Toneczar Effects Echoczar User manual

IN
EFFECT
OUT
DIRECT
OUT
© 2008 Ed Rembold, Toneczar Effects
[email protected]
100%
wet
Feedback On
(red LED)
MIX 1DELAY 1REPEATS SAFETYDELAY 2
Delay 2
(yellow LED)
50/50 mix
100%
dry
18 VDC IN
IN
PHASE
OUT
DELAY 1/2 FEEDBACKON/BYPASS
min maxmin max
50/50 mix
100%
wet
100%
dry
MIX 2
100 ms 1 sec
Delay 1
(green LED)
ECHO
MODE
DELAY
VINT
MODE
MOD
NORM
FX OUT
MUTE
multi-head
reverb off s-back
echoczar
100 ms 1 sec
On/Bypass
(red LED)
delay 1
green channel
delay 2
yellow channel
echoczar
MIX 1 & MIX 2
individual Mix knobs allow each channel (Delay 1 and Delay 2)
to have a separate mix
for two amp (stereo) applications, the Mix knobs allow any
amount of delayed signal to be sent to the EFFECT amp
from 100% wet (delay only) to any mixture of delay and dry
DRY amp receives 100% dry signal from the Direct Out jack
EXPRESSION PEDAL INPUT
controls Delay 2 (yellow) delay time
ECHO/DELAY MODE (switch)
Echo Mode features repeats
which decay in a natural
manner, with soft feedback
Delay Mode features repeats
which can go on and on with
choppy feedback
EXPRESSION PEDAL INPUT
controls number of repeats for
both Delay 1 and Delay 2 or use
a channel insert cable to access
the delay path effects loop
SAFETY
active only in the Feedback Mode
wild feedback/self-oscillation at MIN
dampened feedback/self-oscillation at MAX
Delay 1 (Green) - use this channel for
your short delay setting.
Delay 2 (Yellow) - use this channel for
your long delay setting
switch between the two settings at any
time with the Delay 1/2 footswitch
add feedback/self-oscillation at any time
with the Feedback footswitch
if feedback runs away from you, turn
the Safety knob clockwise in small
increments until feedback is controlled
the same Safety setting will provide
a reasonably predictable feedback
response for both Delay 1 and Delay 2
may be used in an amp’s effects loop
Parallel loop - set Mix at 100% wet
Series loop - set Mix at 50/50
may be used either before or after
distortion but delay after distortion is
usually preferred
EFFECT OUT PHASE-SELECT (switch)
useful in correcting or creating a focused or
wide stereo image when using two amps or
when using both channels of a single amp like a
Fender Twin Reverb
CHANNEL INDICATOR LEDS
(GREEN or YELLOW)
ash to the exact delay time setting (tempo)
MULTI-HEAD MODE (center off switch)
add to either the Vintage or Modern Mode
Global - affects both Delay 1 and Delay 2
REVERB - sustains the repeat and adds reverb
S-BACK - adds slapback prior to main repeat
effect will vary with Delay Time settings
WARNING: will self-oscillate with Repeat
knob on MAX in either Multi-Head Mode
REPEATS
1 repeat at MIN
feedback/self-oscillation at MAX
EFFECT OUT MUTE/NORMAL (switch)
one amp: leave switch in the NORMAL position
two amps: when switched to NORMAL the
Direct Out and Effect Out jacks feature
hardwired, true-bypass switching
when switched to MUTE, the Direct Out
jack features hardwired, true-bypass
switching but the Effect Out jack will be
muted when footswitched to bypass
Actual Size:
4 ¼” deep
7 ½” wide
2 ¼” tall
analog stereo delay
VINTAGE/MODERN MODE (switch)
Vintage Mode - 100ms to
over 1 second, warm and thick
Modern Mode - 50ms to over 750ms,
brighter with more detail
instruction diagram

12
11
10
9
8
765
4
3
2
1
250ms
300ms
450ms
350ms
750ms
825ms
50ms
75ms
125ms
175ms
200ms
Modern Mode
o’clock positions
MIN. MAX.
12
11
10
9
8
765
4
3
2
1
325ms
400ms
625ms
475ms
1000ms
1100ms
100ms
125ms
175ms
225ms
275ms
Vintage Mode
o’clock positions
MIN. MAX.
Modern Mode Vintage Mode
© 2008 Ed Rembold, Toneczar Effects
[email protected]
echoczar
clock position to millisecond conversion chart
analog stereo delay