Event Lighting PAR12x8A User manual

PRO PAR
Model No. PARRGBW12x8, PAR12x8A
PARRGBW5x8, PAR5x8A
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
Ver 2.3

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
Product Installation
Diagrams
Control Board Operation
DMX chart
Technical specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this number.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au
3
Lux Chart
PARRGBW5X8 PAR5X8A
PARRGBW12X8 PAR12X8A

www.event-lighting.com.au
4
Dimensions
PAR5
PAR12

www.event-lighting.com.au
5
CONTROL BOARD OPERATION
Display Options / Values Function
DMX Add <001> - <512> Set DMX address
DMX Cha <02> <03> <04> <06> <10> Select DMX channel mode
Dimmer <01> <02> <03> <04> <05> Select dimmer curve
Sound <Sen000> - <Sen100> Select sound active mode and the sensitivity level from
<Sen000> - <Sen100>
StaticC RGBW Models: R, G, B, W, GB, RB,
RG, RGB, RW, GW, BW, RGW,
RBW, GBW, RGBW
RGBA Models: R, G, B, A, GB, RB,
RG, RGB, RA, GA, BA, RGA, RBA,
GBA, RGBA
Select static colour
ManualC R<000> - <255>
G<000> - <255>
B<000> - <255>
W/A<000> - <255>
S<000> - S<100>
Set intensity of each colour separately for color mixing
and strobe rate
Auto Pr <Pr01> - <Pr07>
<Sp000> - <Sp100>
<Dim000> - <Dim255>
Select built-in automatic programs, auto run speed and
dimmer level
Mas/Sla <M> <S> Select Master/Slave modes
Reset <N> <Y> Recover manufactory default
DMX Address
After select the "DMX Add" and press “Enter”, use “Up” and “Down” button to select the desired DMX address, press
“Enter" to save new setting
DMX Mode
After select the "DMX Cha" and press “Enter”, use “Up” and “Down” button to select the desired DMX mode, press
“Enter" to save new setting
Dimmer Curve
After select the "Dimmer" and press “Enter”, use “Up” and “Down” button to select the desired dimmer curves
Sound Active Mode
Entered “sound” mode, use “Up” and “Down” button to select the sensitivity Sen000-Sen100, press “Enter” to save new
setting
Static Colour Mode
Entered "Static C" mode, you can select the desired solid color via the “UP” or “DOWN” buttons, press “Enter" to save
new setting

www.event-lighting.com.au
6
8W RGBW LED 8W RGBA LED
Value: Function: Value: Function:
R Red R Red
G Green G Green
B Blue B Blue
W White A Amber
GB Green + Blue GB Green + Blue
RB Red + Blue RB Red + Blue
RG Red + Green RG Red + Green
RGB Red + Green + Blue RGB Red + Green + Blue
RW Red + White RA Red + Amber
GW Green + White GA Green + Amber
BW Blue + White BA Blue + Amber
RGW Red + Green + White RGA Red + Green + Amber
RBW Red + Blue + White RBA Red + Blue + Amber
GBW Green + Blue + White GBA Green + Blue + Amber
RGBW Red + Green + Blue + White RGBA Red + Green + Blue + Amber
Manual Color Mode
Entered "Manual C" mode, use “Up” and “Down” button to select the each colour (RGBW or RGBA) intensity from 000
to 255, select strobe (S) speed from S000 to S100. (S000 is strobe off). Press “Enter" to save new setting.
Auto Run Mode
Function
Pr 01 RGBW Model : R G B W colour switching
RGBA Model : R G B A colour switching
Pr 02 15 colour switching
Pr 03 RGBW Model : R G B W colour fading
RGBA Model : R G B A colour fading
Pr 04 15 colour fading
Pr 05 Color Macros Fading
Pr 06 Sound active mode
Pr 07 Multi fixture chases
Set auto run Pr 01 - Pr 05
Entered "Auto Pro" mode, use “Up” and “Down” button to select the built-in programs. Press “Enter" and use “Up” and
“Down” button to select auto run speed from <Sp000> to <Sp100>. Press “Enter" and use “Up” and “Down” button to
select dimmer of “Auto Pro” from <dim000> – <dim255>. Press “Enter" to save new setting.
Set sound active mode Pr 06
Entered “Auto Pro” mode, use “Up” and “Down” button to select the built-in program “Pr 06”, press “Enter” and use “Up”
and “Down” button to select the sound sensitivity level from <Sen000> to <Sen100>, press “Enter" to save new setting.

