
Colour&presets&
CCT&
4$
Red&fine&
Blue&
CCT&
Strobe&duration&
5$
Green&
Royal&blue&
Strobe&duration&
Strobe&speed&
6$
Green&fine&
Cyan&
Strobe&speed&
Response&time&
7$
Blue&
Amber&
Response&time&
Control&mode&
8$
Blue&fine&
Cool&white&
Control&mode&
&
9$
Royal&blue&
Warm&white&&
&
10$
Royal&blue&fine&
Strobe&duration&
&
11$
Cyan&
Strobe&speed&
&
12$
Cyan&fine&
Response&time&
&
13$
Amber&
Control&mode&
&
14$
Amber&fine&
&
15$
Cool&white&
&
16$
Cool&white&fine&
&
17$
Warm&white&&
&
18$
Warm&white&fine&
&
19$
Strobe&duration&
&
20$
Strobe&speed&
&
21$
Response&time&
&
22$
Control&mode&
&