www.event-lighting.com.au
7
Set multi fixture chases Pr 07
Before starting, go to each fixture and reset the menu to fixture defaults.
1. On the master unit, setup the DMX address to the total number of fixtures in the string. For example, you may
have a total of 20 par cans including the master, so the DMX address should be set to “20”.
2. On the master unit, go to master/slave menu setting and set the unit to master
3. On the master unit, set the unit to “Auto Mode” “Pr 07” which supports multi fixture chases.
4. On each slave unit, setup the DMX address to the fixture position in the string. For example, if this unit is the
2nd unit in the string including the master, then set the DMX address to 2. If this the last unit of 20, then the
DMX address should be set to 20. It is possible to double up fixture positions as well as fixture 1.
5. On each slave, go to the master/slave menu setting and set it to slave.
Master/Slave Operation
Set the master fixture to one of the stand-alone operating modes: automatic, sound, static color or manual color modes.
Set the slaves, entered "Mas/Sla" mode, set to “S”, press “Enter” to confirm.
DMX Chart
2 channels Mode
Channel Value Function
1 000-255 Warm white to cool white
2 000-255 dimmer 0% ~ 100%
3 channels Mode
Channel Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 channels Mode
Channel Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 RGBW Model : White: 0% ~ 100%
RGBA Model : Amber: 0% ~ 100%

www.event-lighting.com.au
8
6 channels Mode
Channel Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 RGBW Model : White: 0% ~ 100%
RGBA Model : Amber: 0% ~ 100%
5 000-255 Master Dimmer 0% ~ 100%
6
000-009 No function
010-019 Sound Active
020-255 Strobe : Slow ~ Fast (1~30Hz)
10 channels Mode
RGBW
Channel
Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 RGBW Model : White: 0% ~ 100%
RGBA Model : Amber: 0% ~ 100%
5 000-255 Master Dimmer 0% ~ 100% for CH1, 2, 3, 4 & 8
6 000-009 Strobe OFF
010-255 Strobe (slow-fast 1-30Hz)
7
000-019 No Function
020-039 RED 100% / GREEN 0% ~ 100% / BLUE 0%
040-059 RED 100% ~ 0% / GREEN 100% / BLUE 0%
060-079 RED 0% / GREEN 100% / BLUE 0% ~ 100%
080-099 RED 0% / GREEN 100% ~ 0% / BLUE 100%
100-119 RED 0% ~ 100% / GREEN 0% / BLUE 100%
120-139 RED 100% / GREEN 0% / BLUE 100% ~ 0%
140-159 RED 100% / GREEN 0% ~100% / BLUE 0% ~ 100%
160-179 RED 100%~ 0% / GREEN 100% ~ 0% / BLUE 100%
180-200
RGBW Model :
RED 100% / GREEN 100% / BLUE 100% /WHITE 100%
RGBA Model :
RED 100% / GREEN 100% / BLUE 100% /AMBER 100%
201-204 Color Temperature 1
Warm
Cool
205-209 Color Temperature 2
210-214 Color Temperature 3
215-219 Color Temperature 4
220-224 Color Temperature 5
225-229 Color Temperature 6
230-234 Color Temperature 7
235-239 Color Temperature 8

www.event-lighting.com.au
9
240-244 Color Temperature 9
245-249 Color Temperature 10
250-255 Color Temperature 11
8
000-009 No Function
010-049 RGBW Model : R G B W colour switching
RGBA Model : R G B A colour switching
050-090 15 colour switching
091-131 RGBW Model : R G B W colour fading
RGBA Model : R G B A colour fading
132-172 15 colour fading
173-213 Color Macros Fading
214-255 Sound active mode
9 000-255 Speed of auto programs (slow ~ fast) or sound sensitivity for CH8
10
000-009 Use dimmer curve from setting of control board
010-057 16 bits Linear dimmer 1
058-106 16 bits Non-linear dimmer 2
107-155 16 bits Non-linear dimmer 3
156-204 16 bits Non-linear dimmer 4
205-255 8 bits Linear dimmer 5
TECHNICAL SPECIFICATIONS
Model PARRGBW5X8 PAR5X8A PARRGBW12X8 PAR12X8A
Dimensions and Weight
Overall size LxWxH (mm) 207x227x120 263x293x98
Weight (kg) 1.9 3.2
Power
Power Supply 100~240V AC, 50/60 Hz
Power Consumption (w) 40 98
Power I/O IEC input connector IEC input/output connector
Fuse T 1 A, 250 V T 2 A, 250 V
LED 5pcs 8W RGBW 5pcs 8W RGBA 12pcs 8W RGBW 12pcs 8W RGBA
Operation Modes DMX, auto run, sound active, master/slave, manual colour control, static colour control
Beam Angle 22°/ optional 55°
Refresh Rate 2940Hz
DMX Channel mode 2, 3, 4, 6, 10
DMX Connectors 3-pin XLR / optional 5-pin XLR
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au